35HA Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Drip bowls were burned and tacky
473 of 483 people
found this instruction helpful.
-
Donna from Dallas, TX
- Really Easy
- Less than 15 mins
First I removed the old bowls and replaced them with the new.
Other Parts Used:
Was this helpful?
Thank you for voting!
Drip bowls needed to be replaced
455 of 546 people
found this instruction helpful.
-
John from Chester, VT
- Really Easy
- Less than 15 mins
took old bowls out, put new bowls in, took a coffee break
Other Parts Used:
Was this helpful?
Thank you for voting!
Old drip pans stained
218 of 427 people
found this instruction helpful.
-
Linda from Atlanta, GA
- Really Easy
- Less than 15 mins
Replaced old drip pans with new ones - very easy - even a 68 yr old lady can do it!!
Other Parts Used:
Was this helpful?
Thank you for voting!
We needed new drip pans and no one carried the model we needed
67 of 71 people
found this instruction helpful.
-
sylvia from ventnor city, NJ
- Really Easy
- Less than 15 mins
we removed the old pans after first removing the electric heating element and simply inserted tne new pans
Other Parts Used:
Was this helpful?
Thank you for voting!
Burned terminal block and filter board
95 of 208 people
found this instruction helpful.
-
Joseph from Decatur, GA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set, Wrench set
Removed and replaced above named parts, rewired.Be sure to tighten all nuts that secure wires. I believe this is what caused the problem.
Was this helpful?
Thank you for voting!
replaced heating element on flat surface stove top
35 of 48 people
found this instruction helpful.
-
dennis from assonet, MA
- Really Easy
- 15 - 30 mins
-
Nutdriver
I removed 4 screws and then lifted up the top it gave me access to the element I followed the direction that came with the element (very clear to follow) removed and installed the new element and it worked fine. Remember to unplug the stove if it is electric this is not in the instructions.
Was this helpful?
Thank you for voting!
Small Element On Counter Top Range Not Heating.
17 of 20 people
found this instruction helpful.
-
Brian E from Waldorf, MD
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
1. Turned off power to trouble shoot the counter top range elements. 2. Raised the counter top up to work on it and slid two evenly placed wooden slats under the bottom of the housfor stability so it would not fall backdown into the counter top cut-out. 3. With a 1/4" nut driver removed the 10 hex-head screw that were holding the blac
... Read more
k glass top in place, pulled off the 4 . Control knobs and carefully removed the glass cover and carefully seet it aside in a safe place. 5. A visual inspection of the non working element showed that it had a burn out spot causing it not to heat. 6. Got the model number of the appliance and checked the internet for parts suppliers, chose parts elect because they had the part in stock and could overnight it for reinstallation the next day, part did arrive the next morning. A visual inspection show that it was the correct part and it would be a like for like swap out. 7. Prior to replacing the element check to see that the electrical power was still off at the circuit breaker, made a quick sketch of the wiring and identified the wires so that they would be reterminated at the same points. 8. Using the needle nose pliers pulled off the 4 stake on terminations. 9. Lifted out the 6" from the body of the unit , removed the 4 phillips screws holding parts what were to be transfered onto the new element. 10. Transfered parts onto the new element, reinstalled the element into the body of the unit, reinstalled the 4-stake-on wires to there appropriate terminals and verified with previous wiring sketch. 11. Reinstalled the glass top, 10 screw holding it in place and the 4-control knobs. 12 . Turned main power to the unit back on and turned on the replaced element, it work correctly, also checked the other 3 elements to make sure that they were working correctly. 13. When the unit had cooled, removed the wooden slats and lowered the counter top back into its cut-out making sure not to damage the glasstop. Job complete.
Read less
Was this helpful?
Thank you for voting!
Element burned out
18 of 28 people
found this instruction helpful.
