38FY Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Couldn't find correct drip bowls that fit.
2 of 4 people
found this instruction helpful.
-
Lowell from Hardin, KY
- Really Easy
- Less than 15 mins
Removed old drip bowls, removed burners installed new drip bowls,installed burners. They fit perfect and I received them two days after ordering.
Other Parts Used:
Was this helpful?
Thank you for voting!
The old drip bowls were rusting, no chrome left
3 of 7 people
found this instruction helpful.
-
kathryn from piqua, OH
- Really Easy
- Less than 15 mins
Took the old ones out and put in the new ones! What I am so pleased about it that I just went online and at Parts Select website it was easy to find what I needed, a fair price and the 4 bowls arrived within 2 days!
Other Parts Used:
Was this helpful?
Thank you for voting!
2 Service Elements Didn't Work (Didn't heat up)
1 person
found this instruction helpful.
-
Roseann from MEADVILLE, PA
- Very Easy
- Less than 15 mins
Unplugged old elements and plugged in new ones
Other Parts Used:
Was this helpful?
Thank you for voting!
ELECTRIC BURNER SUPPORT FELL OFF AND BURNER SOMETIMES WOULD NOT COME ON.
1 person
found this instruction helpful.
-
RICHARD from SHOW LOW, AZ
- Very Easy
- Less than 15 mins
Stuck the new one into the plugin.
Was this helpful?
Thank you for voting!
No problem installing the sensor
1 person
found this instruction helpful.
-
tommy from FAYETTEVILLE, NC
- Very Easy
- Less than 15 mins
-
Screw drivers
I removed the two mounting screws and pulled the harness through the opening unsnapped the sensor from the harness and installed the new sensor i didn't have to used the adapters the new sensor fitted
Was this helpful?
Thank you for voting!
"F3" error message and no oven heat
1 person
found this instruction helpful.
-
Pat from PAYSON, AZ
- Very Easy
- 15 - 30 mins
-
Screw drivers
Unplugged the range, removed screws holding the old sensor. When I pulled it out, the wire connecting to the sensor was completely broken through,therefore I could not just pull the wire to get to the connector. Unscrewed one side of back panel to access the connector. Pushed the connector and wire of the new sensor through the hole ( and
... Read more
behind the insulation), disconnected the old sensor and connected the new one. Re screwed the new connector in place plus rescrewed the back panel. Plugged the range in and - Viola! Everything now works like a charm and I have my oven back. Easy-Peasy. Oh - I am an older female with very limited DYI experience. I just saved myself $650.00!
Read less
Was this helpful?
Thank you for voting!
burner receptacle failed (stove over 30 years old)
1 person
found this instruction helpful.
-
BETH from COUNCE, TN
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Took out burner (pulls out) Took out one screw that holds recep. in, cut the two old wires and attached new wires with wire nuts included in the new package.
Was this helpful?
Thank you for voting!
The oven did not heat, but the top burners worked fine.
1 person
found this instruction helpful.
-
Marvin from DECATUR, GA
- Really Easy
- 15 - 30 mins
-
Screw drivers
1. Slowly pull the stove from wall. 2. Unplug 120 volts plug from outlet. 3.Turned off the gas outlet. 4. Open the stove door, remove the racks, then unscrew (2) screws that hold the short oven sensor in place. 5. Slowly pull sensor out of it's housing. Remove the clip that holds the sensor. Install new sensor using the clip. Push sensor
... Read more
back through the hole opening. Screw the (2) screws into the mount to secure the sensor. 6. Plug the 120 volt plug into the wall outlet. Turn on the gas outlet. Test stove by turning on oven. It works like a new stove. Wife is happy, and Thanks Giving Dinner is on! Reverse your steps to secure your stove. A total of 25 minutes after cleaning the dust under stove. Thanks for everything. By the way, Thanks Giving Dinner was delicious.
Read less
Was this helpful?
Thank you for voting!
Oven would not hold temperature, not turn on, and would shut off during use.
1 person
found this instruction helpful.
