EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3563 Magic Chef Range - Instructions

All Instructions for the 3563
76 - 90 of 421

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Bake element caught on fire
2 of 2 people found this instruction helpful.
  • Dan from TomRriver, NJ
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
I got the run around about my HARWICK stove at several part stores. Like they all said the same thing (cant look it up just bring it down) So i did and then they would say, what's the model number. ERR! SO my wife found parts select on the web and they beat the three price quotes I got. First turn the power off to the stove!!! The repair was simple. Just remove the two screws on both side's and pull the element out but just enough for the wire's to show. Disconnect the two wire's and pull the element out. Reverse the processes but when wire's are reconnected squeeze terminals end gently to ensure a good connection. This is a great company to deal with, I will be using them again. Thanks and good luck!!!
Was this helpful?
Thank you for voting!
Cooling fan runs fault code displayed
2 of 2 people found this instruction helpful.
  • FRANK from CLARENCE CTR, NY
  • Easy
  • 30 - 60 mins
  • Screw drivers
Removed the two screws holding the sensor to the rear oven wall. pulled out sensor wire. It was caught on other wires behind the oven. removed the three screws holding the 8" inspection plate in the center of the rear panel. Carefully move the insulation and reach in to grasp the back end of the sensor wire. Once free from the snag it eas ily pulls out with the sensor just as stated in the video. using the appropriate adaptor it was easy to re-asseble and and attach to the oven wall. Replace the rear panel with the three screws and it was done
Was this helpful?
Thank you for voting!
After cleaning, F1-1 error flashed and neither oven worked
3 of 5 people found this instruction helpful.
  • Georgene from Rock City, IL
  • Easy
  • 15 - 30 mins
  • Screw drivers
First I called a repairman and left a message. That was 3 weeks ago. So, I 'googled' the error message and determined what part I thought I needed. Ordered the part on Wednesday evening and it was there when I got home from work on Friday. I unpacked the part, got a phillips screwdriver and then watched the repair video on your websit e. About 20 minutes later I pushed my stove back in place and the flashing said 'set time'. Then I checked both ovens, and have since used both, and everything works!!
Was this helpful?
Thank you for voting!
Broil element burst
2 of 2 people found this instruction helpful.
  • Ronald from WEST COLUMBIA, SC
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Drop in range was in excellent condition until element burst and was getting ready to purchase another range and then I was looking to replace the element and found part select and they were great from the order process and shipping was fast and the whole process was 5 STARS. As far as me doing the repair I watched the video and it was s imple for even me. I also replaced the bake element at the same time. Once again I highly recommend Part Select and they are second to none.
Was this helpful?
Thank you for voting!
Bake element eroded
2 of 2 people found this instruction helpful.
  • Alison from NORTH EASTON, MA
  • A Bit Difficult
  • 1- 2 hours
  • Pliers, Screw drivers, Socket set
Everything was straightforward other than the tabs that the screws go through before going into the back of the oven were the wrong size and the predrilled holes were not in the right location. Had to trim the metal tabs and redrill the screw holes.
Was this helpful?
Thank you for voting!
Maytag range had "F3" code display, oven would not work.
2 of 2 people found this instruction helpful.
  • phillip from Farmington, NM
  • Difficult
  • More than 2 hours
  • Nutdriver, Screw drivers
Oven sensor replacement was easy. Thermistor was installed in less than 15 minutes. After installation STILL had "F3" error message. Harness was ok, "Clock" or ECU needed to be replaced. "Computer" is obsolete, no spares available, some companies will rebuilt for $400+. Since the stove was going to the landfill I had nothing to lose by taking the "Clock" apart. It has one chip that is probably the power supply and control chip, another chip is an EEPROM with 128 bytes of storage and the last is a darlington chip that controls the relays. Cleaned up everything that looked like it needed cleaning with alcohol. When I reassembled the unit the pins for the thermistor harness felt loose, so I took it apart, again, and found cold solder joints on all four pins. It must have been there all along but plugging and unplugging the harness finally broke out the solder so I could see it. Soldered the pins back in and now it all works. It's worth a try if you're getting the "F3" message. If the relays on your stove aren't working it would be a good idea to replace the darlington chip. Good luck.
Was this helpful?
Thank you for voting!
No temperature control
2 of 3 people found this instruction helpful.
  • Max from Houston, TX
  • Easy
  • 30 - 60 mins
  • Screw drivers
Turned off breakers to oven. Removed two screws that held oven in cabinet. Removed oven door by opening slightly and pulling up on door. Pulled oven out 1/3 of way. Took out four screws on top of control panel. Took oven light switch off by unscrewing holding ring. Removed temp knob on right by pulling. Removed start / stop knob same way. Removed glass straight out. Removed four screws that held elecrtonic clock conrtol board. Unpluged three wire plug from right side and the nine wire plug from the left side. Worked board out at and angle. Went backwards to connect and replace board, screws and door.Slid oven back in and tested oven after turning breakers back on, worked like new.
Was this helpful?
Thank you for voting!
Frayed and exposed receptical wires in cartridge
2 of 3 people found this instruction helpful.
  • Richard C from San Jose, CA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
* Do not lose the supplied CERAMIC electric connecting nuts; they will not fry in the heat.