-
Anita from Hudson, CO
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Unplug Stove removed screws pulled out
element. Lifted off the wires with a pliers they slid
onto the element ends that were pointed up
was very easy.
element. Lifted off the wires with a pliers they slid
onto the element ends that were pointed up
was very easy.
Was this helpful?
Thank you for voting!
Rubber gasket failed due to age
14 of 18 people
found this instruction helpful.
-
Mary from Woodland, WA
- Really Easy
- Less than 15 mins
-
Screw drivers
I learned that I could clean the window in the oven door. In taking it apart I saw that the gasket had fallen into the oven door. I found the part online, it arrived in three days. I removed the metal part of the door, removed what was left of the old gasket and put in the new one. Put the metal part of the door back on, and it was as g
... Read more
ood as new.
Read less
Was this helpful?
Thank you for voting!
spring broke on one side of door hinge
14 of 20 people
found this instruction helpful.
-
Travis from Lexington, OK
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Pulled the stove out, removed the sides and attatched the new springs( replaced both while the stove was out). Worked like new and put the stove back.
Was this helpful?
Thank you for voting!
Baked on sauce
12 of 16 people
found this instruction helpful.
-
Julie from Newnan, GA
- A Bit Difficult
- More than 2 hours
Used cooktop creme, oven cleaner and Mr. Clean sponges. After many days of working on the surface, we were able to remove 99% of the sauce.
Was this helpful?
Thank you for voting!
Burner not working
12 of 18 people
found this instruction helpful.
-
Warren C from Slidell, LA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
First thing- I cut off power to the range. I then removed two screws to allow the cook top to be lifted. I marked the wiring and replaced the burner. Reapplied power and started cooking!
Was this helpful?
Thank you for voting!
Purchased home but stove had no broiler pan.
16 of 33 people
found this instruction helpful.
-
Raymond from BLOOMINGTON, MN
- Very Easy
- Less than 15 mins
Purchased 2 piece broiler pan from this site
Was this helpful?
Thank you for voting!
Broiler unit would only heat on one side
8 of 9 people
found this instruction helpful.
-
Lawrence from Morganton, NC
- Really Easy
- 1- 2 hours
-
Screw drivers
Removed the screws that held the element and disconnected it. Placed the new element in the proper place, connected the wiring, and replaced all the screws. The unit worked beautifully, and all is well. My wife is happy.
Was this helpful?
Thank you for voting!
The oven and ranges would not heat up and an F9 error was displaying on the Oven Screen.
7 of 7 people
found this instruction helpful.
-
Jared from UNION GROVE, AL
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
So, the F9 error indicates a electrical power issue. First I pulled the oven out and verified I had 240 volts at my outlet.
Then I removed the fire panel over the terminal block and the issue was apparent. The nuts on the terminal block were corroded. This had cause the resistance in the connection to raise and burn up the ... Read more wire to my oven plug at the terminal block.
I removed the whole back panel and everything else seemed OK visually.
1. I go new connectors for the oven plug, stripped the wires, and crimped on the new connectors.
2. The terminal block DOES NOT come with the nuts to connect the wire to the terminal block. Mine were so corroded they had to be replaced. So I went and purchased the correct ones and installed the terminal block and reconnected all the wires.
3. I applied some dielectric grease to the connections through out the process of reinstalling to prevent it from happening in the future.
Then I removed the fire panel over the terminal block and the issue was apparent. The nuts on the terminal block were corroded. This had cause the resistance in the connection to raise and burn up the ... Read more wire to my oven plug at the terminal block.
I removed the whole back panel and everything else seemed OK visually.
1. I go new connectors for the oven plug, stripped the wires, and crimped on the new connectors.
2. The terminal block DOES NOT come with the nuts to connect the wire to the terminal block. Mine were so corroded they had to be replaced. So I went and purchased the correct ones and installed the terminal block and reconnected all the wires.
3. I applied some dielectric grease to the connections through out the process of reinstalling to prevent it from happening in the future.
Read less
Was this helpful?
Thank you for voting!