3888 Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Previous element burnt up
1 person
found this instruction helpful.
-
Betsy from Sun City, AZ
- Really Easy
- Less than 15 mins
-
Screw drivers
I let my husband to the work...But it was very easy. I could have done it! He removed the screws, pulled the wires off previous element. Reattached the wires to the new element and screwed the ends back in place.
Was this helpful?
Thank you for voting!
fireworks in the oven. Burned completely in two.
1 person
found this instruction helpful.
-
Shelly from Allentown, PA
- Really Easy
- Less than 15 mins
-
Screw drivers
My husband has moved out of state for his job. I am left here with the children until the house sells. This is the first time I have ever had to do any oven repair. I had excellent and fast service - my part came right away. I took out the 2 screws holding the element in place, pulled the element out, disconnected the old element, connect
... Read more
ed the new one, pushed it back in, and replaced the screws. No problem at all. I was a little nervous turning it all back on, but it is working perfectly!
Read less
Was this helpful?
Thank you for voting!
Bake Element shorted out
1 person
found this instruction helpful.
-
Laurie from Clarence, NY
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
I first shut off the breaker to the stove - safety first!
I used a phillips screw driver to remove the two screws that held the old element in. Then I pulled the old element out and used the pliers to remove the electrical connections. I put the new element in, made the electrical connections and secured it with the screws. ... Read more After restoring powere via the breaker, we tested the stove and it worked. Just call me the Maytag Man!
I used a phillips screw driver to remove the two screws that held the old element in. Then I pulled the old element out and used the pliers to remove the electrical connections. I put the new element in, made the electrical connections and secured it with the screws. ... Read more After restoring powere via the breaker, we tested the stove and it worked. Just call me the Maytag Man!
Read less
Was this helpful?
Thank you for voting!
My oven sparked, then wasn't working, so I turned to the internet.
1 person
found this instruction helpful.
-
Joan from Medford, OR
- Really Easy
- Less than 15 mins
-
Screw drivers
I received the new element on the third day, followed simple directions, and voila! I'm baking again.
First I unplugged the stove. Important!. Then with a phillips head screwdriver I removed the two screws at the back of the oven. The transition from busted to new was easy because there was a slide-in connection to the wires, not ... Read more screws. The best advice was sticking duct tape on the wires so they wouldn't go back into the inner sanctum before I was able to attach the new element. Hey, I'm a 72-year-old grandma, and it was easy!
First I unplugged the stove. Important!. Then with a phillips head screwdriver I removed the two screws at the back of the oven. The transition from busted to new was easy because there was a slide-in connection to the wires, not ... Read more screws. The best advice was sticking duct tape on the wires so they wouldn't go back into the inner sanctum before I was able to attach the new element. Hey, I'm a 72-year-old grandma, and it was easy!
Read less
Was this helpful?
Thank you for voting!
The oven heating element burned out like a lit fuse!
1 person
found this instruction helpful.
-
Herbert from Neenah, WI
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed 2 phillips screws, unplugged 2 wires, threw away old element. Installation of the new element was just as easy but in reverse order. Piece of cake!
Was this helpful?
Thank you for voting!
Element burned in half
1 person
found this instruction helpful.
-
James from Allyn, WA
- Really Easy
- Less than 15 mins
-
Screw drivers
Took two screws out unplugged the element and plugged the new one in and replaced the screws and turned the breaker back on. Works great...Piece of cake..jk
Was this helpful?
Thank you for voting!
oven not heating to set temp. 100 degrees too cold
2 of 4 people
found this instruction helpful.
-
Robert from Funston, GA
- Really Easy
- Less than 15 mins
-
Screw drivers
installed part,turned unit on-temp still cold. reset digital control, up 35 degrees, still cold. un-plugged unit,re-connect after 10 min. still cold.
Was this helpful?
Thank you for voting!
bakeing element caught fire.
1 person
found this instruction helpful.
-
Leticia from Sunnyvale, CA
- Really Easy
- Less than 15 mins
First I turned off power to the range at the fuse box (very important-The last time I didn't do this and ended up paying a repairman $150.00 to replace the damaged connectors). I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I then connected the new ele
... Read more
ment, pushed the element back in and replaced the screws. Turned the power back on and tested the element. The whole job took about 30 minutes because I had trouble disconnecting the old element. I used the flat end of the scrapper to push against the connector while I pulled the element out. Normally it would take only about 15 minutes.
Read less
Was this helpful?
Thank you for voting!
The element was completely gone.
1 person
found this instruction helpful.
-
Hudson from Cockeysville, MD
- Really Easy
- Less than 15 mins
-
Screw drivers
Turned off power, removed 2 screws, un-hooked the connections, them put in the new element in reverse order.