* Unplug the heating elements from the old receptacles, and remove any rings; unplug the cartridge by lifting up the back side and pulling gently toward the back of the stovetop.

* Unscrew the cartridge top from the cartridg e base (about 12 screws) and the recepticals, and cut the old wire close to the old receptacle.

* If you have a spare magnetic thingy around, use it to hold the screws and not lose them.

* Screw in the new receptacles, route the newer wiring from the receptacles (use as much of the new wire as possible), back toward the wiring block on the cartridge plug.

* Recut the old wiring to accomodate the length of the new wiring, but leave at least 2-3" from the wiring block, if possible. Re-connect them using only the supplied CERAMIC electric nuts.

* The CERAMIC nuts allayed my fears about the effect of heat on a plastic nut; ceramic is designed for high-heat environments.

* Reverse the disassembly steps to reassemble and reinstall the cartridge.
Was this helpful?
Thank you for voting!
I needed a broiler pan
4 of 9 people found this instruction helpful.
  • Rhoda P. from Secaucus, NJ
  • Really Easy
  • Less than 15 mins
I took the broiler pan out of the shipping container and put it in the oven.
Was this helpful?
Thank you for voting!
Oven Temperature was 50 degrees low
2 of 3 people found this instruction helpful.
  • Eugene from Clinton, IA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Took screws out of the back on the side the sensor was on, unplugged it & took out the two screws on the inside of the oven to release the sensor. Put new sensor in place with the two screws & used one of the adapters to plug in the new sensor. Put screws back in the back panel & turned on the oven which unfortunately is still 50 degrees low. Need a new clock with computer which is out of stock & unavailable. I was an electrician for 25 years so didn't experience any problems. It was a cheap thing to try.
Was this helpful?
Thank you for voting!
Lower element out-oven wouldn't heat
1 person found this instruction helpful.
  • PATSY from HALLWOOD, VA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
I removed the two screws at the rear of the oven and pulled out the existing element, plugged in the new element, pushing it back in place and mounted the screws back in the bracket. I then made the "Tim the Tool Man" grunt noises feeling very proud that I am now officially a Handy Woman!
Was this helpful?
Thank you for voting!
Oven wouldn't heat
1 person found this instruction helpful.
  • Jonathan from Havertown, PA
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Easiest repair ever.

#1 - Turn off power (or you will get electricutued).
#2 - Unscrew back of heating elements
#3 - Disconnect wires (may need pliers)
#4 - Attach new heating element
#5 - Put in screws

Everything took 15 mintes max.
Was this helpful?
Thank you for voting!
No Bake, only Broil
1 person found this instruction helpful.
  • Edward from Adamstown, MD
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
POWER OFF! Unplugged oven from wall.

(Note: I found it easier to disconnect the wires from the element by removing the rear cover. Fumbling around inside the oven was getting me nowhere.)

Removed rear cover.
Disconnected old element.
Unscrewed the old element from inside the oven, removed, and installed t he new element. Screwed the new element in place.
Reconnected wires in back, installed the back cover.
Connected power.
Tested. Good as new.
Was this helpful?
Thank you for voting!
oven didn't heat up
1 person found this instruction helpful.
  • robert from merrimack, NH
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
removed the old element by taking out two screws then removed the two wires. pulled out the old element , put the new one in . connected the wires and screwed it in. Done.
Was this helpful?
Thank you for voting!
bake element disintegrated!
1 person found this instruction helpful.
  • Susan from Grand Ledge, MI
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Seems every 5 years this bake element totally disintegrates, so we,re experienced! Pull the stove out and remove the back, remove the 2 screws that hold the element(now in 5 pieces), diconnect and discard. Place new element in and connect, replace the 2 screws holding the element in place. Replace stove back. Easy
Was this helpful?
Thank you for voting!
All Instructions for the 3563
76 - 90 of 421