EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3842 - Instructions

All Instructions for the 3842
121 - 135 of 465

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
BurntBaking Element Element
1 person found this instruction helpful.
  • Matt from Lewisburg, TN
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Turn Off the BREAKER!!!
Unplug the stove/oven
Opened the oven door
Unscrewed the baking element for the oven
Pulled the old element out about 3"
Disconnected the wire clip on both sides
Plugged the element into the clips
Screwed element back into place
Plugged oven in ,turned on breaker
PREST O DONE
Was this helpful?
Thank you for voting!
bakeing element caught fire.
1 person found this instruction helpful.
  • Leticia from Sunnyvale, CA
  • Really Easy
  • Less than 15 mins
First I turned off power to the range at the fuse box (very important-The last time I didn't do this and ended up paying a repairman $150.00 to replace the damaged connectors). I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I then connected the new ele ment, pushed the element back in and replaced the screws. Turned the power back on and tested the element. The whole job took about 30 minutes because I had trouble disconnecting the old element. I used the flat end of the scrapper to push against the connector while I pulled the element out. Normally it would take only about 15 minutes.
Was this helpful?
Thank you for voting!
snapped element
1 person found this instruction helpful.
  • Paul from Yukon, OK
  • Easy
  • Less than 15 mins
  • Screw drivers
switch off the range. undo the two screws & unplug the two tabs. Replace with new element, connect two tabs, screw back in place. done!
recieved my replacement part the next day after ordering
Was this helpful?
Thank you for voting!
Element burned out.
1 person found this instruction helpful.
  • Wayne from Marietta, GA
  • Easy
  • Less than 15 mins
  • Screw drivers
Turn off breaker.
Unscrew old element, disconnect wires.
Connect wires to new element, tighten screws.
Breaker back to ON.
Done.
Was this helpful?
Thank you for voting!
Bake Element Melted
1 person found this instruction helpful.
  • Bert from S. Easton, MA
  • Easy
  • Less than 15 mins
  • Screw drivers
Unplugged stove, unscrewed element pulled element out about 3 inces and disconnected element. Took model of stove looked on line for part. PartSelect had the best price and easiest web site to order part. Ordered part about 4pm and received part in 2 days. Took element out of box plug into connections and screwed the element back in. Plugged stove in and worked perfect.
Was this helpful?
Thank you for voting!
Bake element would no longer heat up
1 person found this instruction helpful.
  • Joe from Schertz, TX
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
I unplug the stove first. Then took off two screws that held the bake element in place. Pulled off the connectors using the pliers. Had to use pliers because they were really snug. Plug in the wires to the new base element. Crimped down the connectors a little bit to make sure they were snug. Inserted the bake element back into the holes at the back of the oven. Put the two screws back in. Plugged the oven back in and turned it on to make sure it worked. Lastly, tossed the old bake element in the trash. Really easy job. Glad I didn't pay anybody to do this.
Was this helpful?
Thank you for voting!
surface element needed to be replaced along with all the drip Bowls
2 of 4 people found this instruction helpful.
  • Tawnia from SHOW LOW, AZ
  • Really Easy
  • Less than 15 mins
take out the old put in the new
Was this helpful?
Thank you for voting!
Element burned out.
2 of 4 people found this instruction helpful.
  • Raymond from Ottawa, OH
  • Really Easy
  • Less than 15 mins
  • Screw drivers
First I removed the two screws that hold the element in place. I then pulled the element out aobut 3 inches and disconnected the wires.
Was this helpful?
Thank you for voting!
My oven sparked, then wasn't working, so I turned to the internet.
1 person found this instruction helpful.
  • Joan from Medford, OR
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I received the new element on the third day, followed simple directions, and voila! I'm baking again.
First I unplugged the stove. Important!. Then with a phillips head screwdriver I removed the two screws at the back of the oven. The transition from busted to new was easy because there was a slide-in connection to the wires, not screws. The best advice was sticking duct tape on the wires so they wouldn't go back into the inner sanctum before I was able to attach the new element. Hey, I'm a 72-year-old grandma, and it was easy!
Was this helpful?
Thank you for voting!
Bake element had burnt in half.
1 person found this instruction helpful.
  • Joyce from ROCHESTER, IN
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Watched the video that was available and followed the instructions. Unplugged the stove first,removed the old element, and put the new one in. Video was very helpful and the installation was very easy. Was done in about 10 minutes.
Was this helpful?
Thank you for voting!
Bake element burned out
1 person found this instruction helpful.
  • Richard from BOULDER, CO
  • Very Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Removed the failed bake element per the video linked in the Partselect email. Unlike the video on YouTube the PartSelect video shows that the bake element can easily be replaced through the oven door and it is not necessary to slide the range out and remove a rear panel.
Was this helpful?
Thank you for voting!
ELECTRIC BURNER SUPPORT FELL OFF AND BURNER SOMETIMES WOULD NOT COME ON.
1 person found this instruction helpful.
  • RICHARD from SHOW LOW, AZ
  • Very Easy
  • Less than 15 mins
Stuck the new one into the plugin.
Was this helpful?
Thank you for voting!
Element didn't heat at all
1 person found this instruction helpful.
  • Roger from PATERSON, NJ
  • Very Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Removed 2 screws, disconnected wires, attached wires to new element, put screws back. Turned oven on. Perfect.
Was this helpful?
Thank you for voting!
One of the broiler drawer guides broke
1 person found this instruction helpful.
  • Jeri from NEW RICHMOND, OH
  • Very Easy
  • Less than 15 mins
  • Screw drivers
All I had to do was pull the drawer out and screw on the new part! Awesome experience...and it was so easy to find the part on the website, everything is very clear and with pictures to ensure where the part belongs...who could ask for more?
Was this helpful?
Thank you for voting!
Oven gasket on door was very old. Oven door did not close properly.
1 person found this instruction helpful.
  • Margaret from Clarendon Hills, IL
  • Very Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Followed a simple video and completed this repair in just 5 minutes, gasket came out easily and the new one went in easily . Cleaning the oven door was the hardest part.
Was this helpful?
Thank you for voting!
All Instructions for the 3842
121 - 135 of 465