3890 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
knobs were old could not read numbers
8 of 10 people
found this instruction helpful.
-
catherine from holland, MA
- Really Easy
- Less than 15 mins
knobs fit perfectly
Was this helpful?
Thank you for voting!
cook top module would not heat.
8 of 10 people
found this instruction helpful.
-
Daryl from Olathe, KS
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Screw drivers
The contact spades were burned from 10+ years of use and the cook top module was worn. I disassembled the module, taped the top to protect the creamic cook top, sanded the metal and spray painted to restore the original white finish. On the bottom half I replaced one missing pop rivet and cleaned and spray painted the bottom to restore to
... Read more
the original black. When the contact spades arrived, I replaced the contact spades and reassembled the module. It now works and looks like it did when it was new.
Read less
Was this helpful?
Thank you for voting!
light bulb in water ice freezer door went bad
8 of 14 people
found this instruction helpful.
-
Carl from RIVERSIDE, CA
- Very Difficult
- More than 2 hours
-
Screw drivers
I didn't. Don't know how to get to light bulb to change it for this specific model
Was this helpful?
Thank you for voting!
drain jar lids rusted and broken of their mounts
5 of 5 people
found this instruction helpful.
-
ronald from ESTERO, FL
- A Bit Difficult
- 15 - 30 mins
The lids are fastened to the underside of the unit by rivets....3 to each lid.
I used a cordless drill and small drill bit to drill through the rivets to remove the old lids and remains of the rivets.
The new lids are easily fastened back using a rivet gun ( about $20 in Lowes) using small 1/8th aluminum rivets.
No real pro ... Read more blems.
1 thing to note is that the drill bit will pass through the old rivet by about 1/4 inch before it comes up against the upper level of the BBQ floor so do not drill any deeper.The aluminum rivets are easy to drill through and you will easily feel when the rivet is drilled through.
I used a cordless drill and small drill bit to drill through the rivets to remove the old lids and remains of the rivets.
The new lids are easily fastened back using a rivet gun ( about $20 in Lowes) using small 1/8th aluminum rivets.
No real pro ... Read more blems.
1 thing to note is that the drill bit will pass through the old rivet by about 1/4 inch before it comes up against the upper level of the BBQ floor so do not drill any deeper.The aluminum rivets are easy to drill through and you will easily feel when the rivet is drilled through.
Read less
Was this helpful?
Thank you for voting!
The element burned out
5 of 6 people
found this instruction helpful.
-
Diane from Orlando, FL
- Really Easy
- Less than 15 mins
Just replaced the element and put new rock grate supports on the rock grates and we're set to grill
Other Parts Used:
Was this helpful?
Thank you for voting!
Reusable Grease filter was old and worn out.
5 of 7 people
found this instruction helpful.
-
Gloria from Galveston, TX
- Really Easy
- Less than 15 mins
The Model number could no longer be read clearly on the stove electric grill with a down draft vent system, so all I had was the size and looks of the old grease/air filter. I was very happy to come across Parts Select by way of an amazon.com search. Their web site's design and the parts pictures with detailed descriptions made it eas
... Read more
y to find exactly what I needed. The grease filter fit perfectly in no time. I have successfully used my cooking grill again.
Read less
Was this helpful?
Thank you for voting!
The control knobs on our otherwise "healthy" Jenn-Air range were worn off and did not turn stove on correctly.
4 of 4 people
found this instruction helpful.
-
Brad from Clay City, IL
- Really Easy
- Less than 15 mins
Simply pulled the old ones off and pressed on the new control knobs. It took less than 10 minutes, saved us from replazcing an otherwise nice looking range top, and made a big deposit in my "Honey do" account. I just wish they still sold the clock and timer units to fit this stove. Oh and yes, the prices were very reasonable too.
... Read more
Thank You Brad Harris, Illinois
Read less
Was this helpful?
Thank you for voting!
Both electric burners didn’t work
4 of 4 people
found this instruction helpful.
-
James from ROCHESTER HLS, MI
- Really Easy
- 30 - 60 mins
Problem was the neutral connector spike was burned and didn’t make good connection. Service man said he couldn’t get parts and charged $100 and left.
The neutral conductor cost about $12. And was an easy fix!
Thank you PartSelect!
The neutral conductor cost about $12. And was an easy fix!
Thank you PartSelect!
Other Parts Used:
Was this helpful?
Thank you for voting!
I spilled a pot of soup and shorted everything out had to replace these parts
6 of 11 people
found this instruction helpful.
-
William from York, PA
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers
Pulled out the burners, Freed the outside rim and removed the burnerbox with the burnned out pieces removed tham and reassembled
Other Parts Used:
Was this helpful?
Thank you for voting!
missing drip bowls
3 of 3 people
found this instruction helpful.
-
Erin from Coeur D Alene, ID
- Really Easy
- Less than 15 mins
Our stove is from 1978 and was missing all but one drip bowl. I bought all the replacement parts from all the store, (Walmart, Target, Fred Meyer) nothing fit. I finally found this site and they fit perfectly! Thank you. If I have to keep the stove a while longer at least it looks clean and new now, and it still works great!
Was this helpful?
Thank you for voting!
smell of a dead animal
3 of 4 people
found this instruction helpful.
-
Duane from Niceville, FL
- Really Easy
- Less than 15 mins
The 15-year-old Jen-Air stove started smelling really bad. I thought it was a dead animal stuck in the exhaust tube which runs under the floor to the outside. I flushed it out with clorine bleach, but it was still bad. It turned out to the be the grease filter. I washed it every week in the diswasher, but it just was not enough to get
... Read more
it clean enough. Finally, the grease went rancid and smelled really bad. This "repair" took about 30 seconds.
Read less
Was this helpful?
Thank you for voting!
old filter to replace
2 of 2 people
found this instruction helpful.
-
Colette from Baton Rouge, LA
- Really Easy
- Less than 15 mins
:-) - Just removed the old one and replace with the new one. Nothing to it. Takes 30 seconds.
Was this helpful?
Thank you for voting!
A local repair shop informed the individual that the burner unit could not be repaired and she would have to replace the cooktop..
2 of 2 people
found this instruction helpful.
-
Sonny from MOUNT VERNON, GA
- Very Easy
- Less than 15 mins
-
Screw drivers, Socket set
After examining the burner unit I noticed that one of the male contact spades was burned and look deformed. After removing the spade I discovered that it had been originally manufactured incorrectly. I went on line to try and find the part. I found it at this site . I ordered 2 of the spades and replaced the deformed spade and anothe
... Read more
r one that looked like it had gotten a little hot. She tried the unit and it worked perfectly. She had not used that burner unit for a very lengthy time. The investigation of the problem took a little time, but the repair went very fast. Moral is :" If a spade doesn't look right, it probably isn't", but either the individual spade or plug can be replaced. This site is now my "GO TO" place for parts.
Read less
Was this helpful?
Thank you for voting!
change the cartridge top to Stainless Steel
2 of 2 people
found this instruction helpful.
-
Sharon from REPUBLIC, WA
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Changing the cartridge tops over to Stainless Steel was very easy and looks good,
Was this helpful?
Thank you for voting!
Replacing the bulb in the freezer side
5 of 11 people
found this instruction helpful.
-
Yafa (and David) from Bothell, WA
- Easy
- Less than 15 mins
-
Nutdriver
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this helpful?
Thank you for voting!