3888 Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
the burner element stopped working
2 of 2 people
found this instruction helpful.
-
Dominic from Fleetwood, PA
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers, Screw drivers
Unscrewed ceramic stove top , lifted top and exposed element , unscrewed element from top and disconnected wireing (marking wires to assure proper reinstillation .
Took new element and attached to top and returned wires to proper terminals , there was A slight change in wireing but was easy to understand and quick to adjust to new el ... Read more ement .
Replaced top on stove and rescrewed to secure .
Took new element and attached to top and returned wires to proper terminals , there was A slight change in wireing but was easy to understand and quick to adjust to new el ... Read more ement .
Replaced top on stove and rescrewed to secure .
Read less
Was this helpful?
Thank you for voting!
Oven would not heat
2 of 2 people
found this instruction helpful.
-
francis from mount holley, VA
- Really Easy
- Less than 15 mins
-
Screw drivers
Spoke to your very helpful staff, who advised me that a likely problem was the oven sensor. I took a chance and ordered the part, which came promptly. Your service video for the part was most helpful in my decision to try the part. Installation was a breeze, but it was the oven controller board that had failed and not the oven sensor.
... Read more
That called for a service professional, who ultimately fixed the problem. Your service though, was excellent and I would highly recommend you to others.
Read less
Was this helpful?
Thank you for voting!
left cover for the oven light broke when trying to replace the bulb
2 of 2 people
found this instruction helpful.
-
Mark from SHOREVIEW, MN
- Very Easy
- Less than 15 mins
Ordered the part. when it arrived-quite speedily, I just unpacked it and put the cotton gasket around the glass and screwed it to the proper place in the oven. Very easy.
Was this helpful?
Thank you for voting!
The element on my 20+ year old Jenn Zaire oven had broken in two...
2 of 2 people
found this instruction helpful.
-
Mary from New Britain, PA
- Very Easy
- Less than 15 mins
-
Screw drivers
Went online to find replacement part. (Because I’m cheap) Came across the website, found the part by model number, and watched the wonderful replacement video that was right on the same page as the part. After the part arrived, (in just a couple of days) I put the new one in. Only took a couple of minutes! Perfection! Thanks for making m
... Read more
y problem, no problem at all!
Read less
Was this helpful?
Thank you for voting!
Oven would over heat and produce a F2 error code on the display. It would not turn off or cool down until I switched the circuit breaker off.
2 of 2 people
found this instruction helpful.
-
richard from SAINT MARYS, KS
- Very Easy
- Less than 15 mins
-
Screw drivers
I switched the oven sensor easily enough, but it did not remedy the problem, so we are in the process of replacing the oven since it's about 20 yrs. old.
Was this helpful?
Thank you for voting!
Broken door hinges
3 of 5 people
found this instruction helpful.
-
Don from MANSFIELD, OH
- Easy
- 30 - 60 mins
-
Screw drivers
Replace hinge they didn't fit well at all.
Was this helpful?
Thank you for voting!
Cooling fan runs fault code displayed
2 of 2 people
found this instruction helpful.
-
FRANK from CLARENCE CTR, NY
- Easy
- 30 - 60 mins
-
Screw drivers
Removed the two screws holding the sensor to the rear oven wall. pulled out sensor wire. It was caught on other wires behind the oven. removed the three screws holding the 8" inspection plate in the center of the rear panel. Carefully move the insulation and reach in to grasp the back end of the sensor wire. Once free from the snag it eas
... Read more
ily pulls out with the sensor just as stated in the video. using the appropriate adaptor it was easy to re-asseble and and attach to the oven wall. Replace the rear panel with the three screws and it was done
Read less
Was this helpful?
Thank you for voting!
Maytag range had "F3" code display, oven would not work.
2 of 2 people
found this instruction helpful.
-
phillip from Farmington, NM
- Difficult
- More than 2 hours
-
Nutdriver, Screw drivers
Oven sensor replacement was easy. Thermistor was installed in less than 15 minutes. After installation STILL had "F3" error message. Harness was ok, "Clock" or ECU needed to be replaced. "Computer" is obsolete, no spares available, some companies will rebuilt for $400+. Since the stove was going to the landfill I had nothing to lose
... Read more
by taking the "Clock" apart. It has one chip that is probably the power supply and control chip, another chip is an EEPROM with 128 bytes of storage and the last is a darlington chip that controls the relays. Cleaned up everything that looked like it needed cleaning with alcohol. When I reassembled the unit the pins for the thermistor harness felt loose, so I took it apart, again, and found cold solder joints on all four pins. It must have been there all along but plugging and unplugging the harness finally broke out the solder so I could see it. Soldered the pins back in and now it all works. It's worth a try if you're getting the "F3" message. If the relays on your stove aren't working it would be a good idea to replace the darlington chip. Good luck.
