38H- Maytag Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Replace the oven Sensor
3 of 5 people
found this instruction helpful.
-
Michael from Exeter, NH
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
The sensor is mounted in the top right side of the oven.An extra long screw driver helps to avoid damage to the sensor when replacing it.The connectors were the opposite to the old sensor and I did not see that there were adapter cables included. It might help to connect or tie these together as I only expected the sensor and did not loo
... Read more
k for adapters.I had cut the wires and used wire nuts when I found the adapters.The repairs works fine.
Mike
Mike
Read less
Was this helpful?
Thank you for voting!
Cooling fan runs fault code displayed
2 of 2 people
found this instruction helpful.
-
FRANK from CLARENCE CTR, NY
- Easy
- 30 - 60 mins
-
Screw drivers
Removed the two screws holding the sensor to the rear oven wall. pulled out sensor wire. It was caught on other wires behind the oven. removed the three screws holding the 8" inspection plate in the center of the rear panel. Carefully move the insulation and reach in to grasp the back end of the sensor wire. Once free from the snag it eas
... Read more
ily pulls out with the sensor just as stated in the video. using the appropriate adaptor it was easy to re-asseble and and attach to the oven wall. Replace the rear panel with the three screws and it was done
Read less
Was this helpful?
Thank you for voting!
After cleaning, F1-1 error flashed and neither oven worked
3 of 5 people
found this instruction helpful.
-
Georgene from Rock City, IL
- Easy
- 15 - 30 mins
-
Screw drivers
First I called a repairman and left a message. That was 3 weeks ago. So, I 'googled' the error message and determined what part I thought I needed. Ordered the part on Wednesday evening and it was there when I got home from work on Friday. I unpacked the part, got a phillips screwdriver and then watched the repair video on your websit
... Read more
e. About 20 minutes later I pushed my stove back in place and the flashing said 'set time'. Then I checked both ovens, and have since used both, and everything works!!
Read less
Was this helpful?
Thank you for voting!
Inside was missing
2 of 2 people
found this instruction helpful.
-
maria from MANTECA, CA
- Really Easy
- 30 - 60 mins
Great I can bake now
Was this helpful?
Thank you for voting!
Maytag range had "F3" code display, oven would not work.
2 of 2 people
found this instruction helpful.
-
phillip from Farmington, NM
- Difficult
- More than 2 hours
-
Nutdriver, Screw drivers
Oven sensor replacement was easy. Thermistor was installed in less than 15 minutes. After installation STILL had "F3" error message. Harness was ok, "Clock" or ECU needed to be replaced. "Computer" is obsolete, no spares available, some companies will rebuilt for $400+. Since the stove was going to the landfill I had nothing to lose
... Read more
by taking the "Clock" apart. It has one chip that is probably the power supply and control chip, another chip is an EEPROM with 128 bytes of storage and the last is a darlington chip that controls the relays. Cleaned up everything that looked like it needed cleaning with alcohol. When I reassembled the unit the pins for the thermistor harness felt loose, so I took it apart, again, and found cold solder joints on all four pins. It must have been there all along but plugging and unplugging the harness finally broke out the solder so I could see it. Soldered the pins back in and now it all works. It's worth a try if you're getting the "F3" message. If the relays on your stove aren't working it would be a good idea to replace the darlington chip. Good luck.
Read less
Was this helpful?
Thank you for voting!
Frayed and exposed receptical wires in cartridge
2 of 3 people
found this instruction helpful.
-
Richard C from San Jose, CA
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
* Do not lose the supplied CERAMIC electric connecting nuts; they will not fry in the heat.
* Unplug the heating elements from the old receptacles, and remove any rings; unplug the cartridge by lifting up the back side and pulling gently toward the back of the stovetop.
* Unscrew the cartridge top from the cartridg ... Read more e base (about 12 screws) and the recepticals, and cut the old wire close to the old receptacle.
* If you have a spare magnetic thingy around, use it to hold the screws and not lose them.
* Screw in the new receptacles, route the newer wiring from the receptacles (use as much of the new wire as possible), back toward the wiring block on the cartridge plug.
* Recut the old wiring to accomodate the length of the new wiring, but leave at least 2-3" from the wiring block, if possible. Re-connect them using only the supplied CERAMIC electric nuts.
* The CERAMIC nuts allayed my fears about the effect of heat on a plastic nut; ceramic is designed for high-heat environments.
* Reverse the disassembly steps to reassemble and reinstall the cartridge.
* Unplug the heating elements from the old receptacles, and remove any rings; unplug the cartridge by lifting up the back side and pulling gently toward the back of the stovetop.
* Unscrew the cartridge top from the cartridg ... Read more e base (about 12 screws) and the recepticals, and cut the old wire close to the old receptacle.
* If you have a spare magnetic thingy around, use it to hold the screws and not lose them.
* Screw in the new receptacles, route the newer wiring from the receptacles (use as much of the new wire as possible), back toward the wiring block on the cartridge plug.
* Recut the old wiring to accomodate the length of the new wiring, but leave at least 2-3" from the wiring block, if possible. Re-connect them using only the supplied CERAMIC electric nuts.
* The CERAMIC nuts allayed my fears about the effect of heat on a plastic nut; ceramic is designed for high-heat environments.
