3842 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
needed new drip pans
7 of 10 people
found this instruction helpful.
-
Janice from Kerrville, TX
- Really Easy
- Less than 15 mins
New ones fit perfectly, and looks beautiful!
Was this helpful?
Thank you for voting!
Faulty bulb receptacle
10 of 20 people
found this instruction helpful.
-
Kenneth from Lynchburg, VA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Unplugged the stove and removed the back panel, disconnected the wires from the old receptacle, removed it, inserted the new receptacle, connected the wires, put the back panel of the stove on, plugged in the stove and then checked to see if the bulb was now burning. Success!
Was this helpful?
Thank you for voting!
The bake element broke at the rear causing a minor electric flash inside the oven
5 of 5 people
found this instruction helpful.
-
richard from Inwood, NY
- Easy
- 15 - 30 mins
-
Screw drivers
You guys had a installation video which help greatly. I did run into a couple issues. Firstly, it didn't see a plug for the oven so I shut the power down from the panel. Lastly, disconnecting the old bake element from the electric insert at the ends was a bit challenging. The element and the inserts looks as if it was one piece but event
... Read more
ually it pulled apart. Installing the new piece was very easy. You want to consider adding additional legs under the bake element closet the area where the element connect to the oven inserts. When my old element broke and failed, the live piece can in contact with the floor of the oven causing a flash. It was a bit scary.
Thank you very much for your expeditious shipment and your follow up. Great job!
Thank you very much for your expeditious shipment and your follow up. Great job!
Read less
Was this helpful?
Thank you for voting!
light bulb in water ice freezer door went bad
8 of 14 people
found this instruction helpful.
-
Carl from RIVERSIDE, CA
- Very Difficult
- More than 2 hours
-
Screw drivers
I didn't. Don't know how to get to light bulb to change it for this specific model
Was this helpful?
Thank you for voting!
6" surface heating coil remained warm when "off"
8 of 15 people
found this instruction helpful.
-
William C. from Sealy, TX
- Easy
- 30 - 60 mins
-
Screw drivers
Removed the large lower back panel of range (6-8 phillips screws) which holds upper control back panel in place. Removed upper control back panel (2 screws), exposing infinite switch electrical connections. At front face of control panel, removed (pulled off) control knob, exposing 2 phillips screws holding switch in place. (NOTE: A sl
... Read more
eeve is on the switch arm or maybe remains inside the control knob). Look for this sleeve. Without it, the knob will NOT seize the switch rotary arm.
Removed each wire connection individually, one at a time, installing it in the proper position on the new switch.
Reverse all procedures to put things back together. A very simple, straight-forward operation.
Removed each wire connection individually, one at a time, installing it in the proper position on the new switch.
Reverse all procedures to put things back together. A very simple, straight-forward operation.
Read less
Was this helpful?
Thank you for voting!
electric burner burned out
6 of 9 people
found this instruction helpful.
-
Paul from Foley, AL
- Really Easy
- Less than 15 mins
This is the second time PartSelect came through for me. If it hadn't been for you guys, I'd have had to buy a new Jenn-Air cooktop, because ours is nearly 30 years old. About two years ago, I bought a new two-burner cartridge, which installed without tools in about one minute. But a few weeks ago, we lost the burner in the other cartri
... Read more
dge. I emailed PartSelect, and even though I gave them my obsolete model number, a helpful service rep managed to find me the part number of the correct burner, so I was able to place my order. Once the part arrived, there was no problem replacing the burner. This is a simple operation we've performed many times when we need to remove the burner for cleaning.
Read less
Was this helpful?
Thank you for voting!
Store-bought drip bowls wouldn't fit.
5 of 6 people
found this instruction helpful.
-
Sharon from Yacolt, WA
- Really Easy
- Less than 15 mins
My elements just plug in so all I had to do was pull them out and replace the drip bowls. They fit perfectly!
Other Parts Used:
Was this helpful?
Thank you for voting!
Bake Element Failed
5 of 6 people
found this instruction helpful.
-
Douglas from Plymouth, WI
- Really Easy
- Less than 15 mins
-
Screw drivers
Unplugged the stove. I removed the old element by removing the two screws holding it in, and plugged the stove back in. I ordered the part and it came in 2 days. Unpluged the stove again, connected the new element, and re-attached it via the two screws. Plugged it back in, and it worked great. Fantastic price and quick delivery. Only too
... Read more
k about 5 minutes to fix, and I saved at least $100 by not having to call a service man.
Read less
Was this helpful?
Thank you for voting!
The heating element socket had crumbled with age.
4 of 4 people
found this instruction helpful.
-
Edward from Webster, NY
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Changing the socket with a new one simply required removing one screw and splicing the two existing wires to the pigtails on the new socket. It took longer to unpack the replacement part than actually doing the job.
Was this helpful?
Thank you for voting!
burner fell apart
5 of 7 people
found this instruction helpful.
-
Barbara a from Huntington, NY
- Really Easy
- Less than 15 mins
Plugged in the new burner, which we received in one day.We were delighted with the quick service
Was this helpful?
Thank you for voting!
power light on, but burner not getting hot
7 of 13 people
found this instruction helpful.
-
Aaron from Weymouth, MA
- Really Easy
- Less than 15 mins
-
Screw drivers
It was really easy. It took about 5 minutes to remove the screws holding the back in place. Another couple of minutes to remove the switch, and a few more minutes to change the wires over one at a time. Then 5 more minutes to put it all back together again, and plug it back in, and it just worked. Really simple.
Was this helpful?
Thank you for voting!
Grandson lost the ignition key to my Toro!
15 of 38 people
found this instruction helpful.
-
Michelle from AYLETT, VA
- Really Easy
- Less than 15 mins
No repair, lol! Just a perfect fit for my ignition :). I bought two in case my grandson gets curious again.
Was this helpful?
Thank you for voting!
Door gasket was hard and brittle from baked-on grease - heat leaking around door
4 of 5 people
found this instruction helpful.
-
Harlen from Spring Creek, NV
- Really Easy
- Less than 15 mins
Waited for my husband to do it, but when he didn't, I tried it. Very simple! Just pulled the old gasket out of the pinch pin holes in the door, then replaced it. Tuck the one end into the hole at the bottom of the door, then match up the little pinch pins on the gasket with the holes in the door - matches up perfectly! Be sure to tuck in
... Read more
each of pinch pins till they sort of "snap" into each hole. Took me 5 minutes, tops. Works great now, no more lost heat around the edge of the door.
Read less
Was this helpful?
Thank you for voting!
Broken levelling leg
5 of 8 people
found this instruction helpful.
-
Linda from Oneida, NY
- Really Easy
- Less than 15 mins
Took the old levelling leg out and screw the new one in.
Was this helpful?
Thank you for voting!
The drip bowls were all caked and corroded.
4 of 5 people
found this instruction helpful.
-
Terry from Mountain City, TN
- Really Easy
- Less than 15 mins
This wasn't a "repair", but I got an email asking for my story, so here it is. :-)
I followed the owner's manual instructions by pulling out the burner elements, lifting up the old drip bowls, setting in the new ones, replacing the elements.
I followed the owner's manual instructions by pulling out the burner elements, lifting up the old drip bowls, setting in the new ones, replacing the elements.
Other Parts Used:
Was this helpful?
Thank you for voting!