35HA Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Front left burner quit after bright flash under glass top
11 of 19 people
found this instruction helpful.
-
Brian L. from Wilkes-Barre, PA
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Screw drivers
I ohmed out the burner element that wasnt working and found it was open. I ordered a new element thru PartSelect and installed it in the stove. I powered up the stove and turned on the burner but it didnt get hot. After a bit of testing I found that the new elements safety overtemp terminals werent in the same configuration as the origina
... Read more
l unit. I made some wiring adjustments and the burner was operating properly. Thanks PartSelect
Read less
Was this helpful?
Thank you for voting!
Door Spring Broke
7 of 9 people
found this instruction helpful.
-
Thomas from Van Nuys, CA
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Removed 7 screws on sides and one on top of stove. Replaced both springs (only one was broken but did both). Took around 15 to 30 minutes from start to finish.Fastest shipping in history during holidays without paying anything extra.
Was this helpful?
Thank you for voting!
Stove top wouldn't come on. Oven couldn't go higher than low heat
7 of 9 people
found this instruction helpful.
-
Peter from FREDERICK, MD
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
Had a technician from Home Advisor to check the problem out with my Whirlpool Double oven(1 1/2 old). Paid $60 to find the problem. According to the technician problem was control board and cost of labor and parts $465.00
Jumped on Part Select website, placed a question with my stove problem through the chat. Immediately they answer ... Read more ed my question and told me the problem was the Terminal Block. Cost of part and shipping $25.00. Replaced it myself and everything works fine.
Thank you, Thank you Part Select for your help and honesty.
Sincerely
Peter from Maryland
Jumped on Part Select website, placed a question with my stove problem through the chat. Immediately they answer ... Read more ed my question and told me the problem was the Terminal Block. Cost of part and shipping $25.00. Replaced it myself and everything works fine.
Thank you, Thank you Part Select for your help and honesty.
Sincerely
Peter from Maryland
Read less
Was this helpful?
Thank you for voting!
electric coils would not stay flat as drip pans were incorrect fit
6 of 7 people
found this instruction helpful.
-
Janet from Philadelphia, PA
- Really Easy
- Less than 15 mins
replaced drip pans with correct type
Other Parts Used:
Was this helpful?
Thank you for voting!
the left front burner burned out & none of the lights to show if a burner was hot would come on.
5 of 5 people
found this instruction helpful.
-
Richard from Fair oaks Ranch, TX
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Socket set
FIrst we found the power source ( this took us awhile) and cut the power at the fuse box. then we unplugged the cooktop and started to take out screws. It turned out the screw removal had nothing to do with the stove top coming out. We took the taping knife & pried it under a corner and lifted. the cook top was just sitting on the count
... Read more
er.
The hardest part of the whole job was holding the cook top because we did not disconnect the downdraft fan other than to pull the tape off the vent & fan. Now we could undo the rachet screws that held the glass top to the cook top & remove it.
Theburner was simply a matter of pulling connections loose & placing them on to the new one. The clips that hold the burner in place were removed w/ a screwdriver & replaced on to the new burner. Watch for the numbers on the burner underside to know where to reattache the clips. the unit that lights up to show that a burner is hot would not come off, but we managed to remove
the plastic part even though the clip screw would not loosen, and since it only had to float near by we used the unused wire included in the new part to hold it in place. Putting the unit back together was not too hard, but it took us a little while to get it all lined up. Be carefull of what ever you work on, the downdraft fan scratched up the counter top that we were working on. we started with cardboard under it & should have continued, we did not want to try & remove the fan. Then we put it back in the counter opening & plugged everything back in & to our amazement ( we are not handy people) it worked! the lights that had refused to work when one unit was burned out now worked on all four units. thank you partselect, we were able to do the repair with what you sent.
The hardest part of the whole job was holding the cook top because we did not disconnect the downdraft fan other than to pull the tape off the vent & fan. Now we could undo the rachet screws that held the glass top to the cook top & remove it.
