EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3KSM150PSTDR0 Whirlpool Mixer - Instructions

All Instructions for the 3KSM150PSTDR0
76 - 90 of 233

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
turn and quit
2 of 3 people found this instruction helpful.
  • GARY from BECKLEY, WV
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Disassembled gear housing and replaced worm gear/bracket assembly. The hardest part was cleaning and working around what looked like 2 pound of grease. I will contact you again if I need parts for anything. Thanks.
Was this helpful?
Thank you for voting!
Pinion gear failed, broken tooth mixer stalled and mixers wouldn't turn.
1 person found this instruction helpful.
  • Michael from Palos Park, IL
  • Easy
  • 30 - 60 mins
  • Screw drivers
Went to partselect, found model number, printed blow-up of mixer. Figured out disassenbly procedure. Drove out main pin removing mixer head from stand. Save pin. Drove out pin in mixer main shaft which allowed planetary head to be removed. Save pin.
Removed stainless steel bezel to expose screws for removal of bottom half of mixer body. Removed screws and carefully separated mixer halves using two screwdrivers as prybars. Care must be exercised to prevent chipping of paint on body.
Separated body. cleaned grease from gears to find actual problem. Removed broken geartooth and grease near broken part to make sure no small broken chips remained. Removed pinion shaft assembly, drove pin from gear releasing broken pinion/shaft. Save pin/
Cleaned grease from pinion shaft assembly using mineral spirits and a small brush to reveal how part could be disassembled. Ordered part immediately on-line. Part arrived 1 business day after it was ordered.
Reversed process for replacing pinion shaft. Applied fresh grease obtained from excess already in mixer, spun pinion shaft to make sure grease was properly distributed. Reinstalled pinion shaft assembly. CAREFULLY plugged in mixer and jogged motor to make sure all was free and that mixer worked. If you can repair this mixer, you should have enough sense to do this diagonistic. Keep fingers away from all moving parts, don't touch expposed electric wires. Plug in only after making sure switch is in off position. Jog using mixer switch. Make sure mechanism is free.
Complete re-assembly by following blow-up and reversing disassembly steps. It may be good to write down you disassemblly procedure if it is possible that you won't be reassembling within a day or two.
Was this helpful?
Thank you for voting!
The mixer broke the worm gear(the only plastic gear inside the mixer) and needed replaced.
1 person found this instruction helpful.
  • Dustin from JACKSONVILLE, NC
  • Easy
  • 15 - 30 mins
  • Screw drivers
I took apart the mixer housing and removed all the screws. The most difficult part was the two pins that needed to be removed with a metal punch. They were in fairly tight. The mixer came apart pretty easily and it was obvious which part needed to be replaced as it was broken and missing teeth. After replacing the gear and applying new gr ease for smooth operation, I simply put it back together and it has worked like new ever since.
Was this helpful?
Thank you for voting!
The original screw cap would not hold the mixer bowl in place anymore.
1 person found this instruction helpful.
  • Sylvia from HILTON, NY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
The new part was too large for the replacement job, but we used the self tapping screws that came with the mixer and screwed them in from the bottom to open the holes a little more since the original screws were to short to hold the new plate. Then we replaced the screws with longer screws and that seemed to do the trick!
Was this helpful?
Thank you for voting!
worm gear worn out
2 of 4 people found this instruction helpful.
  • michael from CISCO, GA
  • Very Easy
  • 15 - 30 mins
  • Screw drivers
I watched a short video on replacing the worm gear, although I did not know what the problem was until I watched the video. after the video ended I took the mixer apart and found the problem located a parts number an placed my order. got the part in one week put in the new part in about 20 minutes and it work like new. and the price was v ery reasonable
Was this helpful?
Thank you for voting!
Worn Worm gear. Mixer made a clunking noise and wouldn't turn.
1 person found this instruction helpful.
  • Deborah from HUNTINGTON, IN
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Followed your instructions from the internet and it was a simple fix. Mixer works great again. Thank You ..you made it easy!
Was this helpful?
Thank you for voting!
Stuck agitator shaft and dough hook
1 person found this instruction helpful.
