EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3842 - Instructions

All Instructions for the 3842
76 - 90 of 465

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
The inside glass was broken on oven door.
3 of 4 people found this instruction helpful.
  • Jacob from Cotton, MN
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
I was pleased with how the job went.
It took longer than expected because I am not really a "do it yourselfer", but I studied the door and reread how others managed the repair several times.
There were more screws than mentioned here.
Someone said 10 screws but there were 12.
In the end I was pleased and surprised how simple the job was, but recommend others read carefully what others have written. I didn't but learned one must.
Was this helpful?
Thank you for voting!
one electric burner does not get hot
5 of 10 people found this instruction helpful.
  • dinh from austin, TX
  • Easy
  • 15 - 30 mins
  • Screw drivers
swap a known good coil around and still did not work. then measured voltage across the switch terminals and found out one leg was opened. Ordered a new switch which looked alike. The new switch could handle more current than the old one. Turned out that all terminals of the new switch were same size while the old one had 1 smaller size. U sed the dremer tool to file it to fit the wire terminal. Also the burner knob had different grove type . Just forced it in.
Was this helpful?
Thank you for voting!
Burner wouldn't heat (wiring failure)
3 of 4 people found this instruction helpful.
  • Eugene from San Antonio, TX
  • A Bit Difficult
  • 15 - 30 mins
  • Pliers, Screw drivers, Wrench set
1. Shut the breaker off; Jenn-Air's design will have you working around hot leads if you don't.
2. Raise the control panel
3. Remove burner and unscrew the burner connector; trace the wires back to the control panel bottom and remove them
4. On the replacement connector, add the electrical for the control panel. These are not included and can be found at any hardware store; they are a standard size.
5. Connect the new wires and put everything back together.
6. Reset the break and test.
Was this helpful?
Thank you for voting!
Bake Element wouldn't heat up to temperature
2 of 2 people found this instruction helpful.
  • John from Foxboro, MA
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers
I had viewed the video link on PartsSelect. I removed 2 screws and proceeded to pull element out to disconnect wire connectors. However one side the wire connected was melted on to the contact tab of the element and the wire was broken off. I proceeded to remove back panel from stove and located the exposed broken wire. I stripped back wi re and installed a new wire connector that I had in my tool box. I fed wire through small hole. Then I re-installed back panel. I then connected wires to the new bake element and installed element mounting screws.
Was this helpful?
Thank you for voting!
Burner control knob/switch shaft had broken off.
4 of 8 people found this instruction helpful.
  • Steve from San Luis Obispo, CA
  • Easy
  • 15 - 30 mins
  • Screw drivers
Removed front panel of range, removed switch (2 screws), unclipped wires from back of existing switch. Installed new switch - reverse order of above.
Was this helpful?
Thank you for voting!
Bake element caught on fire
2 of 2 people found this instruction helpful.
  • Dan from TomRriver, NJ
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
I got the run around about my HARWICK stove at several part stores. Like they all said the same thing (cant look it up just bring it down) So i did and then they would say, what's the model number. ERR! SO my wife found parts select on the web and they beat the three price quotes I got. First turn the power off to the stove!!! The repair was simple. Just remove the two screws on both side's and pull the element out but just enough for the wire's to show. Disconnect the two wire's and pull the element out. Reverse the processes but when wire's are reconnected squeeze terminals end gently to ensure a good connection. This is a great company to deal with, I will be using them again. Thanks and good luck!!!
Was this helpful?
Thank you for voting!
replaced old drip pans
3 of 5 people found this instruction helpful.
  • Frances from Summerfield, FL
  • Really Easy
  • Less than 15 mins
Fastest, easiest thing I have ever done! I got my orders so fast it was unreal! Hurrah for good old American know-how. I will always recommend these good people!
Was this helpful?
Thank you for voting!
Replacing the bulb in the freezer side
5 of 11 people found this instruction helpful.
  • Yafa (and David) from Bothell, WA
  • Easy
  • Less than 15 mins
  • Nutdriver
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this helpful?
Thank you for voting!
Baking element burned out
2 of 2 people found this instruction helpful.
  • Stephen from Pleasant Hill, IA
  • Easy
  • Less than 15 mins
  • Screw drivers
I watched the video on the web site and it worked like a dream. Two screws to take out - disconnect wires put back connecting wires and replace the screws again. Just like the video. Thanks
Was this helpful?
Thank you for voting!
Drip pans were not original to range, I could not get them clean.
2 of 2 people found this instruction helpful.
  • Lynn from BRADENTON, FL
  • Really Easy
  • Less than 15 mins
I reoved old drip pans and installed new ones. Very easy, they look great!
Was this helpful?
Thank you for voting!
oven light glass cover was broken
2 of 2 people found this instruction helpful.
  • wayne from LIMINGTON, ME
  • Really Easy
  • 15 - 30 mins
took out the old dome cover and replaced it with a new one by unscrewing and replaced the new one and a fiberglass gasket. simple.
Was this helpful?
Thank you for voting!
The element on my 20+ year old Jenn Zaire oven had broken in two...
2 of 2 people found this instruction helpful.
  • Mary from New Britain, PA
  • Very Easy
  • Less than 15 mins
  • Screw drivers
Went online to find replacement part. (Because I’m cheap) Came across the website, found the part by model number, and watched the wonderful replacement video that was right on the same page as the part. After the part arrived, (in just a couple of days) I put the new one in. Only took a couple of minutes! Perfection! Thanks for making m y problem, no problem at all!
Was this helpful?
Thank you for voting!
left cover for the oven light broke when trying to replace the bulb
2 of 2 people found this instruction helpful.
  • Mark from SHOREVIEW, MN
  • Very Easy
  • Less than 15 mins
Ordered the part. when it arrived-quite speedily, I just unpacked it and put the cotton gasket around the glass and screwed it to the proper place in the oven. Very easy.
Was this helpful?
Thank you for voting!
Used part
2 of 3 people found this instruction helpful.
  • Sabrina from FREMONT, CA
  • Very Easy
  • Less than 15 mins
Lift burners out of plug discard old drip pans replace new drip pans into plugs and done .
Was this helpful?
Thank you for voting!
I needed a broiler pan
4 of 9 people found this instruction helpful.
  • Rhoda P. from Secaucus, NJ
  • Really Easy
  • Less than 15 mins
I took the broiler pan out of the shipping container and put it in the oven.
Was this helpful?
Thank you for voting!
All Instructions for the 3842
76 - 90 of 465