3848 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Fan stopped working, Ice maker burned out
0 of 1 people
found this instruction helpful.
-
TODD from PLAINVILLE, CT
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Screw drivers
Fan Quit So did the Ice Maker. $150.00 worth of parts plus my time. Also the Freezer Floor cracked for some stupid reason.
Other Parts Used:
Was this helpful?
Thank you for voting!
The evaporator fan in the freezer compartment began making a loud noise.
0 of 1 people
found this instruction helpful.
-
Boyd from Rapid City, SD
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
I found a replacement evaporator fan motor and 2 mounting bracket grommets at PartSelect.com at a reasonable price. I watched the installation video provided and installed the new parts as shown in the video start to finish installation time 22 minutes.i
Was this helpful?
Thank you for voting!
Light burnt out.
2 of 8 people
found this instruction helpful.
-
Roscoe G from ROCHESTER, NY
- Very Easy
- Less than 15 mins
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this helpful?
Thank you for voting!
Cracked Dairy Door
0 of 3 people
found this instruction helpful.
-
Fr Kerry from Washington, DC
- Really Easy
- Less than 15 mins
PartSelect shipped me the part and it arrived in less than 3 days. It took longer to unwrap the excellent packing than it did to pop the new door into place. Wonderful!
Was this helpful?
Thank you for voting!
Center slide missing on crisper drawer
0 of 4 people
found this instruction helpful.
-
Deanna from Glendale, AZ
- Really Easy
- Less than 15 mins
Took out the drawers slipped the new track into place and replaced the drawers.
Was this helpful?
Thank you for voting!
light in freezer section not working
6 of 24 people
found this instruction helpful.
-
Victor from Fort Myers, FL
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Using plyers Pulled old switch down and out. Put new one in and pushed new switch up into position. The switch plugs into the contacts, no wiring needed. Worked like a charm. You saved me 200 dollars GE repair bill. Thanks
Was this helpful?
Thank you for voting!
Compressor not coming on
-
Kevin from Morris, IL
- Easy
- 15 - 30 mins
-
Nutdriver
Had to e-mail GE for electrical schematic. Checked voltages to compressor. Jumpered compressor to see if it would even come on. Found bad run capacitor. Fixed.
Was this helpful?
Thank you for voting!
broking slide
-
Anthony from Painter, VA
- Easy
- 15 - 30 mins
replace the bar lift top off
Was this helpful?
Thank you for voting!
defrost timer was bad
-
Reese from Coconut Creek, FL
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
repalaced the old one with the new one. easy
Was this helpful?
Thank you for voting!
Frezzer would freeze up, refrigerator stayed cold, solved the problem. Now the refrigerator seems to be running more than usual.
-
Henry from West Seneca, NY
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Checked the defroster coil which is located behind the rear panel in the freezer compartment, it was still working. Followed the schematics down to the defrost timer, which is located in the lower front of the refrigerator and tried that. Plugged in the new part and the problem is solved.
Was this helpful?
Thank you for voting!
Added a Second Snack Pan
-
WILLIAM from CHESAPEAKE, VA
- Easy
- 15 - 30 mins
-
Nutdriver
My fridge came with only a single snack pan, and since the glass shelves are identical I decided to order the parts needed for installing the second snack pan. The glass shelf is secured in front by a round plastic pin protruding from the side of the fridge. Once the shelf is lifted upward and free of this pin, the rear retaining ears on
... Read more
the metal shelf side brackets can be released from the vertical-slotted metal track at the rear of the fridge. Make certain that you have the Right and Left snack pan slides oriented correctly, and positioned on the correct side of the metal shelf brackets. You’ll need to thread two self-tapping screws into each of the snack pan slides: one near the front, and the other at the rear. These screws extend through the metal side brackets into pre-aligned holes in each pan slide. When this is completed, you can test-fit the new clear plastic pan slide (drawer) into the slides to make sure it fits correctly. All that's left to do is insert the retaining ears into the appropriate pair of slots at the rear, then lower the front of the glass shelf until it's properly positioned over the plastic support pin. Now you're ready to enjoy twice the snack pan capacity as before!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
The refrigerator made a humming/grinding sound
-
Glenroy from Martinsburg, WV
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
I used the socket set to remove pannel that allowed me to have access to the evaporator fan. Once the fan and it's container was visible, I removed the entire fan container using the socket set. I took the fan out of the container, removed the damage blade and the damaged fan grommets. I then replace the old blade with the new blade and p
... Read more
ut the fan and the compartment back together. I am not very handy so if I am able to do this, anybody can. Ps. I was very very pleased with the services I received from PartSelect and would encourage others to use them - must admit I was very suspicious at first.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Freezer And Frig Both Warm And Compressor Would Not Run
-
joe from decatur, GA
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
I replaced the thermostat, temperature sensor, and the run capacitor. . . Refrigerator still not cooling. I checked the start relay and measured the input terminals on the compressor for the correct resistance. . . Everything measured correctly. In a last ditch effort before calling for service, I pulled the main board, inspected it and
... Read more
saw the problem right away. One leg on the compression capacitor had desoldered itself. Got out my soldering iron and applied a good amount of solder to that point. Put everything back together and turn it on. . . Problem fixed. The compressor kicked on right away and started cooling the refrigerator.
Read less
Was this helpful?
Thank you for voting!
Compressor would not run
-
A.L. from Mechanicsville, MD
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Looking at the schematic I found in the back of the unit, it appeared that there were not many parts associated with the problem. I removed the Overload/PTC and run Capacitor as a single unit. Although the capacitor was listed as the most likely problem part I decided to order both items since small particles of non-ferous material were f
... Read more
alling out of the Overload/PTS plastic case. I installed both parts as a unit and plugged the refrigerator in. The compressor did not come on so I figured that there were other problems. After about 15 minutes I returned to the unit and found it running. It is now quieter than it has ever been. I now feel that the defective part was the Overload/PTC unit and not the capacitor.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
A power surge made my side by side refrigerator stop working
-
Country at from SAYRE, OK
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
I started at the compressor and replaced the overload and the Ptcr first and that did not make the compressor start running again, so I replaced the capasitor and it still did not start, so I bit the bulett and replaced the Main Control Board and that is what I should have checked first, when I removed the old one I found a little burnt s
... Read more
pot on the back that I could not see from the front. The new one did not look exactly like the old one, it had two more wire terminals than the old one, but just leave them blank and everything will work just fine!
Read less
Was this helpful?
Thank you for voting!