38FY Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
No temperature control
2 of 3 people
found this instruction helpful.
-
Max from Houston, TX
- Easy
- 30 - 60 mins
-
Screw drivers
Turned off breakers to oven. Removed two screws that held oven in cabinet. Removed oven door by opening slightly and pulling up on door. Pulled oven out 1/3 of way. Took out four screws on top of control panel. Took oven light switch off by unscrewing holding ring. Removed temp knob on right by pulling. Removed start / stop knob same way.
... Read more
Removed glass straight out. Removed four screws that held elecrtonic clock conrtol board. Unpluged three wire plug from right side and the nine wire plug from the left side. Worked board out at and angle. Went backwards to connect and replace board, screws and door.Slid oven back in and tested oven after turning breakers back on, worked like new.
Read less
Was this helpful?
Thank you for voting!
Frayed and exposed receptical wires in cartridge
2 of 3 people
found this instruction helpful.
-
Richard C from San Jose, CA
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
* Do not lose the supplied CERAMIC electric connecting nuts; they will not fry in the heat.
* Unplug the heating elements from the old receptacles, and remove any rings; unplug the cartridge by lifting up the back side and pulling gently toward the back of the stovetop.
* Unscrew the cartridge top from the cartridg ... Read more e base (about 12 screws) and the recepticals, and cut the old wire close to the old receptacle.
* If you have a spare magnetic thingy around, use it to hold the screws and not lose them.
* Screw in the new receptacles, route the newer wiring from the receptacles (use as much of the new wire as possible), back toward the wiring block on the cartridge plug.
* Recut the old wiring to accomodate the length of the new wiring, but leave at least 2-3" from the wiring block, if possible. Re-connect them using only the supplied CERAMIC electric nuts.
* The CERAMIC nuts allayed my fears about the effect of heat on a plastic nut; ceramic is designed for high-heat environments.
* Reverse the disassembly steps to reassemble and reinstall the cartridge.
* Unplug the heating elements from the old receptacles, and remove any rings; unplug the cartridge by lifting up the back side and pulling gently toward the back of the stovetop.
* Unscrew the cartridge top from the cartridg ... Read more e base (about 12 screws) and the recepticals, and cut the old wire close to the old receptacle.
* If you have a spare magnetic thingy around, use it to hold the screws and not lose them.
* Screw in the new receptacles, route the newer wiring from the receptacles (use as much of the new wire as possible), back toward the wiring block on the cartridge plug.
* Recut the old wiring to accomodate the length of the new wiring, but leave at least 2-3" from the wiring block, if possible. Re-connect them using only the supplied CERAMIC electric nuts.
* The CERAMIC nuts allayed my fears about the effect of heat on a plastic nut; ceramic is designed for high-heat environments.
* Reverse the disassembly steps to reassemble and reinstall the cartridge.
Read less
Was this helpful?
Thank you for voting!
Oven did not heat up in bake mode.
2 of 3 people
found this instruction helpful.
-
Peter from Westcliffe, CO
- Easy
- 30 - 60 mins
-
Screw drivers
The ignitor heated up and the broiler worked but not the bake mode. Repaired per instructions
Was this helpful?
Thank you for voting!
Replace clock-adjust knob
2 of 3 people
found this instruction helpful.
-
OSCAR from BRISTOL, CT
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers
Although normally a push fit, we drilled and tapped a #6-32 cross hole and used a set-screw to attach the small knob.
The original knob is still hiding somewhere but, thanks to PartSelect we are back in business !
The original knob is still hiding somewhere but, thanks to PartSelect we are back in business !
Was this helpful?
Thank you for voting!
Replaced Broiler Element
2 of 3 people
found this instruction helpful.
-
Phillip from Reston, VA
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Turned off oven power.Removed oven heat shield, element support clips and element mounting plate screws. Disconnected three element power wires and ground wire. Removed old element. Reversed removal procedure for new element install. Piece of cake.
Was this helpful?
Thank you for voting!