* Reverse the disassembly steps to reassemble and reinstall the cartridge.
Read less
Was this helpful?
Thank you for voting!
Oven Temperature was 50 degrees low
2 of 3 people
found this instruction helpful.
-
Eugene from Clinton, IA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Took screws out of the back on the side the sensor was on, unplugged it & took out the two screws on the inside of the oven to release the sensor. Put new sensor in place with the two screws & used one of the adapters to plug in the new sensor. Put screws back in the back panel & turned on the oven which unfortunately is still 50 degrees
... Read more
low. Need a new clock with computer which is out of stock & unavailable. I was an electrician for 25 years so didn't experience any problems. It was a cheap thing to try.
Read less
Was this helpful?
Thank you for voting!
No temperature control
2 of 3 people
found this instruction helpful.
-
Max from Houston, TX
- Easy
- 30 - 60 mins
-
Screw drivers
Turned off breakers to oven. Removed two screws that held oven in cabinet. Removed oven door by opening slightly and pulling up on door. Pulled oven out 1/3 of way. Took out four screws on top of control panel. Took oven light switch off by unscrewing holding ring. Removed temp knob on right by pulling. Removed start / stop knob same way.
... Read more
Removed glass straight out. Removed four screws that held elecrtonic clock conrtol board. Unpluged three wire plug from right side and the nine wire plug from the left side. Worked board out at and angle. Went backwards to connect and replace board, screws and door.Slid oven back in and tested oven after turning breakers back on, worked like new.
Read less
Was this helpful?
Thank you for voting!
Element in oven would not adjust to the oven temperature.
1 person
found this instruction helpful.
-
Dolores from Edmond, OK
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
I ordered the temperature sensor after watching the video and seeing how easily it could be changed out. Unfortunately, they don't tell you that it may be necessary to access the part from the back. When I tried removing the sensor from inside the oven the connection separated before getting to the hole. I tried for 4 days to try to fi
... Read more
sh out the other end. Finally, I had my brother help me remove the oven from the wall and take the back off at which time we were able to connect the new sensory. It turns out that the wiring is on the upper right hand corner of the oven and the sensor is on the upper left hand corner and the wiring is rather short. I am a 64 year old female and do the majority of repairs around the house myself, but due to the weight of removing the oven I enlisted the help of my brother. After removing from the wall the rest was a breeze. Just wish the videos or written info on the website was a little more clear as to the different ways of accessing the damaged part.
Read less
Was this helpful?
Thank you for voting!
Oven temperature fluctuates
1 person
found this instruction helpful.
-
Larry from SOLON, IA
- Easy
- 30 - 60 mins
-
Screw drivers
Replaced the thermostat according to existing videos and had to adjust the thermostat using instuctions in the user manual for model CWE4800ACB.
Was this helpful?
Thank you for voting!
Drip Pans were stained and burned on.
1 person
found this instruction helpful.
-
Sandra Collignon from SANTA CLAUS, IN
- Really Easy
- 30 - 60 mins
Replaced drip pan. Notch did not want to match the burner notch. Was a close fit bit with a little pressure made it work.
Was this helpful?
Thank you for voting!
Jennair cooktop with coils lost one of its coil guides.
1 person
found this instruction helpful.
-
Bruce from SOUTHBURY, CT
- Really Easy
- 30 - 60 mins
-
Socket set
We bought the replacement Ceramic plug and wires, and opened up the jennair cooktop piece and rewired the NEW coil guide into the system. It works great.
Was this helpful?
Thank you for voting!
burner receptacle failed (stove over 30 years old)
1 person
found this instruction helpful.
-
BETH from COUNCE, TN
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Took out burner (pulls out) Took out one screw that holds recep. in, cut the two old wires and attached new wires with wire nuts included in the new package.
Was this helpful?
Thank you for voting!
Oven door was locked, couldn't set oven temps
1 person
found this instruction helpful.
-
William from Nashville, TN
- Easy
- 15 - 30 mins
-
Screw drivers
Got a bent metal coathook to temporarily release the oven door, removed the screws from the old probe, inserted the new one, and hooked it up, using the one of the plug adapters provided. Problem solved! The oven door latch was now disengaged, the oven would now accept temperature inputs, and the rear cooling fan (which wouldn't shut off)
... Read more
now turned off. That's a lot of things working better for less than $50!
Read less
Was this helpful?
Thank you for voting!
"F3" error message and no oven heat
1 person
found this instruction helpful.
-
Pat from PAYSON, AZ
- Very Easy
- 15 - 30 mins
-
Screw drivers
Unplugged the range, removed screws holding the old sensor. When I pulled it out, the wire connecting to the sensor was completely broken through,therefore I could not just pull the wire to get to the connector. Unscrewed one side of back panel to access the connector. Pushed the connector and wire of the new sensor through the hole ( and
... Read more
behind the insulation), disconnected the old sensor and connected the new one. Re screwed the new connector in place plus rescrewed the back panel. Plugged the range in and - Viola! Everything now works like a charm and I have my oven back. Easy-Peasy. Oh - I am an older female with very limited DYI experience. I just saved myself $650.00!
Read less
Was this helpful?
Thank you for voting!