3751 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Old timer quit working.
7 of 14 people
found this instruction helpful.
-
John from Mesa, AZ
- Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Installed the new timer.
Was this helpful?
Thank you for voting!
the frame was broken and it made using the shelf for food storage difficult.
3 of 3 people
found this instruction helpful.
-
martha from Lehigh Acres, FL
- Very Easy
- Less than 15 mins
Emptied the lower area of food, removed the drawers and the removed the broken shelf frame. My glass was unbroken so after removing it from the broken frame and cleaning it, I just had to place it in the new frame and put it in the frig. Can't believe how easy and quick the whole process was. I can now utilized all that wasted space in my
... Read more
frig again.
Read less
Was this helpful?
Thank you for voting!
The unit cycles but does not achieve proper temperature
3 of 3 people
found this instruction helpful.
-
Anthony from COVINGTON, LA
- Very Easy
- Less than 15 mins
-
Screw drivers
Remove power from the unit. With short length #2 Phillips loosen and remove the two(2) screws on the control panel located center top of the refrigeration area. Slide the control panel back about 1/2 inch and allow it to dangle from its wiring harness. Pinch the locking tab on the harness connector with one hand and use the other hand to
... Read more
separate the two sides. A little force is required. Remove the control panel from the refrigerator and shut the refrigerator door. Examine and note the routing of the temperature probe (Silver colored flexible wire) take a picture for later reference. Remove the old and replace with new unit. route temperature probe like the replaced unit. Reverse the steps and reinstall the control panel. It is a good idea to also purchase and replace the defrost timer.
Read less
Was this helpful?
Thank you for voting!
Interior Light did not go on due to faulty switch
4 of 6 people
found this instruction helpful.
-
Robert from Coto de Caza, CA
- Really Easy
- Less than 15 mins
I ordered two switches, replaced both with a knife in 10 minutes. Interior light works, thanks.
Was this helpful?
Thank you for voting!
Broken freezer door shelf
3 of 3 people
found this instruction helpful.
-
Chris from E NORTHPORT, NY
- Very Easy
- Less than 15 mins
Just snapped in.
Was this helpful?
Thank you for voting!
the evaporator fan motor was making noise sometimes, but not all the time during the cooling cycle
3 of 3 people
found this instruction helpful.
-
Kenneth from SEATTLE, WA
- Really Easy
- 15 - 30 mins
-
Socket set
after watching how easy it was to get to the evaporator fan motor on u-tube, I took out the motor to inspect it......the motor had about 1/8 inch shaft end play and a slight amount of play on the shaft, the rubber grommets looked OK.....I then put it back together......since the motor was the only moving part in this location I figured it
... Read more
had to be the part making the noise, so I ordered a motor and 2 grommets …...the replacement motor also had 1/8 inch end play on the shaft, but no play on the shaft....I installed the new parts and it has been a week now and no noise.....SUCCESS!...….the shaft on the motor protrudes from the motor, and the fan is mounted about 1 1/4 inch away from the bearing in the motor and the fan is unsupported, so I ASSUME that the slight amount of play on the shaft caused some harmonics which caused it to make noise some of the time, but not all of the time......
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
NOISE FROM THE FREEZER SECTION OF THE REFRIGERATOR
3 of 3 people
found this instruction helpful.
