3524SRW Magic Chef Range - Instructions

turned off power removed old element .connected new element reinstalled works fine .part fit was correct part first time something rare in this day and age.

I shut the breaker off at the main power box.
In the oven, I loosened two screws to remove the old element (parts now, after the burn-out). I pulled the old element out of the back wall of the oven to expose the wire connections. I detached the simple sliding wire connectors. Done with removal. I waited for the new element to arri ... Read more ve (one week). Installed easily. Turned on the breaker and baked a few potatoes. Very simple.

Disconnected power plug,had to clean behind oven! , then...... removed 2 screws that held element in place, pulled element out about 3 inches disconnected 2 wires, removed old element, slide in new one, connected 2 wires, slide coil in carefully, and replaced 2 screws, replaced power plug checked operation, (worked fine) slide oven back i ... Read more nto place....wife was happy.

This is the second time I have replaced the bake element. It looks like 8 years is about as long as they last under normal use. The repair was simple; remove 2 screws, pull the bake element out, disconnect the wire connected to each end of the bake element, then reverse the process to reinstall.

Power off by unplugging appliance!
Remove the old element by removing one screw from each of the old element anchoring tabs.
Pull element away from back of oven approx. 3 inches to expose spade lug electrical connectors.
With the pliers, gently seperate the spade connector from the element connecting tab.
Remove old el ... Read more ement.
Install new element in reverse order.
Plug appliance in, set oven to warm/low heat to test and burn off any metal preserveative from elemnt surface.
Check operation by allowing to heat for < 30 seconds. Oven element should start to warm and can be confirmed by breifly placing hand a few inches away from element to detect heat.
Turn oven off if satisfactory. Reset time on oven clock. Finis!!!!

unscrew 2 screws, pull 2 connectors off, put in new part in reverse order - easy fix.

1. Turned off electricity to oven.
2. Unscrewed old oven element. Found it had burned through
on the underside.
3. Inserted & screwed in new oven element.

35 year old oven good to go.

Replaced the element.

This was a snap. It took me longer to find the right part number than it did to make the repair. After securing power to the oven, I removed the racks. I then unscrewed the element supports and pulled the element out slightly to expose the connectors. Using a pliers I removed the connector from each side of the element. At this point, I s ... Read more hould have placed a piece of electrical tape to prevent the connector leads from slipping back into the body of the oven. Instead, I fished them out with a tweezer, and slid the connectors back onto each side of the element. I then screwed in the elements supports, replaced the oven racks, and restored the power. It literally took less than 10 minutes.

Super simple. My husband ordered the part. It arrived in 3 days. The old element plugs right into cables on both sides of the back of the oven and are secured to the rear wall with screws. I unscrewed the plates, detached the wires on each side and slid the new ones in place. It was that easy and took me about 10 minutes.

Removed old element (two screws) unclipped two wires. Clipped the two wires to the new element (one at each end), reinserted new element, replaced the two screws. Done. Oh, flipped the circuit breaker back on:-)

unscrewed the old baking element, took the yellow wire off, and put the yellow wire onto the new baking element and screwed it back onto the oven. Took less than 15 minutes.

Simple repair.Just make sure you measure the length of element from back wall to plug in,width,and width of holes in back of oven.Simple repair with correct measurements.Pluged it in replaced screws plugged power back to unit , worked like a charm....Thank You!!!

Removed back of stove (6 screws), puled clips loose. Two screws inside oven, pulled out old element. slid new one in, replaced screws, slid on clips replaced back panel. Don't forget to unplug the stove frist.

Took out 2 screws pulled off the 2 female connectors. put the conectors on the new element and put the screws in. It took less than 10 minutes