EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3976 - Instructions

All Instructions for the 3976
121 - 135 of 489

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Refrigerator would not cool, freezer side froze up.
1 person found this instruction helpful.
  • Robert from Dublin, TX
  • Easy
  • 30 - 60 mins
  • Screw drivers
First I removed the two screws that hold the element in place. I then tried to pull the element out but the wires were hung behind the coils. My sholders are too wide to get into the freezer in order to use two hands to pull the connector apart and I could not seprate the connector with one hand. My skinny wife came to the rescue. She cli mbed right in and took the connector apart and plugged in the new one (and she is a blond too). I put it all back together in reverse of taking it apart. Being able to use only one hand was the my challenge, but the job was easy.
Was this helpful?
Thank you for voting!
water leaking from under dishwasher
1 person found this instruction helpful.
  • Edward from E LONGMEADOW, MA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Socket set, Wrench (Adjustable)
Water was leaking from under the GE dishwasher, but once we pulled it out, had apparently been going on for a little while. Turning the water off to the dishwasher made it stop, so it was happening even when the unit was not running, potentially indicating somewhere early in the path of the water to and into the machine.

Indeed , inspecting the water inlet vale showed a slow leak. Getting the replacement part was fine, and it fit the electrical, water inlet (existing 90-degree water inlet elbow), and water outlet connections just fine - but the original machine screws that held on the original water inlet valve did not work. It took a little research to figure out the new type of screw required, which was apparently a 10/16 Type AB, which seemed to be a less common type of sheet metal screw (with a point), as opposed to the original flat-ended machine screws. So, after ordering those separately (which were a bit expensive), it went together fine.

A note on the water inlet valve part just indicating the the threading on those parts has changed over time, so potentially ordering the screws to attach it might be worthwhile, would be good information to add about the water inlet valve.
Was this helpful?
Thank you for voting!
The door closing cam had broken up.
1 person found this instruction helpful.
  • J Barry from Sparta, NJ
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Socket set
The old cam had broken and was on the floor. I ordered one new cam. I should have been told to order at least two, I did not know they worked in pairs. So I had to re-order, I ordersed four, I was able to see that the other (freezer door has cracked cams) door will soon need replacement of the cams. I had trouble installing the new pa rt because the rivit also needed to ba replaced. I did a "Rube Goldgerg" to get the new part to sit properly. I drilled the hole open a little and forced the part into place. All is well. Thank you very much!
Was this helpful?
Thank you for voting!
Fridge door stopped closing.
1 person found this instruction helpful.
  • Peter from Woodland Hills, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set, Wrench (Adjustable)
The plastic door closing cams had broken after 17 years of use. It was tricky figuring out how the new cams fit as the old ones had disintegrated. Also you need 2 cams - not one. I first ordered only one. A detailed parts diagram would have helped. First unscrew the top door mount cover and then the top door mount. The fridge door t hen lifts up and off the lower door mount. Next is the hardest part - drilling off the old pop rivet which held the lower cam. The lower door mount had to be removed to get at the underneath of the pop rivet, and a bench vise was handy to hold it as I drilled off the old rivet. Then you need small stainless steel nut and bolt and split washer or lock nut to replace the rivet. Next unscrew the old upper cam from the underneath of the fridge door and replace. The large hole in the cam goes through the door hinge pins. The two plastic cams should interlock in a way that makes the door swing close. Anyway, now the door works fine.
Was this helpful?
Thank you for voting!
door didn't close on its own..
1 person found this instruction helpful.
  • George from Hawthorne, NY
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Wrench set
Removed door off hinge , remove bottom hinge, drill out rivet, lift off old cam & replace with new cam ,add new 1/4' BOLT(NOT SUPPLIED) to location where rivet was, reinstall bottom hinge & door ,check alignment, works perfect.

Thanks
Was this helpful?
Thank you for voting!
door would not close by itself - broke cam riser
1 person found this instruction helpful.
  • Mike from Alpharetta, GA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Wrench (Adjustable)
My right door (food door on side-by-side) stopped closing - I found pieces of the plastic washer (cam riser) on the floor. After reading the stories on the web I decided to order the new part - and YES there are many universal parts that work for Kenmore/GE. The part comes with two parts (hinge and cam riser) - you should install both to insure a good fit. I took 3 blocks of wood and a shim and supported the bottom center of the door, unscrewed the hinge off and dropped it out (3 minutes). The "only" tough part was unscrewing the cam riser from the bottom of the door - it required a very small socket and you will only have about 6-8 inches of work space. Be sure you have a socket that fits before you take the hinge off. The entire repair took less than 30 minutes and contrary to some of the posts, you DO NOT need to take the door off. Good as new again!
Was this helpful?
Thank you for voting!
Door no longer closed on it's own and would not stay closed all the time
1 person found this instruction helpful.
  • Dale from Hot Springs, AR
  • Easy
  • 15 - 30 mins
  • Nutdriver
First a big thank you to PartSelect.com. I read the stories posted by others before ordering the parts and found out that I probably needed 2 of these cams. So I followed the advice of others and ordered 2 cams. I'm really glad I did because once I got the door off I discovered both were broken up real bad. Maybe you guys should think abo ut offering them as a set?
Anyway the repair was fairly easy, except for the bottom cam which was revited to the bottom bracket. Again, thanks to the other stories about repairs with this part I was already expecting this. So the repair went like this. I removed the door by unscrewing the hinge on top(1 screw and 2 bolts). Took the door off and laid it on its side. Removed the bottom bracket( 2 bolts). Used a drill to drill out the rivit. Used a spare screw/nut that I had in a tool box to fasten the cam to the bracket. Put it all back together and I was done. The biggest challenge was figuring our if I needed 2 cams,so with the advice of others on your site, my repair was a snap.
Was this helpful?
Thank you for voting!
Bottom cam at bottom of door broken.
1 person found this instruction helpful.
  • Wayne from Concord, NC
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Read the how to's AFTER ordering the part. 2 things....1) I wish I had read the comments first and 2) it was much easier than the comments led me to believe.