Read less
Was this helpful?
Thank you for voting!
The Hinge Was Broken
4 of 8 people
found this instruction helpful.
-
Jeff from Omaha, NE
- Easy
- 30 - 60 mins
-
Screw drivers
We moved into a house with seemingly newer looking appliances. After the dishwasher broke and destroyed our floor, we found out that they were all twelve years old. Amazing the condition they were in after all that time.
The oven was the next thing to break. The hinge snapped, and while we could still use the oven, it allowed h ... Read more ot air to seep out.
So I checked online and lo and behold, I found a hinge for under $20. Wow. Much cheaper than a new range.
The most amazing thing was that I purchased it on a Friday afternoon, and it showed up on Saturday, so we could do the repair over the weekend. I cannot tell you how impressed I am with that kind of service.
We had to take off the side panel which was a pain, but all in all, it was 7-8 screws and swapping the hinge was easy. One of the screws did not want to go back in, so I had to find a replacement, but other than that, it was a pretty easy repair.
Thanks!
The oven was the next thing to break. The hinge snapped, and while we could still use the oven, it allowed h ... Read more ot air to seep out.
So I checked online and lo and behold, I found a hinge for under $20. Wow. Much cheaper than a new range.
The most amazing thing was that I purchased it on a Friday afternoon, and it showed up on Saturday, so we could do the repair over the weekend. I cannot tell you how impressed I am with that kind of service.
We had to take off the side panel which was a pain, but all in all, it was 7-8 screws and swapping the hinge was easy. One of the screws did not want to go back in, so I had to find a replacement, but other than that, it was a pretty easy repair.
Thanks!
Read less
Was this helpful?
Thank you for voting!
Broil element burst
2 of 2 people
found this instruction helpful.
-
Ronald from WEST COLUMBIA, SC
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Drop in range was in excellent condition until element burst and was getting ready to purchase another range and then I was looking to replace the element and found part select and they were great from the order process and shipping was fast and the whole process was 5 STARS. As far as me doing the repair I watched the video and it was s
... Read more
imple for even me. I also replaced the bake element at the same time. Once again I highly recommend Part Select and they are second to none.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Bake element eroded
2 of 2 people
found this instruction helpful.
-
Alison from NORTH EASTON, MA
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers, Socket set
Everything was straightforward other than the tabs that the screws go through before going into the back of the oven were the wrong size and the predrilled holes were not in the right location. Had to trim the metal tabs and redrill the screw holes.
Other Parts Used:
Was this helpful?
Thank you for voting!
broken hinge
2 of 2 people
found this instruction helpful.
-
steven from STATEN ISLAND, NY
- A Bit Difficult
- 1- 2 hours
-
Screw drivers, Wrench (Adjustable)
oven had to completely come out cause two sheet metal side panels had to be removed to get to hinge.
Was this helpful?
Thank you for voting!
The oven glass shattered when I dropped water in the heated Glass
2 of 3 people
found this instruction helpful.
-
Franziska from Salt Lake City, UT
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
I Lifted the oven door from the hinges and removed all the screws to get to the broken glass pane, since the oven door is in layers I taped the screws close to where they belonged, so that I could screw everything together again in the right order..
The last time this happened to me(!!) I brought the door to a repair man and hadto pa ... Read more y 200 dollars , I saved 150 Dollars doing it myself!
The last time this happened to me(!!) I brought the door to a repair man and hadto pa ... Read more y 200 dollars , I saved 150 Dollars doing it myself!
Read less
Was this helpful?
Thank you for voting!
Broken glass in oven door
3 of 6 people
found this instruction helpful.
-
Jamie from Hoover, AL
- Easy
- 30 - 60 mins
-
Screw drivers
Disassembled the oven door, removed broken glass, replaced with new glass and reassembled oven door. Took very little time. Online diagram on this site helped to keep everything in order and easily know what part was needed. Thanks!!!!
Was this helpful?
Thank you for voting!
No temperature control
2 of 3 people
found this instruction helpful.
-
Max from Houston, TX
- Easy
- 30 - 60 mins
-
Screw drivers
Turned off breakers to oven. Removed two screws that held oven in cabinet. Removed oven door by opening slightly and pulling up on door. Pulled oven out 1/3 of way. Took out four screws on top of control panel. Took oven light switch off by unscrewing holding ring. Removed temp knob on right by pulling. Removed start / stop knob same way.
... Read more
Removed glass straight out. Removed four screws that held elecrtonic clock conrtol board. Unpluged three wire plug from right side and the nine wire plug from the left side. Worked board out at and angle. Went backwards to connect and replace board, screws and door.Slid oven back in and tested oven after turning breakers back on, worked like new.
Read less
Was this helpful?
Thank you for voting!