3842 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Lower burner not heating:
1 person
found this instruction helpful.
-
John from Fishers, IN
- Easy
- 15 - 30 mins
-
Screw drivers
Ordered element and recieved in two days(yea). Removed back cover from unit. Removed two wire slide on wire clips. Then went inside oven cavity and removed two screws holding element intact. The element slid out. Installed element, re-installed two screws to hold element intact. Attached wire clips back on to element, re-attached back
... Read more
cover. Plugged unit back in and it worked perfectly. Eazy-peezy lemon squeezy.
John
Johnny on the Spot Home Repairs
Fishers, Indiana 317-997-3600
John
Johnny on the Spot Home Repairs
Fishers, Indiana 317-997-3600
Read less
Was this helpful?
Thank you for voting!
Inner most oven door was broken.
1 person
found this instruction helpful.
-
William from WASHINGTON, DC
- A Bit Difficult
- 1- 2 hours
-
Screw drivers
I followed peoples instructions here, and it was not very difficult.
Was this helpful?
Thank you for voting!
Replaced upper over light and assembly
1 person
found this instruction helpful.
-
Thomas from SAN DIEGO, CA
- Very Difficult
- More than 2 hours
-
Pliers, Screw drivers
I had to pull out the oven and balance the oven on two patio tables. Remove the back of the oven. Pull out the light assembly which was burnt. I was unable to remove the casing around the light, so I destroyed it with a pliers. Reinstalling the new light and assembly was easy. What made this job difficult, I could not remove the light ass
... Read more
embly from the front of the oven and had to go in from the back.
Read less
Was this helpful?
Thank you for voting!
40+ year old oven. . . worn out, obsolete door hinges. . .
1 person
found this instruction helpful.
-
Darrin from SEDRO WOOLLEY, WA
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Removed old hinges, fabricated new mounting plates from 16ga steel plate. . . Cut new hinges to fit in available space. . . Drilled and tapped new mounting holes and adjustment tracks. . . Shortened existing springs to fit new configuration. Installed new hinges.
Was this helpful?
Thank you for voting!
Oven door hinges broken
4 of 10 people
found this instruction helpful.
-
Brian from Lakewood, CO
- A Bit Difficult
- More than 2 hours
-
Pliers, Screw drivers
With the back removed, replacing the lamp receptacle is straight-forward. Likewise, the door gasket is very easy. However, in order to replace the hinges, you have to remove the burner glass top (screws underneath the front lip), and inner and outer side panels. Also the supplied hinges mounting holes were not threaded so I had to use my
... Read more
own bolts, lock-washers and nuts in order to attach them. Total time, including a bit of cleaning, was 5 hours.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
element had cracked
1 person
found this instruction helpful.
-
TONI from SALISBURY, NC
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
First I cut the power to the stove. Then I unscrewed the two screws. Pulled the element out a few inches. I had to use pliers to disconnect it from its wires. It was a very tight fit. Then I reconnected the new element. Cut the power back and and fired her up. Boy did she burn like fire.
Was this helpful?
Thank you for voting!
Previous element burnt up
1 person
found this instruction helpful.
-
Betsy from Sun City, AZ
- Really Easy
- Less than 15 mins
-
Screw drivers
I let my husband to the work...But it was very easy. I could have done it! He removed the screws, pulled the wires off previous element. Reattached the wires to the new element and screwed the ends back in place.
Was this helpful?
Thank you for voting!
Bake Element shorted out
1 person
found this instruction helpful.
-
Laurie from Clarence, NY
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
I first shut off the breaker to the stove - safety first!
I used a phillips screw driver to remove the two screws that held the old element in. Then I pulled the old element out and used the pliers to remove the electrical connections. I put the new element in, made the electrical connections and secured it with the screws. ... Read more After restoring powere via the breaker, we tested the stove and it worked. Just call me the Maytag Man!