-
John from Arvada, CO
- Very Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Extremely simple repair to make. Move stove away from wall and disconnect power. Remove the oven racks. Remove the rear sheet metal panel covering the wiring harnesses. Caution: Sharp edges and corners on sheet metal.Sensor is located in upper left corner on rear oven wall. Using a long-shafted #2 Philips screwdriver, remove the two Phili
... Read more
ps head screws and gently pull the sensor 1" away from the oven wall. At this point, it will help to have an assist from someone while you are behind the range. Have the assistant gently tug on the sensor while you watch for wires moving on the rear of the range. After locating the sensor wires, gently disconnect the plastic connector clip. Note: plastic connectors become brittle with age and exposure to heat Move to front of range and gently remove sensor from rear wall by pulling the wiring through the oven wall. Before inserting the new sensor wire through the oven wall, "dry fit" the wiring connectors to see that the new sensor is a correct connection. Make connection, and secure the sensor to the rear oven wall with the two screws. Install racks, reinstall rear sheet metal panel, and connect the power. Set the oven baking temperature to a moderately low temp, 300 - 350 deg. to test the new sensor.
Read less
Was this helpful?
Thank you for voting!
Oven shutting off, getting an F1 error on ECM
2 of 4 people
found this instruction helpful.
-
Ben from Belen, NM
- Really Easy
- 15 - 30 mins
-
Screw drivers
Remove rear sheet metal cover. Disconnect the temp sensor wiring connector (on the left side as viewed from front).
Open oven, take out the 2 screws attaching sensor and remove. Reverse for installation.
Included wiring adapters are not needed for this model oven.
Open oven, take out the 2 screws attaching sensor and remove. Reverse for installation.
Included wiring adapters are not needed for this model oven.
Was this helpful?
Thank you for voting!
replace element
1 person
found this instruction helpful.
-
alex from huntington, NY
- Really Easy
- 15 - 30 mins
-
Screw drivers
remove two bracket screws, and remove bracket, the remove two mount screws for element. then remove the element. installed the element in reverse order that it was removed.
Was this helpful?
Thank you for voting!
Element burned out, broke circle, heat only half
1 person
found this instruction helpful.
-
Michael from Thornton, TX
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Repair went fine, insert helped, just take your time and remember the way you took out. Started without takeing door off, I am to short and door comes off easy, unscrew the two screws holding element leaving one not quite off then the back two screws then go back to upper screw remove and element will pull out, remove 3 wires remembering
... Read more
the order, Wiring is a little tricky (in the stove-just 3 plugins), just pay attention and will go smooth. Then remove element and go backwards and presto your done.
Read less
Was this helpful?
Thank you for voting!
Oven door was locked, couldn't set oven temps
1 person
found this instruction helpful.
-
William from Nashville, TN
- Easy
- 15 - 30 mins
-
Screw drivers
Got a bent metal coathook to temporarily release the oven door, removed the screws from the old probe, inserted the new one, and hooked it up, using the one of the plug adapters provided. Problem solved! The oven door latch was now disengaged, the oven would now accept temperature inputs, and the rear cooling fan (which wouldn't shut off)
... Read more
now turned off. That's a lot of things working better for less than $50!
Read less
Was this helpful?
Thank you for voting!
Oven temperature fluctuates
1 person
found this instruction helpful.
-
Larry from SOLON, IA
- Easy
- 30 - 60 mins
-
Screw drivers
Replaced the thermostat according to existing videos and had to adjust the thermostat using instuctions in the user manual for model CWE4800ACB.
Was this helpful?
Thank you for voting!
Broiler element was only working on one side
1 person
found this instruction helpful.
-
Helen from SPRINGFIELD, OH
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers
Grandson spent 1/2 hour installing unit and 15 minutes of that time was trying to get the very short grounded screw to begin to thread. It was a very small space to work in and it kept falling out. The instructions were a lot to be desired - almost nothing. He went to YouTube and got very explicit instructions. Then he had no problem
... Read more
as to what to do. The unit is working great now.
Read less
Was this helpful?
Thank you for voting!