Theburner was simply a matter of pulling connections loose & placing them on to the new one. The clips that hold the burner in place were removed w/ a screwdriver & replaced on to the new burner. Watch for the numbers on the burner underside to know where to reattache the clips. the unit that lights up to show that a burner is hot would not come off, but we managed to remove
the plastic part even though the clip screw would not loosen, and since it only had to float near by we used the unused wire included in the new part to hold it in place. Putting the unit back together was not too hard, but it took us a little while to get it all lined up. Be carefull of what ever you work on, the downdraft fan scratched up the counter top that we were working on. we started with cardboard under it & should have continued, we did not want to try & remove the fan. Then we put it back in the counter opening & plugged everything back in & to our amazement ( we are not handy people) it worked! the lights that had refused to work when one unit was burned out now worked on all four units. thank you partselect, we were able to do the repair with what you sent.
Read less
Was this helpful?
Thank you for voting!
light bulb in water ice freezer door went bad
8 of 14 people
found this instruction helpful.
-
Carl from RIVERSIDE, CA
- Very Difficult
- More than 2 hours
-
Screw drivers
I didn't. Don't know how to get to light bulb to change it for this specific model
Was this helpful?
Thank you for voting!
electric burner burned out
6 of 9 people
found this instruction helpful.
-
Paul from Foley, AL
- Really Easy
- Less than 15 mins
This is the second time PartSelect came through for me. If it hadn't been for you guys, I'd have had to buy a new Jenn-Air cooktop, because ours is nearly 30 years old. About two years ago, I bought a new two-burner cartridge, which installed without tools in about one minute. But a few weeks ago, we lost the burner in the other cartri
... Read more
dge. I emailed PartSelect, and even though I gave them my obsolete model number, a helpful service rep managed to find me the part number of the correct burner, so I was able to place my order. Once the part arrived, there was no problem replacing the burner. This is a simple operation we've performed many times when we need to remove the burner for cleaning.
Read less
Was this helpful?
Thank you for voting!
Store-bought drip bowls wouldn't fit.
5 of 6 people
found this instruction helpful.
-
Sharon from Yacolt, WA
- Really Easy
- Less than 15 mins
My elements just plug in so all I had to do was pull them out and replace the drip bowls. They fit perfectly!
Other Parts Used:
Was this helpful?
Thank you for voting!
burner fell apart
5 of 7 people
found this instruction helpful.
-
Barbara a from Huntington, NY
- Really Easy
- Less than 15 mins
Plugged in the new burner, which we received in one day.We were delighted with the quick service
Was this helpful?
Thank you for voting!
Timer know would no longer set the time...
5 of 7 people
found this instruction helpful.
-
Rachael from Adams, MA
- Very Difficult
- More than 2 hours
-
Screw drivers
I removed the screws holding the bezel, removed the control panel frame, unhooked the four wires from the timer, and removed the timer. I cut the glue holding the circuit board into the frame and removed the circuit board. I unsoldered the faulty encoder switch, dissassembled the switch, determined the correct specifications for the swit
... Read more
ch, and ordered the nearest equivalent from an electronics supplier. I modified the new encoder to accept the shaft from the old encoder and I re-drilled the circuit board to fit the new encoder. I then soldered and wired the encoder, reversing the wires to correct the direction of rotation. I then reinstalled everything and added the knob purchased from partselect.com. Now it works. Tough repair - not for the faint of heart or those of average skill. But for the record, installing the knob was of course child's play and took only a moment.
Read less
Was this helpful?
Thank you for voting!
Replacement of broil element in wall oven
4 of 4 people
found this instruction helpful.
