38H- Maytag Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
burner fell apart
5 of 7 people
found this instruction helpful.
-
Barbara a from Huntington, NY
- Really Easy
- Less than 15 mins
Plugged in the new burner, which we received in one day.We were delighted with the quick service
Was this helpful?
Thank you for voting!
Burner no longer worked.
4 of 5 people
found this instruction helpful.
-
Marcus from Emmett, KS
- Easy
- Less than 15 mins
-
Screw drivers
First I removed a screw that held the element in place then disconnected the two wires . Then I just reattached the two wires put the screw back in place and was done in about 10 minutes. Fairly easy fix, I had this go out a few years ago and had a repairman fix it, and saw how easy it was, so this time I did it myself. Easy job!!
Was this helpful?
Thank you for voting!
Oven was not correctly heating to set temperature
4 of 5 people
found this instruction helpful.
-
Trace from Ofallon, MO
- Really Easy
- Less than 15 mins
-
Nutdriver
Removed the approximatly 10 screws that hold on both the upper and lower pieces of sheet metal that cover the back of the oven. Removed the screw holding in the temp sensor. Unplugged and removed the old sensor. Plugged in and installed the new sensor (using one of the included adapter wires supplied with the sensor). Put the 2 pieces
... Read more
of sheet metal back on and plugged in the oven.
Read less
Was this helpful?
Thank you for voting!
Both burners were faulty, neither would come on or heat up.
3 of 3 people
found this instruction helpful.
-
Rex from Keyser, WV
- Very Easy
- Less than 15 mins
Simple, just pull out old burners and slide new ones in place. Tried both, they work excellent!
Other Parts Used:
Was this helpful?
Thank you for voting!
The burners were old and did not fit well on the stove
3 of 3 people
found this instruction helpful.
-
Karen from OLNEY, MD
- Very Easy
- Less than 15 mins
I just had to pull out the old burner and straighten the prongs for the new burner and insert, The prongs of the new burner were slightly bent in shipment, but were easy to straighten with the pliers. The burners were sent in a bag and not a box -- therefore the prongs were easily bent. I was very pleased that I (73 year old lady) was a
... Read more
ble to fix my stove without a repairman. Saved $$$
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Oven erratic, not heating correctly, timer beeper sounding
3 of 3 people
found this instruction helpful.
-
Dave from SANTA BARBARA, CA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
The video indicating •unscrew old sensor, •pull wiring, •unplug old sensor, and •plug in replacement was good until I pulled the old one and saw wire nuts behind the small square hole! After some research, I learned that the nuts COULD come through that small hole with use of needle nose pliers. One of the wire nuts had the edges pinched
... Read more
off (chipped) in the process. Then I learned about ceramic wire nuts, which I'd never previously encountered. Very important if you don't want to melt your nuts! I cut and stripped the end of a disconnect plug to the stove wiring and now I have a plug in place; which, hopefully, I'll never need to use.
Read less
Was this helpful?
Thank you for voting!
Burned up oven door gasket needed replaced.
7 of 15 people
found this instruction helpful.
-
Daniel from Prescott, MI
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers, Wrench (Adjustable)
I started by removing the door, then trying to remove all of the screws in the oven casing. Of course the very middle screw in the bottom of the oven was rusted and dammged by use. I had to use a drill bit and remove the old screw. After dissasembly of the oven casing, I found that the lip that supports the gasket was rusted and burnt awa
... Read more
y about 3/4 in. I placed the new gasket in and found that when closed it covered this defect and sealed. I reassembled and cheked for operation.Ok! Imortant--remove the elements before removing oven casing.
Read less
Was this helpful?
Thank you for voting!
Burner wouldn't heat (wiring failure)
3 of 4 people
found this instruction helpful.
-
Eugene from San Antonio, TX
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers, Wrench set
1. Shut the breaker off; Jenn-Air's design will have you working around hot leads if you don't.
2. Raise the control panel
3. Remove burner and unscrew the burner connector; trace the wires back to the control panel bottom and remove them
4. On the replacement connector, add the electrical for the control panel. These ... Read more are not included and can be found at any hardware store; they are a standard size.
