EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3848 - Instructions

All Instructions for the 3848
121 - 135 of 192

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
frig door kept slamming into cabinet
  • Anthony from Riverview, FL
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
took the old stop off put the new stop on
Was this helpful?
Thank you for voting!
refig light did not work
  • paul from east hanover, NJ
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
per your instructions
Was this helpful?
Thank you for voting!
Starter/overload assembly and run capacitor were bad
  • Colby from Blanding, UT
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Removed rer cover, unplugged starter assembly from side of compressor and replaced unit with a new one. Plugged fridge in and it works good.
Was this helpful?
Thank you for voting!
refrigerator and freezer would not cool
  • Robert from Brighton, MI
  • Really Easy
  • 15 - 30 mins
Remove back cardboard, slide clip off that holds capacitor in place then unplug. plug in new parts replace clip and back cover and your done! refrigerator works great again thanks for quick shipping as well.
Was this helpful?
Thank you for voting!
Fan motor noisy
  • David from PIONEERTOWN, CA
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
Turn off refrigerator. Remove the plastic air flow cover, styrofoam channel and metal panel inside freezer compartment, remove hex nuts holding motor mount, unplug connector, remove old grommets, remove compression ring, (note 1/4 inch extension of shaft through fan) carefully pull fan blade off motor shaft and put on new motor shaft, le aving 1/4 inch of shaft extending through, replace compression ring. If your new fan motor has a female snap connector and the old motor has a male connector (as mine did) you will have to cut the wires on both new and old motors, splice and solder the male connector onto the wires of new motor, wrap carefully with premium electrical tape (or shrink tubing). Replace the 2 grommets, Reconnect the fan and bolt back into place. Make sure all the bolts around the mount are tight. Replace the metal panel. Manually spin the fan making sure it is free of the shroud. If it binds in the shroud, physically move the motor and mount till it rotates freely. Turn on refrigerator and test fan operation. If it's all good, replace the styrofoam and plastic cover.
Was this helpful?
Thank you for voting!
Unusual noise from freezer.
  • Vincent from Lyndhurst, NJ
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Replaced above parts and the noise problem was not resolved. Ordered a new motor, fan blade and another set of grommets from PartSelect. The parts were delivered the next day. Took me about 15 minutes to swap the new parts in. It's been 3 days since the repair and the noise has not returned.
Was this helpful?
Thank you for voting!
Refrigerator and freezer drawer would not maintain set temperature
  • James from Bel Air, MD
  • A Bit Difficult
  • 30 - 60 mins
  • Socket set
Condenser fan motor was running slow. This was not a problem included in your list of possible problems. I thought that maybe the capacitor was bad but have no way to check it. So I ordered one. when I received it, I installed it. That was not the problem. So I ordered a fan motor and installed it. That was not the problem. So finally I o rdered a control board and installed it. That solved the problem. So maybe you should put "cond.fan motor runs slow" in your list of possible faults and what causes that problem. Capacitor was easy to install, simply remove the cover plate, flip off retaining wire, unplug the capacitor and replace. Fan motor was a bit more difficult. It must be removed from mount after fan scroll is removed. Remove one screw that holds scroll, bend the top down and remove. Then pull hard on fan blade to remove it. It must be installed on new motor. Two screws in frame mount can be removed with some effort if you have a 1/4" drive ratchet with a Phillips screwdriver bit. Then pull frame open and install new motor. Push fan blade on new motor shaft hard. Replacing control board was easy. I used a pair of long nose pliers with 90 degree bend to get mounting pins closed to pull board off.
Was this helpful?
Thank you for voting!
install second set pan sliders
  • William from Rockville, MD
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
Because the kit did not include fasteners, had to use wood screws and superglue.
Was this helpful?
Thank you for voting!
Refrigerator section too warm
  • Ken from Chapel Hill, NC
  • Easy
  • 1- 2 hours
  • Socket set
I followed advice from other posts on this web site. The only thing additional I'd recommend is to take pictures of assemblies before you disassemble them. A neighbor gave me that useful tip. It should be noted that I first noticed my refrigerator failure back on June 22, 2012. I hired a reputable local repair service to fix it. They replaced the Defrost heater (item 618) and charged me $ 208.14. Then on August 22nd, I noticed that the problem resurfaced. I decided to fix it myself using info from site. The repair went well, and I'm hopeful that it will stay repaired. Kudos to this site!
Was this helpful?
Thank you for voting!
refrig.not cooling.freezer ok.
  • Leroy Neal from Andrews, SC
  • Really Easy
  • 30 - 60 mins
removed freezer panel,found the evap.iced up,put defrost timer into defrost. wated five min.no heat used hair dryer to defrost evap.found termination visually defective.replace defective part.no call back.Iam a EPA certified universal technician.
Was this helpful?
Thank you for voting!
a lot of ice in the freezer-and in the refrigerator is warm
  • STOYAN from ARLINGTON HEIGHTS, IL
  • Really Easy
  • 30 - 60 mins
HI I am Stoyan. I had a problem with my refrigerator. The freezer produces a lot of ice, but the refrigerator was warm. I try to find what other people comment on this site partselect.com. I decided that the thermostat is damaged. I ordered the thermostat from partselect.com and I had the delivery within 24 h. and I was very happy with t he fast delivery service .I saw a video on the same site how they show how to do myself the change of the thermostat. I took the hairdryer from my wife to defrost the refrigerator for 40 minutes and removed the old thermostat. I decided to test the heater with a 9 volts electricity from a portable charger for a car. I made an electric circuit chain and on the end of the heater I saw that there was 9 volts electricity and I understood they are ok. I changed the thermostat for 5 minutes, looking very carefully to match the colors of the cables. For $ 11, I saved money to buy a new refrigerator or pay a big bill to a repair service. Thank you for the video that helped me very much. My refrigerator work well.
Was this helpful?
Thank you for voting!
light switch quit working
  • David from Simpsonville, SC
  • Easy
  • Less than 15 mins
  • Screw drivers
removed the inside fridge electrical panel and swapped switches
Was this helpful?
Thank you for voting!
Lost Set Screw
  • Barbara from Mansfield, TX
  • Easy
  • Less than 15 mins
Took set screw and allen wrench and screwed set screw into place.
Was this helpful?
Thank you for voting!
Both the fridge aqnd freezer would not get cold.
  • Mary from Farmingdale, NY
  • Easy
  • Less than 15 mins
  • Screw drivers
Easy. Followed the video instrucations. the part was right there next to the compressor.
Was this helpful?
Thank you for voting!
failed light switch
  • Jules from Crowley, LA
  • Easy
  • Less than 15 mins
  • Pliers, Screw drivers
I started removing the switch by prying on the right side with a screwdriver, when it emerged enough I used pliers to finish removing it. I then unpluged rhe wires from the bad switch and pluged them on the new switch and "poped" it into the hole.
Was this helpful?
Thank you for voting!
All Instructions for the 3848
121 - 135 of 192