3888 Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven Temperature was 50 degrees low
2 of 3 people
found this instruction helpful.
-
Eugene from Clinton, IA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Took screws out of the back on the side the sensor was on, unplugged it & took out the two screws on the inside of the oven to release the sensor. Put new sensor in place with the two screws & used one of the adapters to plug in the new sensor. Put screws back in the back panel & turned on the oven which unfortunately is still 50 degrees
... Read more
low. Need a new clock with computer which is out of stock & unavailable. I was an electrician for 25 years so didn't experience any problems. It was a cheap thing to try.
Read less
Was this helpful?
Thank you for voting!
front burner would not heat
2 of 3 people
found this instruction helpful.
-
Jack A from Biloxi, MS
- Really Easy
- Less than 15 mins
-
Socket set
simply took off smooth surface top flipped it upsde down on a towel. unbolted the entire burner assembly. matched connections with the new burner with limit switch. replaced smooth surface top plugged it in. no problems. extremely easy fix no repair charges.
Was this helpful?
Thank you for voting!
I needed a broiler pan
4 of 9 people
found this instruction helpful.
-
Rhoda P. from Secaucus, NJ
- Really Easy
- Less than 15 mins
I took the broiler pan out of the shipping container and put it in the oven.
Other Parts Used:
Was this helpful?
Thank you for voting!
Element burned out.
2 of 4 people
found this instruction helpful.
-
Raymond from Ottawa, OH
- Really Easy
- Less than 15 mins
-
Screw drivers
First I removed the two screws that hold the element in place. I then pulled the element out aobut 3 inches and disconnected the wires.
Was this helpful?
Thank you for voting!
Bake element would no longer heat up
1 person
found this instruction helpful.
-
Joe from Schertz, TX
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
I unplug the stove first. Then took off two screws that held the bake element in place. Pulled off the connectors using the pliers. Had to use pliers because they were really snug. Plug in the wires to the new base element. Crimped down the connectors a little bit to make sure they were snug. Inserted the bake element back into the
... Read more
holes at the back of the oven. Put the two screws back in. Plugged the oven back in and turned it on to make sure it worked. Lastly, tossed the old bake element in the trash. Really easy job. Glad I didn't pay anybody to do this.
Read less
Was this helpful?
Thank you for voting!
snapped element
1 person
found this instruction helpful.
-
Paul from Yukon, OK
- Easy
- Less than 15 mins
-
Screw drivers
switch off the range. undo the two screws & unplug the two tabs. Replace with new element, connect two tabs, screw back in place. done!
recieved my replacement part the next day after ordering
recieved my replacement part the next day after ordering
Was this helpful?
Thank you for voting!
Element burned out.
1 person
found this instruction helpful.
-
Wayne from Marietta, GA
- Easy
- Less than 15 mins
-
Screw drivers
Turn off breaker.
Unscrew old element, disconnect wires.
Connect wires to new element, tighten screws.
Breaker back to ON.
Done.
Unscrew old element, disconnect wires.
Connect wires to new element, tighten screws.
Breaker back to ON.
Done.
Was this helpful?
Thank you for voting!
Bake Element Melted
1 person
found this instruction helpful.
-
Bert from S. Easton, MA
- Easy
- Less than 15 mins
-
Screw drivers
Unplugged stove, unscrewed element pulled element out about 3 inces and disconnected element. Took model of stove looked on line for part. PartSelect had the best price and easiest web site to order part. Ordered part about 4pm and received part in 2 days. Took element out of box plug into connections and screwed the element back in.
... Read more
Plugged stove in and worked perfect.
Read less
Was this helpful?
Thank you for voting!
Bake element had burnt in half.
1 person
found this instruction helpful.
-
Joyce from ROCHESTER, IN
- Really Easy
- Less than 15 mins
-
Screw drivers
Watched the video that was available and followed the instructions. Unplugged the stove first,removed the old element, and put the new one in. Video was very helpful and the installation was very easy. Was done in about 10 minutes.
Was this helpful?
Thank you for voting!
element burnt into.
1 person
found this instruction helpful.
-
John from Overton, TX
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
The part came quick and packed very well. I moved the stove out and un pluged it. opened oven door and took a philips screwdriver and took the screws out at the back of element..Slid it out with the two wires attached and unpluged the conectors. pluged the conectors on to the new element and slid it back in. Had a chocolate cake in 35
... Read more
minuts.
Thanks, John in Texas
Thanks, John in Texas
Read less
Was this helpful?
Thank you for voting!
Bake Element broke
1 person
found this instruction helpful.
-
Joseph from Warwick, RI
- Really Easy
- Less than 15 mins
-
Screw drivers
****Threw the breaker switch for the oven to the 'off' position****. Opened the oven. Unscrewed the phillips head screws at the back of the old element. Removed the connecting wire, taping them to the stove so that they wouldn't recede into the hole. Securely attached the connecting wires to the new element. Pushed the wires back into th
... Read more
e holes in the stove. Removed the tape from the oven. Screwed the element into place. ****Threw the breaker switch back to the 'on' position****. Process took under 10 minutes.
DO NOT FORGET TO UNPLUG OR TURN OFF BREAKER BEFORE DOING ANYTHING WITH THE WIRES. Don't forget to turn it back on again when you are done.
DO NOT FORGET TO UNPLUG OR TURN OFF BREAKER BEFORE DOING ANYTHING WITH THE WIRES. Don't forget to turn it back on again when you are done.
Read less
Was this helpful?
Thank you for voting!
hot spot in center of bake element appeared suggesting failure was imminent
1 person
found this instruction helpful.
-
burton from prides crossing, MA
- Really Easy
- Less than 15 mins
-
Screw drivers
pulled breaker,removed oven door,removed 2 screws,pulled bake element out 3 inches,pulled connections off,pushed connectors on new element,pushed new element back and replaced screws,replaced oven door ,pushed breaker back and turned on oven and let it heat up to 350 degrees.
Total time 10 minutes,even a caveman could do it.
Total time 10 minutes,even a caveman could do it.
Was this helpful?
Thank you for voting!
BurntBaking Element Element
1 person
found this instruction helpful.
-
Matt from Lewisburg, TN
- Really Easy
- Less than 15 mins
-
Screw drivers
Turn Off the BREAKER!!!
Unplug the stove/oven
Opened the oven door
Unscrewed the baking element for the oven
Pulled the old element out about 3"
Disconnected the wire clip on both sides
Plugged the element into the clips
Screwed element back into place
Plugged oven in ,turned on breaker
PREST ... Read more O DONE
Unplug the stove/oven
Opened the oven door
Unscrewed the baking element for the oven
Pulled the old element out about 3"
Disconnected the wire clip on both sides
Plugged the element into the clips
Screwed element back into place
Plugged oven in ,turned on breaker
PREST ... Read more O DONE
Read less
Was this helpful?
Thank you for voting!
bottom bake element broken and burned
1 person
found this instruction helpful.
-
Carolyn S from white oak, NC
- Really Easy
- Less than 15 mins
-
Screw drivers
First throw the breaker on the stove. Remove two screws in back of oven then slowly pull out loosen the wire attachements ......got new part in 2 days just as simple reverse the removal directions.,,,I am over 60 female and it was simple.
Was this helpful?
Thank you for voting!
element had cracked
1 person
found this instruction helpful.
-
TONI from SALISBURY, NC
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
First I cut the power to the stove. Then I unscrewed the two screws. Pulled the element out a few inches. I had to use pliers to disconnect it from its wires. It was a very tight fit. Then I reconnected the new element. Cut the power back and and fired her up. Boy did she burn like fire.
Was this helpful?
Thank you for voting!