3841 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Element burned in half
1 person
found this instruction helpful.
-
James from Allyn, WA
- Really Easy
- Less than 15 mins
-
Screw drivers
Took two screws out unplugged the element and plugged the new one in and replaced the screws and turned the breaker back on. Works great...Piece of cake..jk
Was this helpful?
Thank you for voting!
The oven heating element burned out like a lit fuse!
1 person
found this instruction helpful.
-
Herbert from Neenah, WI
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed 2 phillips screws, unplugged 2 wires, threw away old element. Installation of the new element was just as easy but in reverse order. Piece of cake!
Was this helpful?
Thank you for voting!
Bake element would no longer heat up
1 person
found this instruction helpful.
-
Joe from Schertz, TX
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
I unplug the stove first. Then took off two screws that held the bake element in place. Pulled off the connectors using the pliers. Had to use pliers because they were really snug. Plug in the wires to the new base element. Crimped down the connectors a little bit to make sure they were snug. Inserted the bake element back into the
... Read more
holes at the back of the oven. Put the two screws back in. Plugged the oven back in and turned it on to make sure it worked. Lastly, tossed the old bake element in the trash. Really easy job. Glad I didn't pay anybody to do this.
Read less
Was this helpful?
Thank you for voting!
Element burned out.
1 person
found this instruction helpful.
-
Wayne from Marietta, GA
- Easy
- Less than 15 mins
-
Screw drivers
Turn off breaker.
Unscrew old element, disconnect wires.
Connect wires to new element, tighten screws.
Breaker back to ON.
Done.
Unscrew old element, disconnect wires.
Connect wires to new element, tighten screws.
Breaker back to ON.
Done.
Was this helpful?
Thank you for voting!
Bake Element Melted
1 person
found this instruction helpful.
-
Bert from S. Easton, MA
- Easy
- Less than 15 mins
-
Screw drivers
Unplugged stove, unscrewed element pulled element out about 3 inces and disconnected element. Took model of stove looked on line for part. PartSelect had the best price and easiest web site to order part. Ordered part about 4pm and received part in 2 days. Took element out of box plug into connections and screwed the element back in.
... Read more
Plugged stove in and worked perfect.
Read less
Was this helpful?
Thank you for voting!
snapped element
1 person
found this instruction helpful.
-
Paul from Yukon, OK
- Easy
- Less than 15 mins
-
Screw drivers
switch off the range. undo the two screws & unplug the two tabs. Replace with new element, connect two tabs, screw back in place. done!
recieved my replacement part the next day after ordering
recieved my replacement part the next day after ordering
Was this helpful?
Thank you for voting!
Element burned out.
2 of 4 people
found this instruction helpful.
-
Raymond from Ottawa, OH
- Really Easy
- Less than 15 mins
-
Screw drivers
First I removed the two screws that hold the element in place. I then pulled the element out aobut 3 inches and disconnected the wires.
Was this helpful?
Thank you for voting!
element had cracked
1 person
found this instruction helpful.
-
TONI from SALISBURY, NC
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
First I cut the power to the stove. Then I unscrewed the two screws. Pulled the element out a few inches. I had to use pliers to disconnect it from its wires. It was a very tight fit. Then I reconnected the new element. Cut the power back and and fired her up. Boy did she burn like fire.
Was this helpful?
Thank you for voting!
bottom bake element broken and burned
1 person
found this instruction helpful.
-
Carolyn S from white oak, NC
- Really Easy
- Less than 15 mins
-
Screw drivers
First throw the breaker on the stove. Remove two screws in back of oven then slowly pull out loosen the wire attachements ......got new part in 2 days just as simple reverse the removal directions.,,,I am over 60 female and it was simple.
Was this helpful?
Thank you for voting!
The old drip bowls were rusting, no chrome left
3 of 7 people
found this instruction helpful.
-
kathryn from piqua, OH
- Really Easy
- Less than 15 mins
Took the old ones out and put in the new ones! What I am so pleased about it that I just went online and at Parts Select website it was easy to find what I needed, a fair price and the 4 bowls arrived within 2 days!
Other Parts Used:
Was this helpful?
Thank you for voting!
My freezer door had a retainer bar that became disconnected at one end because the coupling broke.
1 person
found this instruction helpful.
-
Robert from SAN DIEGO, CA
- Really Easy
- Less than 15 mins
I slipped the coupling over the bar and then into a door slot. It was very easy.
Was this helpful?
Thank you for voting!
bakeing element caught fire.
1 person
found this instruction helpful.
-
Leticia from Sunnyvale, CA
- Really Easy
- Less than 15 mins
First I turned off power to the range at the fuse box (very important-The last time I didn't do this and ended up paying a repairman $150.00 to replace the damaged connectors). I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I then connected the new ele
... Read more
ment, pushed the element back in and replaced the screws. Turned the power back on and tested the element. The whole job took about 30 minutes because I had trouble disconnecting the old element. I used the flat end of the scrapper to push against the connector while I pulled the element out. Normally it would take only about 15 minutes.
Read less
Was this helpful?
Thank you for voting!
bulb out
1 person
found this instruction helpful.
-
Kenneth from Rowe, VA
- Really Easy
- Less than 15 mins
I ordered the part, within two days we had received it. My husband put the part in and I really don't know what he used doing so. All I know is that the light works now and we don't have to use the flashlight. Thanks a lot.
Was this helpful?
Thank you for voting!
Bake element had burnt in half.
1 person
found this instruction helpful.
-
Joyce from ROCHESTER, IN
- Really Easy
- Less than 15 mins
-
Screw drivers
Watched the video that was available and followed the instructions. Unplugged the stove first,removed the old element, and put the new one in. Video was very helpful and the installation was very easy. Was done in about 10 minutes.
Was this helpful?
Thank you for voting!
Couldn't find correct drip bowls that fit.
2 of 4 people
found this instruction helpful.
-
Lowell from Hardin, KY
- Really Easy
- Less than 15 mins
Removed old drip bowls, removed burners installed new drip bowls,installed burners. They fit perfect and I received them two days after ordering.
Other Parts Used:
Was this helpful?
Thank you for voting!