EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

38FY Magic Chef Range - Instructions

All Instructions for the 38FY
121 - 135 of 330

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Burnt out
2 of 4 people found this instruction helpful.
  • David from Elba, AL
  • A Bit Difficult
  • 15 - 30 mins
  • Pliers, Screw drivers
All went well except for error on instruction sheet.
Ground wire used on earlier Models attached to the ground lug is no longer used?? and should be removed!!! Guess what the ground wire has to be used or the element will not heat up.Soooo someone at the mfg. has no ideal what they are talking about,You have to ground the element or it will not come on.
Was this helpful?
Thank you for voting!
Half of broiler element worked
1 person found this instruction helpful.
  • Paul from SEATTLE, WA
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
Turned off power at panel. Removed 2 Phillips screws holding broiler element support in place. Squirted 2 additional Phillips head screws attaching element to back of stove with WD-40 and removed screws. Slid element out to access electrical connection and used short phillips screwdriver to remove. Reattached electrical connection to new element with short screwdriver (no fun as you are cantilevered into the oven and have to hold the element, the screw and the screwdriver to do this). Slid element into support and screwed support to top of stove cavity to align element. Installed screws holding element onto back wall. Turned on power and ran element long enough to dissipate WD-40 fumes.
Was this helpful?
Thank you for voting!
Element in oven would not adjust to the oven temperature.
1 person found this instruction helpful.
  • Dolores from Edmond, OK
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
I ordered the temperature sensor after watching the video and seeing how easily it could be changed out. Unfortunately, they don't tell you that it may be necessary to access the part from the back. When I tried removing the sensor from inside the oven the connection separated before getting to the hole. I tried for 4 days to try to fi sh out the other end. Finally, I had my brother help me remove the oven from the wall and take the back off at which time we were able to connect the new sensory. It turns out that the wiring is on the upper right hand corner of the oven and the sensor is on the upper left hand corner and the wiring is rather short. I am a 64 year old female and do the majority of repairs around the house myself, but due to the weight of removing the oven I enlisted the help of my brother. After removing from the wall the rest was a breeze. Just wish the videos or written info on the website was a little more clear as to the different ways of accessing the damaged part.
Was this helpful?
Thank you for voting!
Drip Pans were stained and burned on.
1 person found this instruction helpful.
  • Sandra Collignon from SANTA CLAUS, IN
  • Really Easy
  • 30 - 60 mins
Replaced drip pan. Notch did not want to match the burner notch. Was a close fit bit with a little pressure made it work.
Was this helpful?
Thank you for voting!
Jennair cooktop with coils lost one of its coil guides.
1 person found this instruction helpful.
  • Bruce from SOUTHBURY, CT
  • Really Easy
  • 30 - 60 mins
  • Socket set
We bought the replacement Ceramic plug and wires, and opened up the jennair cooktop piece and rewired the NEW coil guide into the system. It works great.
Was this helpful?
Thank you for voting!
F5 fault code kept appearing
1 person found this instruction helpful.
  • Louis Rodriguez from Granbury, TX
  • Very Difficult
  • More than 2 hours
  • Nutdriver, Screw drivers
I installed the new oven sensor but the problem continued. So I ordered a new relay board and installed it. Still no luck. So I pulled the new board back out and started trouble shooting it using my electronic background. I discovered the new board was using a pin for L2 that had no exit on the backplane, so I removed it and installed it where I believed it should go. Reinstalled the power relay board and presto. My oven is working lie a champ. Louis
Was this helpful?
Thank you for voting!
Burner plugs were loose
1 of 2 people found this instruction helpful.
  • James from CONCORD, NC
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
used the supplied parts...very easy. The parts were exact replacements.
Was this helpful?
Thank you for voting!
Oven not heating to desired temp
2 of 5 people found this instruction helpful.
  • Raymond from Ridgecrest, CA
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Screw drivers
Had to remove oven from mounting cabinet to get to the back since the wire lenght to the conector was to short to come through the mounting hole.
Other than that the repair was straight forward. 4 screws to dismount the Oven from cabinet, 2 screws to remove Sensor and 3 srews to open the back of the oven once out in the open. New cab le adapter that came with the new sensor was needed in my case.
Was this helpful?
Thank you for voting!
Oven would not heat
1 of 2 people found this instruction helpful.
  • Ralph from Nicholasville, KY
  • Easy
  • 30 - 60 mins
  • Screw drivers
Flipped off breaker and removed oven door and pulled built in stove out so the back panel could be removed. Unplugged the sensor then removed the two screws securing the old sensor inside the oven and installed new sensor. Put stove back together and installed back into counter top, re-installed oven door, flipped on the breaker and ove n works like new.
Was this helpful?
Thank you for voting!
F1-1 and F3-1 error code
2 of 5 people found this instruction helpful.
  • Barbara from Lakeville, MA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Very easy to repair, but you have to be able to pull your stove out. Two screws in the oven and then remove part of back cover of oven and one plug from there. Simple to do, but did not fix our problem. We are waiting repair now from service company as it looks like it needs a control panel. Worth trying yourself to fix the problem. Inexpensive part and easy to install. Also be sure to turn power off your oven to reset the control panel as this may fix the problem - try this first and also after installing new part - like rebooting a computer...
Was this helpful?
Thank you for voting!
Oven Over Heating
1 of 2 people found this instruction helpful.
  • Steve from New Albany, OH
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Removed the oven from the wall. Removed back cover and unplugged sensor from the harness. Remove and replace sensor from inside the oven. Reconnect harness and reinstall back cover. Secure oven back into the wall.
Was this helpful?
Thank you for voting!
burned out stove eye, 6"
1 of 2 people found this instruction helpful.
  • Robert from Birmingham, AL
  • Easy
  • 15 - 30 mins
remove burned out eye, replaced with new eye.new eye does not fit exactally correct onto splash pan as point on end of steel " rod " not pointed enough to slip into mate on splash pan
Was this helpful?
Thank you for voting!
my stovetop light did not work
1 of 2 people found this instruction helpful.
  • Geraldine M. from Fork Union, VA
  • Really Easy
  • 15 - 30 mins
We actually had to get the repairman back that had repaired our microwave. Our range has the attached microwave above the range. My stovetop light worked prior to the visit. When he left, I prepared supper without the light, which did not go on. Ultimately, we had to replace the fluorscent tube, which thankfully, you had. No applianc e store in a 35 mile radius did. We finally got the glass protector off, and the new tube did not go on. Back to the repairman, to tell him the new bulb did not work and that probably something happened when he visited before. He came back, found that indeed a wire had been broken when he was working on the microwave. I had indicated to him I did not expect to pay another repair bill after I had alrealy spent 117. before plus the cost of the new bulb, 22. something including shipping. He obliged and id not charge me anythink to repair the broken wire.
Now I have the old bulb for back up!!!
Thank you for having my replacement tube!!
Was this helpful?
Thank you for voting!
Broiler element broken
1 of 2 people found this instruction helpful.
  • Walter J from Boynton Beach, FL
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Very simple, unscrew the old element. Remove the electrical spade connectors and reverse to install new element. The folks at parts select.com were very helpful and even after I ordered the wrong part, the return process was hassle free. Prompt shipping, very happy.
Was this helpful?
Thank you for voting!
Top oven element works, but bottom element works only intermittently
2 of 5 people found this instruction helpful.
  • Bruce from Glencoe, MN
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Replaced the long Oven Sensor but have not resolved the root problem. Oven still will not reach required temperature. Bottom element becomes red hot, but turns off and will not start again.
Was this helpful?
Thank you for voting!
All Instructions for the 38FY
121 - 135 of 330