EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3563 Magic Chef Range - Instructions

All Instructions for the 3563
91 - 105 of 421

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Bake element burned out
1 person found this instruction helpful.
  • Donald from Tomahawk, WI
  • Really Easy
  • 15 - 30 mins
Very simple fix--unpugged two fittings in the back of oven plugged in the new element and it was done.The Best part was that the element burned out on a Sunday and I ordered the part that day and it shipped on Monday and received part on Wed AM.This is the second time I've had to replace the element and by ordering through Part Select I s aved $24.00 versus buying it from an appliance store.

Don Samuelson
Was this helpful?
Thank you for voting!
lens light was broken and missing.
1 person found this instruction helpful.
  • Allan from Rolla, MO
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers
Removed the cooktop using screwdriver. Pushed lens-light into cooktop hole.It was difficult to do and was where I spent most of my time. Next time I will spray bottom of lens- light with silicon so it goes in easier. I stood cooktop up on its side and inserted the red light assembly onto the lens-light. Reinstalled cooktop < br />and turned electrical power on.
Was this helpful?
Thank you for voting!
Oven door was locked, couldn't set oven temps
1 person found this instruction helpful.
  • William from Nashville, TN
  • Easy
  • 15 - 30 mins
  • Screw drivers
Got a bent metal coathook to temporarily release the oven door, removed the screws from the old probe, inserted the new one, and hooked it up, using the one of the plug adapters provided. Problem solved! The oven door latch was now disengaged, the oven would now accept temperature inputs, and the rear cooling fan (which wouldn't shut off) now turned off. That's a lot of things working better for less than $50!
Was this helpful?
Thank you for voting!
Lower burner not heating:
1 person found this instruction helpful.
  • John from Fishers, IN
  • Easy
  • 15 - 30 mins
  • Screw drivers
Ordered element and recieved in two days(yea). Removed back cover from unit. Removed two wire slide on wire clips. Then went inside oven cavity and removed two screws holding element intact. The element slid out. Installed element, re-installed two screws to hold element intact. Attached wire clips back on to element, re-attached back cover. Plugged unit back in and it worked perfectly. Eazy-peezy lemon squeezy.

John
Johnny on the Spot Home Repairs
Fishers, Indiana 317-997-3600
Was this helpful?
Thank you for voting!
Bottom Element Burned out
1 person found this instruction helpful.
  • Robert from Jacksonville, FL
  • Easy
  • 15 - 30 mins
  • Screw drivers
Turned off all power to range.
Removed two Philip head screws
Gentle pulled unit Element forward
Removed two push on connectors
(Do not let wires fall back into oven holes)

