35HG Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Light burned out in upper oven
0 of 1 people
found this instruction helpful.
-
Shirley from Las Vegas, NV
- Really Easy
- Less than 15 mins
Screwed in light bulb and glass protector
Was this helpful?
Thank you for voting!
replaced oven lightbulb
0 of 1 people
found this instruction helpful.
-
peggy ann from forest city, NC
- Really Easy
- Less than 15 mins
very easy
Was this helpful?
Thank you for voting!
Bulb Replacement
0 of 2 people
found this instruction helpful.
-
Judith from Phoenix, AZ
- Really Easy
- Less than 15 mins
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
Was this helpful?
Thank you for voting!
old knob broken off inside
11 of 38 people
found this instruction helpful.
-
Kay from Gatesville, TX
- Very Difficult
- More than 2 hours
-
Pliers, Screw drivers
Repair not going well. Can't get the old part out. Have used needle nose plier and still can't get ahold of whats left of the part to pull out. Not for sure what to do next.
Was this helpful?
Thank you for voting!
Right-side oven door spring broken
-
Ted from Horseshoe Bend, AR
- Easy
- 30 - 60 mins
-
Screw drivers
Range is a 1967 model Maytag. First I removed drawer under oven, unplugged the range and pulled it out from the wall. Removed oven door by positioning it in the partly-open detent position, then pulled up to remove the door. Next I removed 7 screws per side panel: 3 in front and 3 in back, and one on top under cooktop, which retains the c
... Read more
ooktop hold-down clip. With side panels removed, I noted the oven door spring position on the intact left side, then replaced the right-side spring first using the same spring adjustment positions. As I replaced the spring, I applied lithium grease to the spring hook pivot points as well as the spring coils where they rub against the interior wall. I repeated the process on the left side. I reassembled the side panels, oiled the door hinges and reinstalled the oven door. Reinstalled range and bottom drawer. The oven door operates like new, and the new springs are totally quiet — good for another 47 years!
Read less
Was this helpful?
Thank you for voting!
The broiler element made a loud noise.I immediately turned the overn off. It kinda acared me.
-
Ann from Schertz, TX
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
My son-in-law installed the new element. First turn off the electricity and remove oven door. Then unscrew all connections to the element.The back electrical wires come out from the top back oven. The bracket screw faces the oven and the electrical wires are so short there is very little room for a screw driver (get the shortest one you c
... Read more
an find..abt as big as your thumb if possible).Once that was out the element came out with no problems.Then it's just reversing the step. Again, that back electical bracket is difficult to get to for install. Also, the new screws in our kit were Philips, but the old ones were flat so check those out before turning off the oven light.
Read less
Was this helpful?
Thank you for voting!
Easy installation
-
Jeremie from Freeland, WA
- Really Easy
- Less than 15 mins
-
Screw drivers
Unplug stove from outlet!! Removed screws (Phillips head) from prior element and pulled out enough to slip of the red and white wires. Keep in mind which side which is on and take old element out of oven. Put new element in and attach wires back on the same sides. Push back in and use screwdriver (Phillips head) to lift insulation to push
... Read more
wires and element prongs back. Put screws back in, close oven door and plug stove back in. Tested and works great!
Read less
Was this helpful?
Thank you for voting!
Light bulb failure
-
Grant from Alexandria, VA
- Really Easy
- Less than 15 mins
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Was this helpful?
Thank you for voting!
Oven would not heat up properly to set temperature
-
Max from Bothell, WA
- Really Easy
- Less than 15 mins
-
Screw drivers
The element appeared to have been damaged. I replaced the element with ease. However, I still have the same problem. The oven does not heat up to the set temperature. Information from the part select website is that it is more likely the long oven sensor. I ordered one and will provide the results after I have this sensor replaced wi
... Read more
th a new one.
Read less
Was this helpful?
Thank you for voting!
The drip pans needed replacing.
-
Alison from Carnation, WA
- Really Easy
- Less than 15 mins
Put in the new drip pan -- which are really nice shiny ones.
Other Parts Used:
Was this helpful?
Thank you for voting!
Dirty drip bowls
-
Paul from Carnegie, PA
- Really Easy
- Less than 15 mins
Just remove old bowls from range top and put new ones. That is all ... just super simple! :)
Other Parts Used:
Was this helpful?
Thank you for voting!
Dirty drip bowl
-
Paul from Carnegie, PA
- Really Easy
- Less than 15 mins
Remove old drip bowl from the range and put a new one back.
Was this helpful?
Thank you for voting!
The surface burner element burned out on my 20 year old Jenn Air electric stove.
-
Wanda from Riverton, WY
- Really Easy
- Less than 15 mins
It was so easy to order a new one from your company. And it arrived in less than a week! I slipped it into the electric outlet and it worked perfectly. THANKS. Wanda Major
Was this helpful?
Thank you for voting!
replacement of heating element for elec. stove
-
Erica from Ivyland borough, PA
- Really Easy
- Less than 15 mins
plugged it in to the spot where missing element was.
Was this helpful?
Thank you for voting!
needed a new drip bowl and couldn't find ons that fit exactly but you had it
-
Elsie from Garner, NC
- Really Easy
- Less than 15 mins
I removed the old one and put in the new one. Works great!!!!!!!!!!!!
Was this helpful?
Thank you for voting!