3751 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
switchlight on my refrigerator was not working
5 of 10 people
found this instruction helpful.
-
Eileen from Coto de Caza, CA
- A Bit Difficult
- 30 - 60 mins
-
Pliers
I found instructions on the web about how to do this repair, so I ordered the part with confidence. But the instructions simply said "pull out the old switchlight". That was actually somewhat difficult as the clip on the side intended to hold the part in was stubborn. I eventually used a utility to slice off the clip. From that point,
... Read more
it was just a matter of plugging in the new switchlight , which was very simple.
Read less
Was this helpful?
Thank you for voting!
Replace the door gasket on the freezer door of my top-freezer refrigerator
3 of 4 people
found this instruction helpful.
-
Scott from NAPLES, FL
- Very Difficult
- 1- 2 hours
-
Socket set
Removed the door by removing the two screws holding it on. Do not try to do this repair with the door attached. Easily removed the old gasket. Getting the new one on the door was EXTREMELY difficult. I couldn't do it. After 90 minutes, I gave up and called my appliance repairman. When he arrived, he and I worked together to get the new ga
... Read more
sket on the door. It took 2 sets of hands to do this. It still took us about 40 minutes. My repairman had a few choice words about the design of the system holding the gasket on the door. Ditto for me. So the cost of my repair was doubled because I had to pay the repairman to help me attach the new gasket. I should have just bought a new fridge.
Read less
Was this helpful?
Thank you for voting!
Could not adjust temperature
3 of 4 people
found this instruction helpful.
-
Boyd from Blaine, WA
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Replaced temp controller
Was this helpful?
Thank you for voting!
Freezer was not freezing food.
3 of 4 people
found this instruction helpful.
-
Steve from Ridgecrest, CA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Inspected freezer because food was not freezing, getting cold, but not freezing. Noticed fan was not blowing air, but making a little motor noise, like it's trying to turn. Removed cover panel, and found the fan blade rubbing on the panel, fan shaft was worn out and very loose, wobley. That told me the fan needed to be replaced. Found par
... Read more
t on the GE Partselect website and ordered the parts via the website order process. This was easy. The parts were shipped quickley and were at my front door the next day. Couldn't believe it. The actual process was very easy: Remove cover, remove bracket holding fan motor, remove and replace motor, re-assemble parts. About 20-25 minutes from start to finish. Freezer is working like it's suppose to.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Fridge never cuts off.freeze everything inside of fridge.
3 of 4 people
found this instruction helpful.
-
Henry from DOUGLASVILLE, GA
- Very Easy
- Less than 15 mins
-
Screw drivers
To remove the temp sensor.2 Phillip head screws not remove the cover inside fridge .the temp control knob cover.removed that and unplugged switch.installed new switch.reinstalled cover.
Was this helpful?
Thank you for voting!
I never had Door shelving
3 of 4 people
found this instruction helpful.
-
Jennifer from TEXARKANA, AR
- Very Easy
- Less than 15 mins
Just popped them in their slots. Very easy and it made my refrigerator brand new again.. Thank you
Other Parts Used:
Was this helpful?
Thank you for voting!
Broken freezee door shelf
3 of 4 people
found this instruction helpful.
-
Sophie from WASHINGTON, DC
- Very Easy
- Less than 15 mins
Click shelf into place!
Was this helpful?
Thank you for voting!
During Hurricane Ike, frig. saw several inched of saltwater and sand underneath. AFter cleaning up, I tried to run and only the blower fan worked. It must have been just above the water. The compressor did not kick on. I looked at the lowest elec. connections and saw corrsion on the overload protect
3 of 4 people
found this instruction helpful.
-
ken from fulshear, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
This was after sitting idle for 9 mos. I simply pulled the part, ordered the same part and installed. Nothing more than a couple of screws and 2 wire connections. It now works great.
Was this helpful?
Thank you for voting!
Condensor fan blade cracked, blade was sheared off.
3 of 4 people
found this instruction helpful.
-
Bradley from Cedarburg, WI
- Easy
- Less than 15 mins
-
Pliers, Screw drivers
First, remove the cardboard cover on the back, lower portion of the refrigerator.
Next, locate the condensor fan motor assembly and blade. (Right side as you are facing)
Using a pliers, hold the shaft to keep it from turning and prevent damage to the motor. Using a screwdriver, slide the old ring compression on the b ... Read more lade shaft toward the motor (away from the fan blades) to loosen.
Remove old blade from the shaft by firmly grasping the motor shaft with a pliers (to prevent from damaging) and pull the blade assembly off.
Reverse the above steps to attach the new blade.
Next, locate the condensor fan motor assembly and blade. (Right side as you are facing)
Using a pliers, hold the shaft to keep it from turning and prevent damage to the motor. Using a screwdriver, slide the old ring compression on the b ... Read more lade shaft toward the motor (away from the fan blades) to loosen.
Remove old blade from the shaft by firmly grasping the motor shaft with a pliers (to prevent from damaging) and pull the blade assembly off.
Reverse the above steps to attach the new blade.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
missing part
3 of 4 people
found this instruction helpful.
-
james from humble, TX
- Really Easy
- Less than 15 mins
I order the small part and installed it myself, it was very easy with "part select". I will refer them and use them in the future. Thanks parts select.
Was this helpful?
Thank you for voting!
Shelf was cracked on both sides
2 of 2 people
found this instruction helpful.
-
Marcella from SPRINGFIELD, MA
- Really Easy
- Less than 15 mins
I first washed old shelf to make sure glass will easily slip out. Installed old glass and replaced.
Was this helpful?
Thank you for voting!
Broken shelf frame
2 of 2 people
found this instruction helpful.
-
Yvonne from FORESTVILLE, NY
- Really Easy
- Less than 15 mins
Easy
Was this helpful?
Thank you for voting!
Fixed shelf was cracked.
3 of 5 people
found this instruction helpful.
-
David from UNION CITY, NJ
- Really Easy
- Less than 15 mins
I popped out the old plastic shelf and slid in the new one. It was self explanatory and took less than one minute with no tools.
Was this helpful?
Thank you for voting!
Shelt guides were broken in vege drawer and same problem with meat pan guides
2 of 2 people
found this instruction helpful.
-
ART from WHITESTONE, NY
- Very Easy
- Less than 15 mins
Replaced drawer shelf and meat pan
Other Parts Used:
Was this helpful?
Thank you for voting!
Missing shelf
2 of 2 people
found this instruction helpful.
-
Phyllis from TUCKER, GA
- Very Easy
- Less than 15 mins
Went right on
Was this helpful?
Thank you for voting!