F 3 signal on display pad every time oven warmed up
2 of 3 people
found this instruction helpful.
-
jeff from haskell, NJ
- Easy
- 15 - 30 mins
-
Screw drivers
Removed all the racks from inside the oven, unscrewed the 6 screws that held it into the cabinet, pulled it out and sat it on the floor in front of the cabinet. Removed the oven sensor from the inside of the oven after disconnecting the wire harness from the rear right exterior of the oven. Installed new sensor from inside (2screws), plug
... Read more
ged it into the harness in the back and reinstalled oven in the cabinet.
Read less
Was this helpful?
Thank you for voting!
Oven Temperature was 50 degrees low
2 of 3 people
found this instruction helpful.
-
Eugene from Clinton, IA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Took screws out of the back on the side the sensor was on, unplugged it & took out the two screws on the inside of the oven to release the sensor. Put new sensor in place with the two screws & used one of the adapters to plug in the new sensor. Put screws back in the back panel & turned on the oven which unfortunately is still 50 degrees
... Read more
low. Need a new clock with computer which is out of stock & unavailable. I was an electrician for 25 years so didn't experience any problems. It was a cheap thing to try.
Read less
Was this helpful?
Thank you for voting!
lamp retainer gasket disintegrated when changed burned out bulb
2 of 3 people
found this instruction helpful.
-
Sandra from Flemington, NJ
- Really Easy
- 15 - 30 mins
-
Screw drivers
I just removed the lamp retainer plate and glass cover, inserted the new gasket, and screwed everything back in place. Simple as that. I was enormously pleased that the part arrived so quickly -- just in time for me to cook my Thanksgiving turkey and use the self-cleaning feature.
Was this helpful?
Thank you for voting!
Had an F2 message go off then F3 when I tried to turn the stove on
2 of 3 people
found this instruction helpful.
-
Daniel from MOUNT HEALTHY, OH
- Very Easy
- Less than 15 mins
-
Screw drivers
Unplugged the old temp sensor at the back of the stove. From the inside I removed the 2 retaining screws. I taped a string to the old wire and pulled it through so I could pull the new harness through on the new sensor. When the new sensor arrived I installed it in reverse order. Easy peasy. Works great!!!!
Was this helpful?
Thank you for voting!
Used part
2 of 3 people
found this instruction helpful.
-
Sabrina from FREMONT, CA
- Very Easy
- Less than 15 mins
Lift burners out of plug discard old drip pans replace new drip pans into plugs and done .
Other Parts Used:
Was this helpful?
Thank you for voting!
I needed a broiler pan
4 of 9 people
found this instruction helpful.
-
Rhoda P. from Secaucus, NJ
- Really Easy
- Less than 15 mins
I took the broiler pan out of the shipping container and put it in the oven.
Other Parts Used:
Was this helpful?
Thank you for voting!
surface element needed to be replaced along with all the drip Bowls
2 of 4 people
found this instruction helpful.
-
Tawnia from SHOW LOW, AZ
- Really Easy
- Less than 15 mins
take out the old put in the new
Other Parts Used:
Was this helpful?
Thank you for voting!
burner would not heat.
1 person
found this instruction helpful.
-
Jackie from Hughes Springs, TX
- Really Easy
- Less than 15 mins
I unpluged the old burner and pluged the new one in. Repair done in about 2 min,
Was this helpful?
Thank you for voting!
The heating element on the left front burner was out
2 of 4 people
found this instruction helpful.
-
Julie from Salt Lake City, UT
- Really Easy
- Less than 15 mins
Pulled the old one out and plugged the new one in. It was that simple!
Was this helpful?
Thank you for voting!
oven not heating to set temp. 100 degrees too cold
2 of 4 people
found this instruction helpful.
-
Robert from Funston, GA
- Really Easy
- Less than 15 mins
-
Screw drivers
installed part,turned unit on-temp still cold. reset digital control, up 35 degrees, still cold. un-plugged unit,re-connect after 10 min. still cold.
Was this helpful?
Thank you for voting!