I used a phillips screw driver to remove the two screws that held the old element in. Then I pulled the old element out and used the pliers to remove the electrical connections. I put the new element in, made the electrical connections and secured it with the screws. ... Read more After restoring powere via the breaker, we tested the stove and it worked. Just call me the Maytag Man!
Read less
Was this helpful?
Thank you for voting!
fireworks in the oven. Burned completely in two.
1 person
found this instruction helpful.
-
Shelly from Allentown, PA
- Really Easy
- Less than 15 mins
-
Screw drivers
My husband has moved out of state for his job. I am left here with the children until the house sells. This is the first time I have ever had to do any oven repair. I had excellent and fast service - my part came right away. I took out the 2 screws holding the element in place, pulled the element out, disconnected the old element, connect
... Read more
ed the new one, pushed it back in, and replaced the screws. No problem at all. I was a little nervous turning it all back on, but it is working perfectly!
Read less
Was this helpful?
Thank you for voting!
The element was completely gone.
1 person
found this instruction helpful.
-
Hudson from Cockeysville, MD
- Really Easy
- Less than 15 mins
-
Screw drivers
Turned off power, removed 2 screws, un-hooked the connections, them put in the new element in reverse order.
Was this helpful?
Thank you for voting!
burner would not heat.
1 person
found this instruction helpful.
-
Jackie from Hughes Springs, TX
- Really Easy
- Less than 15 mins
I unpluged the old burner and pluged the new one in. Repair done in about 2 min,
Was this helpful?
Thank you for voting!
element burnt into.
1 person
found this instruction helpful.
-
John from Overton, TX
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
The part came quick and packed very well. I moved the stove out and un pluged it. opened oven door and took a philips screwdriver and took the screws out at the back of element..Slid it out with the two wires attached and unpluged the conectors. pluged the conectors on to the new element and slid it back in. Had a chocolate cake in 35
... Read more
minuts.
Thanks, John in Texas
Thanks, John in Texas
Read less
Was this helpful?
Thank you for voting!
Bake Element broke
1 person
found this instruction helpful.
-
Joseph from Warwick, RI
- Really Easy
- Less than 15 mins
-
Screw drivers
****Threw the breaker switch for the oven to the 'off' position****. Opened the oven. Unscrewed the phillips head screws at the back of the old element. Removed the connecting wire, taping them to the stove so that they wouldn't recede into the hole. Securely attached the connecting wires to the new element. Pushed the wires back into th
... Read more
e holes in the stove. Removed the tape from the oven. Screwed the element into place. ****Threw the breaker switch back to the 'on' position****. Process took under 10 minutes.
DO NOT FORGET TO UNPLUG OR TURN OFF BREAKER BEFORE DOING ANYTHING WITH THE WIRES. Don't forget to turn it back on again when you are done.
DO NOT FORGET TO UNPLUG OR TURN OFF BREAKER BEFORE DOING ANYTHING WITH THE WIRES. Don't forget to turn it back on again when you are done.
Read less
Was this helpful?
Thank you for voting!
Our original surface element caught fire!
1 person
found this instruction helpful.
-
Paulo from Cambridge Springs, PA
- Really Easy
- Less than 15 mins
Old surface element was removed simply by pulling it out of the electrical contacts. The, the new one was inserted.
Was this helpful?
Thank you for voting!
hot spot in center of bake element appeared suggesting failure was imminent
1 person
found this instruction helpful.
-
burton from prides crossing, MA
- Really Easy
- Less than 15 mins
-
Screw drivers
pulled breaker,removed oven door,removed 2 screws,pulled bake element out 3 inches,pulled connections off,pushed connectors on new element,pushed new element back and replaced screws,replaced oven door ,pushed breaker back and turned on oven and let it heat up to 350 degrees.
Total time 10 minutes,even a caveman could do it.
Total time 10 minutes,even a caveman could do it.
Was this helpful?
Thank you for voting!