-
David from San Rafael, CA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
In principle it should be easy to replace the broil element in the wall oven, after unscrewing the supports for the back and front of the element (see other postings for details). The difficulty is with the ground screw, which is inconveniently only accessible from behind close to the back wall of the oven. A very short phillips screw d
... Read more
river is required, but designed so that good torque can be applied for unscrewing and replacing. The newly designed ground connector on the latest replacement elements makes life a little easier, but still be prepared to work slowly and carefully to complete the replacement. Note the new ground screws supplied only work with a flat-blade screw driver, not a phillips-type.
Read less
Was this helpful?
Thank you for voting!
Indicatror Light For 6" Burner Quit Working
5 of 7 people
found this instruction helpful.
-
NANCY from LITTLETON, CO
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Ok this is a glasstop jenn air cce3531b, 5 burners, 11 years old. I am computer data entry employee and 56 years old. I have never done repairs myself in the past but decided to try. I ordered a new burner and indicator light as I wasnt sure which to replace. I found the main breaker and shut it off. I lifted the stovetop out of the
... Read more
counter opening by pushing it through the bottom and placed it on the counter with a towel under it, I had plenty of room to work so that was very easy. I used a nutdriver set to remove 12 screws and lifted off the top very carefully and placed it in the other room , since I had to repair unit thought I would also clean and replace the foam tape around the perimeter of the glasstop. Ok now I unscrewed 4 more screws with the nutdriver and replaced the indicator light, that took about 6 minutes so far. Then I turned the breaker back on and tested and it did not work. Turned breaker back off ,now I replaced the burner by lifting it out of the opening very easily, unscrewed with philips screwdriver 2 screws and the new burner was exactly the same as the existing one so I just slid the old connections off one at a time and replaced them as I went along onto the new burner, screwed it back into place and turned the breaker on and tested it and it worked. I now turned the breaker back off and took off the old foam tape from the glasstop and replaced with new, fit it back onto the base and screwed the 12 screws back in and placed it back into the counter opening and turned breaker back on and now all is fixed and I saved $100 dollars in labor fees. This took 35 minutes and was easy for me. Thanks you partselect
Read less
Was this helpful?
Thank you for voting!
Left front burner went out.
5 of 7 people
found this instruction helpful.
-
Donald from North Highlands, CA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Removed 8 screws of retainer holding glass top to box.. Pulled 5 knobs and glass top and set aside. Popped 2 retaining clips holding burner , removed them and transferred to new burner (#12 and #48 position). Used wide blade screwdriver to facilitate removing terminals from old burner and attached terminals to new burner.Popped retaining
... Read more
clips into crossbeam, put glass top on and 8 screws back into retainer. Works great.
Read less
Was this helpful?
Thank you for voting!
The 6" heating element stop working on the stove top.
4 of 4 people
found this instruction helpful.
-
JULIUS from JACKSON, MI
- Very Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
First I reviewed a video on YouTube by this site. Even though the range on the video was not the same as mind, it gave me an idea on what to do. I proceeded to pull the rang out from the wall and disconnected the power plug. Next I removed two screws from the back located on the left and used a flat blade screw driver to depress two brack
... Read more
ets on the front to release the glass top panel. I unplugged the wiring harness and disconnected the grounding wire and took the glass panel off and laid it upside down on the kitchen table. I removed the old heating element first by unplugging the wiring and removing the brackets that held it in place. Installed the new one, plugged in all wirings, brackets, screws and replace the top back on the stove.
Read less
Was this helpful?
Thank you for voting!
One of the electric stove top elements had burnt out
4 of 5 people
found this instruction helpful.
-
Anthony from Palmyra, VA
- Really Easy
- 30 - 60 mins
-
Screw drivers
The repair was very easy. There were 3 screws under the front lip which had to be removed. This allowed the smooth glass top to be removed, tilt and pull forward. This exposed the burners and the unit I purchased was a direct replacemt for the burnt unit. All I had to do was remove the electrical clips from the old unit and put them on th
... Read more
e new unit. There were 3 spring elements, each with 2 screws, which held the unit in place.
Read less
Was this helpful?
Thank you for voting!