  • Ana from PRT JEFFERSON, NY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
I had a sourdough batch get into the space where dough hook attaches and it got so stuck that nothing - not hot water baths, not pliers and screwdrivers got the dough hook released. I had to open up the mixer following partselect you tube instructions and replacing the parts. What was confusing to me at first is that my 45 year old mixer had an extra screw on top of the shaft that no longer is there for newer models. It took me longer than I am willing to admit to figure that the extra screw is not the result of me skimming the instructions - the original shaft and dough hook went to a friend who broke it attempting to disengage the two parts (the dough turned out to be a very strong form of glue!). The piece is working like new. I preferred the agitator shaft with a spring to hold the end piece tighter, but the new set up without a spring works just fine.
Was this helpful?
Thank you for voting!
Damaged gears in both machines. Been setting around for a few years broken. Gears broke way too soon.
1 person found this instruction helpful.
  • Ethan from MEADVILLE, PA
  • Very Easy
  • 15 - 30 mins
  • Screw drivers
Simply removed damaged gears. Very simple to do. Ordered gears. Replaced gears. Both working well ( so far. ) Machines are easy to dismantle. Just be sure to put the screws back in the holes you took them out of when dismantling...no lost screws. On the smaller model, took pictures of the wire positions to be sure they were replace d in the proper order. Larger model had no wires to remove.
Was this helpful?
Thank you for voting!
Splash from K45 KitchenAid Mixer Bowl
1 person found this instruction helpful.
  • Mark from LEXINGTON, SC
  • Very Easy
  • Less than 15 mins
The shield works sufficiently. Note that the shield is not a continuous circle as shown in the picture. This actually can be an asset because it can be installed or disassembled without stopping the mixer of having to lift the head while running.
Was this helpful?
Thank you for voting!
old stand mixer mixing bowl base will not firmly hold newer mixing bowls
1 person found this instruction helpful.
  • Susan from BATTLE GROUND, WA
  • Easy
  • 30 - 60 mins
  • Screw drivers
With a screw driver remove the screws holding the old base in place. With a flat head screw driver carefully pry and remove old mixer base. With 600 grit sandpaper clean and make smooth any burrs or rough spots in the mixer base recessed area. You can use some light grease and coat the outer edges of new mixer base and place in the now c leaned mixer base recessed area. The new base maybe a tight fit and not be fully seated in the recess. If a tight fit, place the piece of 2x4 piece of wood over the new part that is in the recess and carefully tap the base home using the sledge hammer. Check to see, if the base is fully seated. If not fully seated, tap again When fully seated replace the screws. You may have to adjust the height of the stand mixer head with mixer paddle attached for proper clearance between bowl and paddle. See your mixer manual for adjustment procedure
Was this helpful?
Thank you for voting!
Mixing bowl was no longer locking in place
1 person found this instruction helpful.
  • Amelia from AURORA, CO
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Unscrewed the existing screw cap, put the new one in place, replaced the screws. So easy!
Was this helpful?
Thank you for voting!
Hard to knock out pins, and connecting the top to the bottom after repair
1 person found this instruction helpful.
  • Sheldon from RICHMOND, TX
  • Easy
  • 30 - 60 mins
  • Socket set, Wrench (Adjustable)
watched how to repair
Was this helpful?
Thank you for voting!
Attachment hub stopped spinning
1 person found this instruction helpful.
  • Sarah from GRAPEVINE, TX
  • Easy
  • 30 - 60 mins
  • Screw drivers
Used youtube movies to disassemble the mixer and found that the gear was stripped. I kept the screws in labeled ziploc baggies so I wouldn't forget which screws went where. Once the part arrived, it was very simple to replace the gear. I regreased the mixer and then reassembled. The trickiest part was how greasy everything was! It was also hard to get the pin through the beater hub - I found a video that suggested using a very slim screwdriver to thread the hole before inserting the pin. This was the most involved part replacement I've done on my own, and it was very satisfying to get my mixer back in working order!
Was this helpful?
Thank you for voting!
Teeth on the gear were worn off.
1 person found this instruction helpful.
  • Curt from SHELBY, MI
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Took each area apart. Replaced the gear and reassembled it.
Was this helpful?
Thank you for voting!
Worm gear was worn out .
1 person found this instruction helpful.
  • Peter from SALADO, TX
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers, Wrench (Adjustable)
I watched the university of YouTube videos, and followed their instructions.
Was this helpful?
Thank you for voting!
All Instructions for the 3KSM150PSTDR0
76 - 90 of 233