Reversed the process.
Was this helpful?
Thank you for voting!
burner receptacle failed (stove over 30 years old)
1 person found this instruction helpful.
  • BETH from COUNCE, TN
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Took out burner (pulls out) Took out one screw that holds recep. in, cut the two old wires and attached new wires with wire nuts included in the new package.
Was this helpful?
Thank you for voting!
Bake element burned out
1 person found this instruction helpful.
  • Richard from BOULDER, CO
  • Very Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Removed the failed bake element per the video linked in the Partselect email. Unlike the video on YouTube the PartSelect video shows that the bake element can easily be replaced through the oven door and it is not necessary to slide the range out and remove a rear panel.
Was this helpful?
Thank you for voting!
Oven would not hold temperature, not turn on, and would shut off during use.
1 person found this instruction helpful.
  • John from Arvada, CO
  • Very Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Extremely simple repair to make. Move stove away from wall and disconnect power. Remove the oven racks. Remove the rear sheet metal panel covering the wiring harnesses. Caution: Sharp edges and corners on sheet metal.Sensor is located in upper left corner on rear oven wall. Using a long-shafted #2 Philips screwdriver, remove the two Phili ps head screws and gently pull the sensor 1" away from the oven wall. At this point, it will help to have an assist from someone while you are behind the range. Have the assistant gently tug on the sensor while you watch for wires moving on the rear of the range. After locating the sensor wires, gently disconnect the plastic connector clip. Note: plastic connectors become brittle with age and exposure to heat Move to front of range and gently remove sensor from rear wall by pulling the wiring through the oven wall. Before inserting the new sensor wire through the oven wall, "dry fit" the wiring connectors to see that the new sensor is a correct connection. Make connection, and secure the sensor to the rear oven wall with the two screws. Install racks, reinstall rear sheet metal panel, and connect the power. Set the oven baking temperature to a moderately low temp, 300 - 350 deg. to test the new sensor.
Was this helpful?
Thank you for voting!
Element didn't heat at all
1 person found this instruction helpful.
  • Roger from PATERSON, NJ
  • Very Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Removed 2 screws, disconnected wires, attached wires to new element, put screws back. Turned oven on. Perfect.
Was this helpful?
Thank you for voting!
No problem installing the sensor
1 person found this instruction helpful.
  • tommy from FAYETTEVILLE, NC
  • Very Easy
  • Less than 15 mins
  • Screw drivers
I removed the two mounting screws and pulled the harness through the opening unsnapped the sensor from the harness and installed the new sensor i didn't have to used the adapters the new sensor fitted
Was this helpful?
Thank you for voting!
The Baking Element won't heat to bake.
1 person found this instruction helpful.
  • Kiara from JACKSONVILLE, FL
  • Very Easy
  • Less than 15 mins
  • Screw drivers
I had the problem before and had to call in a Tech to repair the baking element in my oven. It cost me $150.00 for the repair. This time I decided to do the repair myself, so I went online and found this site The instruction video made it very easy. I am very proud of what I was able to do without calling a Tech. My oven works like new, I t only cost less than $40.00 for the total repair. I am so glad this site were there when I needed them.. Thanks a Lot..
Was this helpful?
Thank you for voting!
replace broken bake element
1 person found this instruction helpful.
  • Frances from MOREHEAD, KY
  • Very Easy
  • 15 - 30 mins
  • Screw drivers
Unplugged the range. Took our the oven shelves. Unscrewed the bars holding the broken bake element to the back of the oven wall. Gently pulled out the wiring to which the bake element is attached. Slipped the ends of the broken bake element off the ending on the wiring. Then slipped the ends of the new bake element over the ends on the wiring. Then pushed the wiring with attached bake element back into their position behind the oven wall and attached the bars holding the bake element to the back of the oven wall. This is really easy because it is exactly like the on-line video, for I am a 75 year old female with little technical experience.
Was this helpful?
Thank you for voting!
"F3" error message and no oven heat
1 person found this instruction helpful.
  • Pat from PAYSON, AZ
  • Very Easy
  • 15 - 30 mins
  • Screw drivers
Unplugged the range, removed screws holding the old sensor. When I pulled it out, the wire connecting to the sensor was completely broken through,therefore I could not just pull the wire to get to the connector. Unscrewed one side of back panel to access the connector. Pushed the connector and wire of the new sensor through the hole ( and behind the insulation), disconnected the old sensor and connected the new one. Re screwed the new connector in place plus rescrewed the back panel. Plugged the range in and - Viola! Everything now works like a charm and I have my oven back. Easy-Peasy. Oh - I am an older female with very limited DYI experience. I just saved myself $650.00!
Was this helpful?
Thank you for voting!
The bake oven element burned out
1 person found this instruction helpful.
  • Robert from LEXINGTON, MA
  • Very Easy
  • 15 - 30 mins
  • Screw drivers
Removed two screws and disconnected the element. Reconnected the new element and reinstalled the screws
Was this helpful?
Thank you for voting!
My oven door seal had dried rotted
1 person found this instruction helpful.
  • Anita from ELKTON, VA
  • Really Easy
  • 15 - 30 mins
  • Pliers
I took pliers to get the old one off, and popped the new one back in its place, and it fit perfect.
Was this helpful?
Thank you for voting!
All Instructions for the 3563
91 - 105 of 421