345R - Parts

Maintain proper drive performance with this traction idler spring, designed to keep consistent tension on the drive belt for smooth and reliable operation. Built from durable metal, it helps ensure proper engagement of the ground drive system while reducing the risk of belt slipping during use. Engineered for dependable performance, this ...Read morecomponent supports efficient power transfer and helps keep your equipment operating smoothly in demanding conditions.

This check valve, also known as a one-way valve, is a genuine OEM part that regulates the flow of fuel/oil in the equipment engine to prevent it from flowing backwards. It is made of plastic and designed for use in a variety of lawn and garden power equipment. If the valve is jammed, worn down, or contaminated with dirt and debris, it wil...Read morel be unable to open and close properly, thus restricting the flow of fuel and compromising the engine combustion process. You will likely notice fuel leaks around the carburetor, engine stalling, hard starting, and overall lower performance from your equipment. To remove the faulty valve, carefully disconnect any hoses or fasteners connected to it. Place the new valve in position and secure it appropriately.

This authentic OEM rim sprocket in your chainsaw transfers power from the engine to the cutting chain. It is typically located at the center of the clutch drum, situated at the end of the engine crankshaft. By engaging with the chain drive links, it enables the chain to rotate and cut through materials as the engine turns. You will notice...Read more that if the rim sprocket is broken that the chain slips, does not engage, or rotates unevenly. It may also reveal signs of wear such as worn-out teeth. Failure to replace a broken rim sprocket can result in reduced cutting power, chain damage, and increased strain on the engine. To remove the rim sprocket, first, loosen the chain tension by adjusting the tensioning screw or knob. Then, remove the guide bar by loosening the nuts or clips on the side cover and sliding the guide bar off the saw. Use a screwdriver or appropriate tool to remove the screws or fasteners securing the clutch cover. With the clutch cover removed, you can access the clutch drum. Hold the drum in place and turn the retaining bolt counterclockwise to loosen it. Carefully slide off the clutch drum. This replacement part is sold individually.

Primarily used in chainsaws, this Starter Rope is an exact replacement part for hundreds of models. It is white and sold individually, not as part of a kit or assembly. The Starter Rope will need to be replaced once you notice signs of it fraying, wearing, or it breaks off. Customers rate this repair as Easy.

This is a genuine OEM part from Husqvarna. The brake spring is compatible with many snowblower machines. This metal spring is hooked from the frame assembly to the idler pulley, providing tension to the snowblower brake. The brake spring is sold individually. For the repair, you will need a screwdriver, adjustable wrench and a pair of pliers.

This M8 flange nut secures the guide bar and chain assembly in place, ensuring proper alignment and safe operation of your equipment. Designed with an integrated flange and anti-slip teeth to resist loosening from vibration, it provides a reliable, secure hold during heavy use. Made from durable, corrosion-resistant steel with an M8 threa...Read mored and 1.25?mm pitch, replacing a worn or missing nut helps maintain stability and dependable performance.

The flange bearing goes between the pulley flange impeller and the impeller assembly. This part is an OEM from Husqvarna, Poulan, and Jonsered for snowblowers. It is made of metal and will need to be replaced if it breaks. This high-quality part is priced individually and may require a socket set during installation.

This manufacturer certified 1/4 Hex Nut can be installed using a wrench or socket and is used to secure parts in place and spead the load. If the part being secured seems loose, check this nut and replace it if broken or missing. Refer to your make, model and diagrams to ensure this is the right part for you.

This stop button is a safety feature used in various types of lawn and garden equipment. It is a genuine OEM replacement part which is responsible for quickly shutting off the engine in case of an emergency or when it is no longer in use. The stop button is fitted into the handle controls for easy access. If the stop button becomes damage...Read mored or dislodged from its position, you will not be able to stop the equipment in an emergency. Therefore, it is important to replace the faulty stop button promptly to ensure that this emergency measure remains available, and avoid injury to the operator. Before beginning the repair, ensure that the equipment is turned off. Disconnect the stop button wires and detach the old stop button from the handle controls. Plug the new stop button in in place and reconnect the wires. If your equipment has fasteners with hex sockets, you will need to use a hex key/Allen wrench to remove and install the stop button. Ensure that the button is fitted securely before attempting to use your equipment again.

This screw is an authentic OEM part which made for Husqvarna chainsaws. It is designed for multiple uses based on your tool. Please refer to diagrams for correct location and applied use of this screw. It includes one (1) metal screw per order. This is a hex head item so you would need a hex key/allen wrench to install or remove it.

This is a genuine OEM sourced replacement part used with Poulan hedge trimmers. A spark plug delivers electric current from an ignition system to an internal combustion engine. After time spark plugs will become dirty or fouled. It is a good idea to replace the spark plug once this happens. This item is sold individually. You should gap y...Read moreour spark plug according to the owners manual of the outdoor product you have. You would need a spark plug wrench or a socket wrench to install this component.

The rubber wheel ring attaches to the wheel hub. This part is an OEM from Husqvarna, Poulan, and Jonsered for use in snowblowers. It is sold individually. A socket set and a wrench set might be required during the replacement of this part. It may become broken and will need to be replaced.