Was this helpful?
Thank you for voting!
No Bake, only Broil
1 person
found this instruction helpful.
-
Edward from Adamstown, MD
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
POWER OFF! Unplugged oven from wall.
(Note: I found it easier to disconnect the wires from the element by removing the rear cover. Fumbling around inside the oven was getting me nowhere.)
Removed rear cover.
Disconnected old element.
Unscrewed the old element from inside the oven, removed, and installed t ... Read more he new element. Screwed the new element in place.
Reconnected wires in back, installed the back cover.
Connected power.
Tested. Good as new.
(Note: I found it easier to disconnect the wires from the element by removing the rear cover. Fumbling around inside the oven was getting me nowhere.)
Removed rear cover.
Disconnected old element.
Unscrewed the old element from inside the oven, removed, and installed t ... Read more he new element. Screwed the new element in place.
Reconnected wires in back, installed the back cover.
Connected power.
Tested. Good as new.
Read less
Was this helpful?
Thank you for voting!
replace broken bake element
1 person
found this instruction helpful.
-
Frances from MOREHEAD, KY
- Very Easy
- 15 - 30 mins
-
Screw drivers
Unplugged the range. Took our the oven shelves. Unscrewed the bars holding the broken bake element to the back of the oven wall. Gently pulled out the wiring to which the bake element is attached. Slipped the ends of the broken bake element off the ending on the wiring. Then slipped the ends of the new bake element over the ends on
... Read more
the wiring. Then pushed the wiring with attached bake element back into their position behind the oven wall and attached the bars holding the bake element to the back of the oven wall. This is really easy because it is exactly like the on-line video, for I am a 75 year old female with little technical experience.
Read less
Was this helpful?
Thank you for voting!
Element burn out. Would not heat
1 person
found this instruction helpful.
-
Dennis from AIKEN, SC
- Very Easy
- 15 - 30 mins
-
Nutdriver
Turn Circuit breaker off.Open the Oven door removed the 2 screws to the top surface. Disconnect the wire harness mark and remove the wires from the Old Element, removed the screws holding the element to top surface, Remove element replace with new element. Install wires, install screws, reconnect wire harness reposition surface. Reinstall
... Read more
screws and turn Circuit breaker power back on. Done and Done
Read less
Was this helpful?
Thank you for voting!
No problem installing the sensor
1 person
found this instruction helpful.
-
tommy from FAYETTEVILLE, NC
- Very Easy
- Less than 15 mins
-
Screw drivers
I removed the two mounting screws and pulled the harness through the opening unsnapped the sensor from the harness and installed the new sensor i didn't have to used the adapters the new sensor fitted
Was this helpful?
Thank you for voting!
The Baking Element won't heat to bake.
1 person
found this instruction helpful.
-
Kiara from JACKSONVILLE, FL
- Very Easy
- Less than 15 mins
-
Screw drivers
I had the problem before and had to call in a Tech to repair the baking element in my oven. It cost me $150.00 for the repair. This time I decided to do the repair myself, so I went online and found this site The instruction video made it very easy. I am very proud of what I was able to do without calling a Tech. My oven works like new, I
... Read more
t only cost less than $40.00 for the total repair. I am so glad this site were there when I needed them.. Thanks a Lot..
Read less
Was this helpful?
Thank you for voting!
Oven would not hold temperature, not turn on, and would shut off during use.
1 person
found this instruction helpful.
-
John from Arvada, CO
- Very Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Extremely simple repair to make. Move stove away from wall and disconnect power. Remove the oven racks. Remove the rear sheet metal panel covering the wiring harnesses. Caution: Sharp edges and corners on sheet metal.Sensor is located in upper left corner on rear oven wall. Using a long-shafted #2 Philips screwdriver, remove the two Phili
... Read more
ps head screws and gently pull the sensor 1" away from the oven wall. At this point, it will help to have an assist from someone while you are behind the range. Have the assistant gently tug on the sensor while you watch for wires moving on the rear of the range. After locating the sensor wires, gently disconnect the plastic connector clip. Note: plastic connectors become brittle with age and exposure to heat Move to front of range and gently remove sensor from rear wall by pulling the wiring through the oven wall. Before inserting the new sensor wire through the oven wall, "dry fit" the wiring connectors to see that the new sensor is a correct connection. Make connection, and secure the sensor to the rear oven wall with the two screws. Install racks, reinstall rear sheet metal panel, and connect the power. Set the oven baking temperature to a moderately low temp, 300 - 350 deg. to test the new sensor.
Read less
Was this helpful?
Thank you for voting!