Had I read the comments first, I would have known to order BOTH the upper and lower cam....though there not a problem with the operation of the door. It would just have been a tad better if I had both. I'm not wanting to have to pay shipping for an additional part when the door works satisfactorily as it is.

As to the comments on how to do it....I took none of them. I (instead) removed the top hinge, and lifted to door off. I did have to have assistance to get the hole in the door aligned with the post, but that was rather easily done.

Would I do it again.....in a heart beat. I feel that I've save on the repair man making a call at the house, and experience has had me charged $60-$100 for virtually the same amount of service. My cost...shipping and all was under $20.00
Was this helpful?
Thank you for voting!
Door would close by its self.
1 person found this instruction helpful.
  • Kurt from Aurora, IN
  • Easy
  • 15 - 30 mins
  • Nutdriver
After reading the stories here, I purchased one door closing cam. After getting into the problem area, I realized I needed 2 cam, so I put the door back together and ordered another cam. If you have this problem, buy 2 cams.
Was this helpful?
Thank you for voting!
Old hinge washer worn out.
1 person found this instruction helpful.
  • James from Lockport, IL
  • A Bit Difficult
  • 15 - 30 mins
  • Socket set
First I placed a 2x4 under the frig door to keep it in place while I removed the hinge on the bottom of the door. I removed two screws holding the hinge and one screw holding the washer in place. I also loosened a screw adjacent to the washer so that I could more easily remove and replace the washer. The parts went in easily. The repa ir took much less time than I anticipated.
Was this helpful?
Thank you for voting!
Door would not close due to broken closing cam
1 person found this instruction helpful.
  • Donnette from Flagstaff, AZ
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers, Socket set
First, I was glad I read other posts on this repair as I would have only purchased one of the replacement cams when I needed two! I removed the top door hinge with a screw driver (cover) and small socket set for the door hinge. I then removed the door and removed the bottom hinge (socket set). The bottom hinge had a small rivit that held the bottom cam in place. I used a hack saw to cut off the rivit and replace the cam and secured it with a small machine bolt and nut. I then laid the door on its side and removed the top am from a bracket attached to the bottom of the door. I relaced the cam (second one) and reinserted the screws. I reattached the bottom hinge and then placed the door on the bottom hinge pin. I then held the door in place while inserting the top hinge pin bracket into place and retightening the top screws. I replace the cover with a screw drive which was the ahrdest part in trying to find the hole the small screw gets inserted into. DONE!
Was this helpful?
Thank you for voting!
Door had sagged, wouldn't close well.
2 of 4 people found this instruction helpful.
  • Brian from Louisville, KY
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers
At first, I noticed the refrigerator door didn't close at the same level of the freezer door. I started to adjust the hinges and noticed a chewed up black 'washer' at the base of the door hinge. Ppartselect.com was awesome, in that I easily found the schematic of my fridge, and the part I needed. Ordering was a snap, and it came to the house pretty quickly.
Installation, first raise the door up as high as you can, then scotch it with wood blocks (closed door). This takes the pressure off the bottom hinge you must remove.
Taking the hinge off is a snap, but then the problem presented itself. The old door closing cam was riveted to the hinge. I couldn’t get the old one off! I ended up taking it to the garage and breaking out the Dremmel tool with the abrasive cutter (the one that will cut through nails. I ended up cutting off the rivet. This was a pain.
I then found a small nut/bolt and put the new piece on, then put it back into place and removed the blocks. Works good as new. The toughest part by far was getting the old cam off… but there may be some easier way to get the rivet out that I’m not aware of.
Good luck.
Was this helpful?
Thank you for voting!
Door would not stay closed
1 person found this instruction helpful.
  • Jennifer from Holt, MO
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
BUY TWO CAMS! Just like the others, both of the cams were shot. My husband & I did this ourselves & have NEVER attempted appliance repair before.
We propped the door up high enough to access the bottom hinge piece on the fridge & removed using socket. Removed the cover from the top hinge. Slid door down off the top hinge in able to g et to the cam on bottom of door. Replaced this cam 1st in order to get door back on while worked to get the old cam off hinge. As others posted, this is rivited on. Used grinder to grind off rivit & hammer & punch to punch out. Attached new cam with bolt & nut found in our tin of leftovers. Inserted hinge into door & reattached to fridge. DONE! Not hard at all & didn't even argue the whole time.
Was this helpful?
Thank you for voting!
Fridge wasn't cooling and half freezing
1 person found this instruction helpful.
  • Wendell Hayes from Dillob, SC
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Part was perfect fit .Removed fan .three screws.replaced that s it
Was this helpful?
Thank you for voting!
Had a 'ticking' sound
1 person found this instruction helpful.
  • John from PARKVILLE, MO
  • Easy
  • 30 - 60 mins
  • Socket set
Separately (from a different site) purchased new compressor fan and motor. I purchased the grommets here because the other site listed the grommets as temporarily out of stock. I did watch one of the videos on PartSelect about the grommet replacement. Repair was pretty simple, biggest challenge was getting to the screw on the far side o f the motor. Removed the two screws holding the fan motor into place. Removed motor and blade. Reinstalled with new fan blade, new grommet and new motor.
Was this helpful?
Thank you for voting!
All Instructions for the 3976
121 - 135 of 489