EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

35HA Magic Chef Range - Instructions

All Instructions for the 35HA
91 - 105 of 159

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
thermostat temprature bulb hanger clips
1 of 4 people found this instruction helpful.
  • Dwayne from Atlanta, GA
  • Really Easy
  • Less than 15 mins
snaped them into oven cavity attached temp bulb job complete
Was this helpful?
Thank you for voting!
Bulb Replacement
0 of 2 people found this instruction helpful.
  • Judith from Phoenix, AZ
  • Really Easy
  • Less than 15 mins
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
Was this helpful?
Thank you for voting!
Old surface element burned out.
0 of 2 people found this instruction helpful.
  • Royce from Rio Rancho, NM
  • Really Easy
  • Less than 15 mins
I ordered and received the replacement element, then unplugged the old one and plugged in the new one.

Job done.
Was this helpful?
Thank you for voting!
old knob broken off inside
11 of 38 people found this instruction helpful.
  • Kay from Gatesville, TX
  • Very Difficult
  • More than 2 hours
  • Pliers, Screw drivers
Repair not going well. Can't get the old part out. Have used needle nose plier and still can't get ahold of whats left of the part to pull out. Not for sure what to do next.
Was this helpful?
Thank you for voting!
Original burner stopped heating up
  • John from Nesconset, NY
  • Easy
  • 1- 2 hours
  • Pliers, Screw drivers
Unscrewed three screws securing the glass top. Lifted glass top and wedged it open. Took a picture of the current wiring. Removed old burner.Compared male contact points on new and old burner. Plugged new burner in appropriately. Note: The new burner is MUCH hotter than the old one.
Was this helpful?
Thank you for voting!
Burner did not heat, but element is ok.
  • Philip from Hull, MA
  • A Bit Difficult
  • 1- 2 hours
  • Pliers, Screw drivers
The Burner Control Switch - 250V Part Number: PS2089409 that this site recommended was the right part for this older range. Had to remove screws to pull out the front panel with knobs, but it only pulls out a couple inches due to wires so it is tight to remove old switch. The five tabs are not in same spot so go by the labels and the wi re lugs fit just fine, and the knob snapped right on and works great. Thank You!
Was this helpful?
Thank you for voting!
Lower left Surface Element burnt
  • John from Nashville, TN
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
1. Remove power from unit. 2. Removed 1/4" sheet metal screw from lower blower vent tube. 3. Lifted the unit above the counter and placed two 1x2" boards between the unit and counter. To remove the Stove Top to get access to the Element you must remove 8 each 1/4" sheet metal screws from the bottom side of the Stove Top attaching flange. 3 each screws on the forward and aft side and 1 each on the left and right side. (Note, the 8 each 1/4" attaching screws are at the top of the Stove Top attaching flange.) 4. Remove the Vent Grill and locate the 2 each cross point screws on the center left and right side of the opening. (Note. Due to the limited space, I used a right angle cross point driver.) 5. Remove Stove Top. 6. Tag electrical connections. Remove and replace Element. 7. Turn on power and check Element. Remove power and Reassemble Unit.
Was this helpful?
Thank you for voting!
The broiler element made a loud noise.I immediately turned the overn off. It kinda acared me.
  • Ann from Schertz, TX
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers
My son-in-law installed the new element. First turn off the electricity and remove oven door. Then unscrew all connections to the element.The back electrical wires come out from the top back oven. The bracket screw faces the oven and the electrical wires are so short there is very little room for a screw driver (get the shortest one you c an find..abt as big as your thumb if possible).Once that was out the element came out with no problems.Then it's just reversing the step. Again, that back electical bracket is difficult to get to for install. Also, the new screws in our kit were Philips, but the old ones were flat so check those out before turning off the oven light.
Was this helpful?
Thank you for voting!
Right-side oven door spring broken
  • Ted from Horseshoe Bend, AR
  • Easy
  • 30 - 60 mins
  • Screw drivers
Range is a 1967 model Maytag. First I removed drawer under oven, unplugged the range and pulled it out from the wall. Removed oven door by positioning it in the partly-open detent position, then pulled up to remove the door. Next I removed 7 screws per side panel: 3 in front and 3 in back, and one on top under cooktop, which retains the c ooktop hold-down clip. With side panels removed, I noted the oven door spring position on the intact left side, then replaced the right-side spring first using the same spring adjustment positions. As I replaced the spring, I applied lithium grease to the spring hook pivot points as well as the spring coils where they rub against the interior wall. I repeated the process on the left side. I reassembled the side panels, oiled the door hinges and reinstalled the oven door. Reinstalled range and bottom drawer. The oven door operates like new, and the new springs are totally quiet — good for another 47 years!
Was this helpful?
Thank you for voting!
Easy installation
  • Jeremie from Freeland, WA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Unplug stove from outlet!! Removed screws (Phillips head) from prior element and pulled out enough to slip of the red and white wires. Keep in mind which side which is on and take old element out of oven. Put new element in and attach wires back on the same sides. Push back in and use screwdriver (Phillips head) to lift insulation to push wires and element prongs back. Put screws back in, close oven door and plug stove back in. Tested and works great!
Was this helpful?
Thank you for voting!
surface burner failure
  • Gerald from Hot Springs Village, AR
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
Lifted the range top about 2 1/2 inches, removed the ceramic top and replaced the burner. Tested the burner before replacing the top. Everything worked fine.
Was this helpful?
Thank you for voting!
Burner was always in high temperature.
  • Dennis from Oak Lawn, IL
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Pulled the range away from the wall and took out all the screws of the back panel. I had two different screws. Removed the dial and took two screws out behind the dial. Carefully removed the wires and placed them on the new switch. Screwed switch to panel, replaced dial and put the back panel back on range. Pushed range back into place.
Was this helpful?
Thank you for voting!
I had a power serge and it burned the Plug at the termial block and melted a few wire.
  • Robin from Vanderbilt, PA
  • Really Easy
  • 15 - 30 mins
  • Socket set
After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.
Was this helpful?
Thank you for voting!
Burner stayed on "high", could not adjust heat
  • Deborah from Hodgen, OK
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
I UNPLUGGED STOVE, removed panel covering the controls, removed the knob on front and the two screws there that hold the control in, inserted new control and replaced the two screws on the front that hold it onto the stove, used needle nosed pliers to unplug one connection at a time from the old control and onto the new control in the bac k. When I had all connections plugged onto the new control I re-installed the panel cover with a screwdriver, plugged the stove back in, and the burner is now working good as new!
Was this helpful?
Thank you for voting!
Broken Door Spring
  • Matthew from Chippewa Falls, WI
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Slid oven out from counters. On each side there are 3 screws on the front and three screws on the back holding the side piece on. Once off, the spring was very easy to get at and replace. I had only one broken, but replaced both anyways. I think it took longer to clean the sides of the oven that haven't been touched in years than to r eplace the springs. This job was very simple and easy.
Was this helpful?
Thank you for voting!
All Instructions for the 35HA
91 - 105 of 159