5. Connect the new wires and put everything back together.
6. Reset the break and test.
2. Raise the control panel
3. Remove burner and unscrew the burner connector; trace the wires back to the control panel bottom and remove them
4. On the replacement connector, add the electrical for the control panel. These ... Read more are not included and can be found at any hardware store; they are a standard size.
5. Connect the new wires and put everything back together.
6. Reset the break and test.
Read less
Was this helpful?
Thank you for voting!
ovens wouldn't maintain temperature after preheat cycle
3 of 4 people
found this instruction helpful.
-
sherri from elk horn, IA
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
unplugged oven. removed 2 screws that hold the sensor in place, then removed the dozen or so screws that hold on the rear panel, unplugged sensor and fed wire through insulation. identified and installed correct harness adapter then fed new wire and connecter through insulation and connected to adapter. installed sensor retaining screws.p
... Read more
lugged oven back in and tested function.no dice. unplugged oven once again. removed oven control panel and upon inspection of printed circuit board discovered 3 solder joints had failed. dang. resoldered failed joints and also sweetened up a few others that looked suspect. reinstalled controller, replaced all retaining hardware, and plugged in the oven. tah-dah!! works like a charm now. moral of the story is check the pc board first and save $50 for unneeded pats!!! or buy the controller from parts direct for $260ish. btw a roll of solder and soldering iron from an auto parts store cost around $10, learned to solder on you-tube $0. amazing all the home appliances yo can fix if you're not afraid to take a few screws out and poke around a bit. CHEERS!
Read less
Was this helpful?
Thank you for voting!
Burners weren't heating
3 of 4 people
found this instruction helpful.
-
james from killingworth, CT
- Really Easy
- Less than 15 mins
Unplugged old burner elements. Popped in new burners. Turned on the burners to test.
Was this helpful?
Thank you for voting!
burner would not stay heated had to wiggle the burner to make heat
3 of 4 people
found this instruction helpful.
-
Marjorie from Swanton, MD
- Really Easy
- Less than 15 mins
Replaced with the new burner works like new. Thanks a bunch!
Was this helpful?
Thank you for voting!
Electric Stove Burner was working unreliably
3 of 5 people
found this instruction helpful.
-
Jacqueline from Austin, TX
- Really Easy
- Less than 15 mins
pulled out the old burner, plugged in the new burner. Turned on the power and it heated up very quickly.
Was this helpful?
Thank you for voting!
The larger burners would stop working while in use.
2 of 2 people
found this instruction helpful.
-
Lisa from PORT JEFF STA, NY
- Very Easy
- Less than 15 mins
The removal of the old burner and installation of the new burners was easy. Just lift the opposite side that rests on the rim and pull burner out. New burner then gets inserted and the opposite side goes right into rim. It took all of 30 seconds to replace both burners. I wish I had replaced these when they first started to go!!
Was this helpful?
Thank you for voting!
Oven would over heat and produce a F2 error code on the display. It would not turn off or cool down until I switched the circuit breaker off.
2 of 2 people
found this instruction helpful.
-
richard from SAINT MARYS, KS
- Very Easy
- Less than 15 mins
-
Screw drivers
I switched the oven sensor easily enough, but it did not remedy the problem, so we are in the process of replacing the oven since it's about 20 yrs. old.
Was this helpful?
Thank you for voting!
Oven would not heat
2 of 2 people
found this instruction helpful.
-
francis from mount holley, VA
- Really Easy
- Less than 15 mins
-
Screw drivers
Spoke to your very helpful staff, who advised me that a likely problem was the oven sensor. I took a chance and ordered the part, which came promptly. Your service video for the part was most helpful in my decision to try the part. Installation was a breeze, but it was the oven controller board that had failed and not the oven sensor.
... Read more
That called for a service professional, who ultimately fixed the problem. Your service though, was excellent and I would highly recommend you to others.
Read less
Was this helpful?
Thank you for voting!