-
Sarafina from DEWEY, AZ
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
1) TURNED POWER OFF FROM REFRIGERATOR 2) REMOVED THE FREEZER SHELF FIRST BY GENTLY TAPPING THE LEFT SIDE UP AND OUT THEN THE RIGHT SIDE UP AND OUT 3) REMOVED THE 2 PHILLIPS SCREWS HOLDING THE EVAPORATIVE FAN COVER IN PLACE 4) GENTLY PUSHED THE COVER UP AND MAKING SURE THE 2 CLIPS WERE NOT DAMAGED 5) VERY GENTLY PUSHED UP ON THE STYRO FOA
... Read more
M SHIELD GRASPING IT FROM THE BOTTOM, BE VERY CAREFUL NOT TO CRACK OR DAMAGE THIS 6) THEN REMOVED 4 OF THE PHILLIPS SCREWS HOLDING THE BACK PANEL 7) THEN REMOVED THE 2 SCREWS HOLDING THE FAN MOTOR IN POSITION ON THE BACK COVER AND LAID THAT ASIDE 8) I COULD THEN SEE THE MOTOR SO I UNCLIPPED THE RED/DARK WIRE CLIP FROM THE HARNESS WITH MY FINGERS, THEN TOOK MY NEEDLE NOSE PLIERS AND GENTLY PULLED UP ON THE GREEN GROUND WIRE 9) I THEN REMOVED THE 2 PHILLIPS HEAD SCREWS HOLDING THE MOTOR BRACKET TO THE WALL OF THE FREEZER 10) THEN REMOVED THE ENTIRE MOTOR AND PUT THAT ON THE KITCHEN TABLE 11) TOOK MY NEEDLE NOSE PLIERS AND VERY, VERY GENTLY PRIED OFF THAT LITTLE METAL RING HOLDING THE FAN BLADE ON (TRICKY SO LEFT UP GENTLY)...I BOUGHT ADDITIONAL IN CASE I DAMAGED IT 12) TOOK MY 5/16 NUT DRIVER AND UNSCREWED THE TOP METAL BRACKET HOLDING THE MOTOR 13) LIFTED THE MOTOR OFF AND LOOKED AT THE TOP AND BOTTOM GROMMETS TO SEE IF DAMAGED OR CRACKED (I BOUGHT ADDITIONAL GROMMETS IN CASE THEY WERE CRACKED OR DAMAGED, EASY FIX) 14) THEN ATTACHED THE NEW MOTOR AND BASICALLY SIMPLY DID EVERYTHING IN REVERSE TO INSTALL THE NEW MOTOR. MAKE SURE YOU KEEP YOUR SCREWS IN ORDER SO YOU CAN IDENTIFY WHICH PART THEY CAME FROM. MAKE SURE YOU DO NOT PINCH AND WIRES WHEN RE-INSTALLING THE MOTOR. SAVED ME A REPAIR PERSON CALL.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Broken Vegetable Drawer Shelf Frame
3 of 3 people
found this instruction helpful.
-
Laura from CRAIGVILLE, IN
- Really Easy
- 30 - 60 mins
I took the broken piece out and replace it with the new replacement shelf
Was this helpful?
Thank you for voting!
Plastic bracket broke so vegetable drawer would no longer stay in place
3 of 3 people
found this instruction helpful.
-
jim from CORNING, NY
- Really Easy
- 30 - 60 mins
Pipes out the glass from existing shelf while in place inside refrigerator. Remove broken shelf. Install new shelf. Clean and replace glass. Easy job thanks to finding the correct part from Part Select!
Was this helpful?
Thank you for voting!
Fan not working
3 of 3 people
found this instruction helpful.
-
joan from STERLING HTS, MI
- Easy
- 1- 2 hours
-
Screw drivers, Socket set
Took out old put new in. Watched a u tube, no problems
Other Parts Used:
Was this helpful?
Thank you for voting!
broken Vegetable drawer frame
3 of 3 people
found this instruction helpful.
-
Helen from PASO ROBLES, CA
- Really Easy
- 30 - 60 mins
Ordered the frame and put it in.
Was this helpful?
Thank you for voting!
intermittent loud screeching,,humming sound
3 of 3 people
found this instruction helpful.
-
LARRY. T from KNOXVILLE, TN
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
removed food from freezer section removed fan guard, partially remove ice maker, remove back panel, then fan assembly,disaasembled fan motor from brackets, fan from motor, grommet from bracket. assembled grommet in bracket, fan blade on motor, motor in bracket, fan assembly back in compartment, installed back panel,then ice maker, replace
... Read more
d fan guard and food. no more noise.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
noisy fan
4 of 6 people
found this instruction helpful.
-
ronald from springfield, VT
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
removed cover over fan, four screws. removed two screws ,that holds fan in place,removed two more screws that holds fan in bracket,then reinstalled
Was this helpful?
Thank you for voting!
Compressor would randomly not turn on. Fridge too warm sometimes.
3 of 4 people
found this instruction helpful.
-
Mackenzie from Williston, ND
- Really Easy
- 30 - 60 mins
-
Screw drivers
Replace temperature control. That fixed it. Also, removed plastic bag obstructing air vent in freezer which added performance. Fridge works good now.
Was this helpful?
Thank you for voting!
Freezer shelf bracket broke. .
3 of 4 people
found this instruction helpful.
-
George from Elkhart, IN
- Really Easy
- 30 - 60 mins
Took the bracket out of box and install it like the video showed me..very easy to install..
Was this helpful?
Thank you for voting!