EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3845 - Instructions

All Instructions for the 3845
106 - 120 of 360

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
NOISE FROM THE FREEZER SECTION OF THE REFRIGERATOR
3 of 3 people found this instruction helpful.
  • Sarafina from DEWEY, AZ
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
1) TURNED POWER OFF FROM REFRIGERATOR 2) REMOVED THE FREEZER SHELF FIRST BY GENTLY TAPPING THE LEFT SIDE UP AND OUT THEN THE RIGHT SIDE UP AND OUT 3) REMOVED THE 2 PHILLIPS SCREWS HOLDING THE EVAPORATIVE FAN COVER IN PLACE 4) GENTLY PUSHED THE COVER UP AND MAKING SURE THE 2 CLIPS WERE NOT DAMAGED 5) VERY GENTLY PUSHED UP ON THE STYRO FOA M SHIELD GRASPING IT FROM THE BOTTOM, BE VERY CAREFUL NOT TO CRACK OR DAMAGE THIS 6) THEN REMOVED 4 OF THE PHILLIPS SCREWS HOLDING THE BACK PANEL 7) THEN REMOVED THE 2 SCREWS HOLDING THE FAN MOTOR IN POSITION ON THE BACK COVER AND LAID THAT ASIDE 8) I COULD THEN SEE THE MOTOR SO I UNCLIPPED THE RED/DARK WIRE CLIP FROM THE HARNESS WITH MY FINGERS, THEN TOOK MY NEEDLE NOSE PLIERS AND GENTLY PULLED UP ON THE GREEN GROUND WIRE 9) I THEN REMOVED THE 2 PHILLIPS HEAD SCREWS HOLDING THE MOTOR BRACKET TO THE WALL OF THE FREEZER 10) THEN REMOVED THE ENTIRE MOTOR AND PUT THAT ON THE KITCHEN TABLE 11) TOOK MY NEEDLE NOSE PLIERS AND VERY, VERY GENTLY PRIED OFF THAT LITTLE METAL RING HOLDING THE FAN BLADE ON (TRICKY SO LEFT UP GENTLY)...I BOUGHT ADDITIONAL IN CASE I DAMAGED IT 12) TOOK MY 5/16 NUT DRIVER AND UNSCREWED THE TOP METAL BRACKET HOLDING THE MOTOR 13) LIFTED THE MOTOR OFF AND LOOKED AT THE TOP AND BOTTOM GROMMETS TO SEE IF DAMAGED OR CRACKED (I BOUGHT ADDITIONAL GROMMETS IN CASE THEY WERE CRACKED OR DAMAGED, EASY FIX) 14) THEN ATTACHED THE NEW MOTOR AND BASICALLY SIMPLY DID EVERYTHING IN REVERSE TO INSTALL THE NEW MOTOR. MAKE SURE YOU KEEP YOUR SCREWS IN ORDER SO YOU CAN IDENTIFY WHICH PART THEY CAME FROM. MAKE SURE YOU DO NOT PINCH AND WIRES WHEN RE-INSTALLING THE MOTOR. SAVED ME A REPAIR PERSON CALL.
Was this helpful?
Thank you for voting!
Fan not working
3 of 3 people found this instruction helpful.
  • joan from STERLING HTS, MI
  • Easy
  • 1- 2 hours
  • Screw drivers, Socket set
Took out old put new in. Watched a u tube, no problems
Was this helpful?
Thank you for voting!
broken Vegetable drawer frame
3 of 3 people found this instruction helpful.
  • Helen from PASO ROBLES, CA
  • Really Easy
  • 30 - 60 mins
Ordered the frame and put it in.
Was this helpful?
Thank you for voting!
Plastic bracket broke so vegetable drawer would no longer stay in place
3 of 3 people found this instruction helpful.
  • jim from CORNING, NY
  • Really Easy
  • 30 - 60 mins
Pipes out the glass from existing shelf while in place inside refrigerator. Remove broken shelf. Install new shelf. Clean and replace glass. Easy job thanks to finding the correct part from Part Select!
Was this helpful?
Thank you for voting!
freezer compartment worked fine but very little cooling going to refrigerator section.
3 of 3 people found this instruction helpful.
  • Lee from OZARK, AR
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Freezer worked great but no cooling to refrigerator section. Replaced with part ordered. Phillips head screw driver is all that is needed. Very easy to replace, it's plug and play. New part powered up neither the freezer nor the refrigerator. Went back to old part and atleast freezer still works. New part was no good from factory. The re placement part# matched the original. I attempted to contact PartsSelect but there was no response back.
Was this helpful?
Thank you for voting!
Broken Vegetable Drawer Shelf Frame
3 of 3 people found this instruction helpful.
  • Laura from CRAIGVILLE, IN
  • Really Easy
  • 30 - 60 mins
I took the broken piece out and replace it with the new replacement shelf
Was this helpful?
Thank you for voting!
Compressor would randomly not turn on. Fridge too warm sometimes.
3 of 4 people found this instruction helpful.
  • Mackenzie from Williston, ND
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Replace temperature control. That fixed it. Also, removed plastic bag obstructing air vent in freezer which added performance. Fridge works good now.
Was this helpful?
Thank you for voting!
switchlight on my refrigerator was not working
5 of 10 people found this instruction helpful.
  • Eileen from Coto de Caza, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers
I found instructions on the web about how to do this repair, so I ordered the part with confidence. But the instructions simply said "pull out the old switchlight". That was actually somewhat difficult as the clip on the side intended to hold the part in was stubborn. I eventually used a utility to slice off the clip. From that point, it was just a matter of plugging in the new switchlight , which was very simple.
Was this helpful?
Thank you for voting!
Freezer was not freezing food.
3 of 4 people found this instruction helpful.
  • Steve from Ridgecrest, CA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Inspected freezer because food was not freezing, getting cold, but not freezing. Noticed fan was not blowing air, but making a little motor noise, like it's trying to turn. Removed cover panel, and found the fan blade rubbing on the panel, fan shaft was worn out and very loose, wobley. That told me the fan needed to be replaced. Found par t on the GE Partselect website and ordered the parts via the website order process. This was easy. The parts were shipped quickley and were at my front door the next day. Couldn't believe it. The actual process was very easy: Remove cover, remove bracket holding fan motor, remove and replace motor, re-assemble parts. About 20-25 minutes from start to finish. Freezer is working like it's suppose to.
Was this helpful?
Thank you for voting!
was not defrosting
3 of 4 people found this instruction helpful.
  • denis from freedom, NH
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
first i removed all the screws inside the freezer compartment took out theback and bottom to get to the evap motor,unpluged the wires and removed the evap motor ,removed the fan from old unit and put it on the new unit them mounted it to the back wall of the fridge,,, and put back top and bottom
Was this helpful?
Thank you for voting!
Could not adjust temperature
3 of 4 people found this instruction helpful.
  • Boyd from Blaine, WA
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Replaced temp controller
Was this helpful?
Thank you for voting!
During Hurricane Ike, frig. saw several inched of saltwater and sand underneath. AFter cleaning up, I tried to run and only the blower fan worked. It must have been just above the water. The compressor did not kick on. I looked at the lowest elec. connections and saw corrsion on the overload protect
3 of 4 people found this instruction helpful.
  • ken from fulshear, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers
This was after sitting idle for 9 mos. I simply pulled the part, ordered the same part and installed. Nothing more than a couple of screws and 2 wire connections. It now works great.
Was this helpful?
Thank you for voting!
end cap to bar of freezer door broke
3 of 4 people found this instruction helpful.
  • Kimberly A from Columbus, OH
  • Really Easy
  • Less than 15 mins
Snapped end cap onto bar and installed bar onto freezer door.

