3848 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Light Switch Not Working - Needed New Switch
1 person
found this instruction helpful.
-
Joe from SUGAR LAND, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
Remove the top cover above the door by lifting it slightly and pulling forward. I used a mirror to make sure that there was nothing in the way of accessing the switch from above. I used a blade screwdriver to press against the switch retainer on the topside, while GENTLY prying from below with another blade screwdriver to get the switch d
... Read more
islodged. Once the retainer was past the opening, I wiggled the switch downward and then rotated it to the left when the rounded top right edge of the switch was visible. This allowed the wiring to the connector to pass thru the hole. I pushed the wiring from the top and pulled from below to get the connector below the opening for the switch. I then unplugged the switch, plugged in the new switch and reversed the removal process feeding the connector thru first then rotating the switch to the right to get the rounded edge of the switch thru the opening, then pressed the switch up into the opening until it snapped into place. Total time less than 10 minutes.
Read less
Was this helpful?
Thank you for voting!
Light went out in refrigerator
1 person
found this instruction helpful.
-
Gary from EAST JORDAN, MI
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Pop out switch, pull wires, attach wires to new switch and pop back in. Easy smeasy!
Was this helpful?
Thank you for voting!
Was not allowing defrost heater to work
1 person
found this instruction helpful.
-
Ronnie from MARION, LA
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers, Screw drivers
Unplugged refrigerator Removed the cover in freezer compartment
Removed old thermostat and installed new
Replaced cover and plugged in refrigerator
Removed old thermostat and installed new
Replaced cover and plugged in refrigerator
Was this helpful?
Thank you for voting!
Defrost Timer went bad.
1 person
found this instruction helpful.
-
Phillip from HARRISON, MI
- Very Easy
- Less than 15 mins
-
Socket set
I sent back the other one with the print out for FedEx that your company e-mail to me and then i put the new one in, very easy took a few min's
Thank you Mr. Phillip Lewis
Thank you Mr. Phillip Lewis
Was this helpful?
Thank you for voting!
Broken light switch
1 person
found this instruction helpful.
-
Deborah from BRADLEYVILLE, MO
- Very Easy
- Less than 15 mins
-
Pliers, Screw drivers
This was so easy I think it took me 2 minutes. I am not very mechanically inclined but that didn't matter! Works perfect thank you!
Was this helpful?
Thank you for voting!
The light inside the oven had burned out
3 of 7 people
found this instruction helpful.
-
Catherine from SEATTLE, WA
- Very Easy
- Less than 15 mins
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
... Read more />3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
... Read more />3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Read less
Was this helpful?
Thank you for voting!
Loud whirling noises when the motor started up, then they subside (and stop) in a short time
1 person
found this instruction helpful.
-
Randy from VALLEY CENTER, CA
- Very Difficult
- More than 2 hours
I have not yet done the repair. After watching this repair video two problems came to mind. First I only ordered one grommet not knowing that there were two (or more I don't yet know). The second problem is that this video must be for a fridge from like the 1940, but it looks NOTHING like mine from 2008. The manual shows a bazillion parts
... Read more
and frankly I'm just a wee bit afraid to get started, and I am generally very handy, buuuttttttttt I don't know about this one
Read less
Was this helpful?
Thank you for voting!
Noisy
1 person
found this instruction helpful.
-
Brad from SPRING MILLS, PA
- Very Difficult
- More than 2 hours
I didn’t do the repair because I ordered two grommets. When they arrived, one of the packages was empty! Instead of just sending me another one, they refunded the part so I still need one. By the way, I was not refunded half the shipping either which was more than the part itself.
Was this helpful?
Thank you for voting!
noisy refrigerator
1 person
found this instruction helpful.
-
James from NEW YORK, NY
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set
I followed your video and completely dismantled the refrigerator evaporator motor, fan, brackets, and grommet, I completely cleaned the refrigerator including the cooling coils. I then ordered the evaporator motor ,fan, grommets, lid bumper, and brackets. The order would take a week to arrive. In the meantime I cleaned and reassembled al
... Read more
l the old parts, waiting for the new ones to come. Guess what! The refrigerator was quiet as a mouse. I really did not need the new parts, but I kept them anyway just for good luck. Not bad for a refrigerator that's twenty four years old.
Read less
Was this helpful?
Thank you for voting!
Light was flicking
1 of 2 people
found this instruction helpful.
-
Stephanie from KEARNY, NJ
- Really Easy
- Less than 15 mins
-
Screw drivers
It was way to ez to install only a couple of minutes that's it
Was this helpful?
Thank you for voting!
Broken light switch
1 of 2 people
found this instruction helpful.
-
Ted from SANDWICH, IL
- Easy
- 15 - 30 mins
-
Screw drivers
took a little more effort than the video show to remove old module and replace new. Works fine now.
Was this helpful?
Thank you for voting!
The control board generated clicking noise. Temperature display wrong values.
1 of 2 people
found this instruction helpful.
-
QUOC-LOC from LYNN HAVEN, FL
- Really Easy
- 30 - 60 mins
-
Screw drivers
On the internet forum I read that if the control board needs to be changed , do the same for the Run Capacitor/relay.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
P ... Read more lugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
P ... Read more lugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.
Read less
Was this helpful?
Thank you for voting!
Change bulb
3 of 8 people
found this instruction helpful.
-
Louis from LEAGUE CITY, TX
- Really Easy
- 30 - 60 mins
-
Nutdriver
Easy
Was this helpful?
Thank you for voting!
The door activated light switch was missing.
1 of 3 people
found this instruction helpful.
-
Don from Eugene, OR
- Really Easy
- Less than 15 mins
Pulled the two wires out from the access hole in the lower part of the refrigerator. Put them in the spade connectors on the new switch, and pushed the switch into place.
Was this helpful?
Thank you for voting!
Bad switch for door prevented interior light from coming on
0 of 1 people
found this instruction helpful.
-
Patricia from Sylva, NC
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers
Just as your video described, although due to the age of the fridge, it took a bit longer to remove the defective switch. Your video made this so simple, I can't imagine why we lived with a dark fridge for so long! I was ready to buy a whole new fridge, as repairmen are often nonexistent for small repairs. I am the biggest fan of yo
... Read more
ur company & it's repair video. THANK YOU SO MUCH
Read less
Was this helpful?
Thank you for voting!