I considered going to an appliance parts store but found the part very easily on the internet and had it within 2 days. I am very busy which was very helpful.
Was this helpful?
Thank you for voting!
Fridge never cuts off.freeze everything inside of fridge.
3 of 4 people found this instruction helpful.
  • Henry from DOUGLASVILLE, GA
  • Very Easy
  • Less than 15 mins
  • Screw drivers
To remove the temp sensor.2 Phillip head screws not remove the cover inside fridge .the temp control knob cover.removed that and unplugged switch.installed new switch.reinstalled cover.
Was this helpful?
Thank you for voting!
Condensor fan blade cracked, blade was sheared off.
3 of 4 people found this instruction helpful.
  • Bradley from Cedarburg, WI
  • Easy
  • Less than 15 mins
  • Pliers, Screw drivers
First, remove the cardboard cover on the back, lower portion of the refrigerator.

Next, locate the condensor fan motor assembly and blade. (Right side as you are facing)

Using a pliers, hold the shaft to keep it from turning and prevent damage to the motor. Using a screwdriver, slide the old ring compression on the b lade shaft toward the motor (away from the fan blades) to loosen.

Remove old blade from the shaft by firmly grasping the motor shaft with a pliers (to prevent from damaging) and pull the blade assembly off.

Reverse the above steps to attach the new blade.
Was this helpful?
Thank you for voting!
All Instructions for the 3845
106 - 120 of 360