345R - Overview

Genuine Husqvarna replacement part, this part is sold individually. The 503939601 Air Purge does just what the part name says. It purges the air out of the carburetor. Then it forces fuel from the fuel tank and fuel line in to the carburetor.

This OEM fuel line, or hose, is a 4-inch, clear, plastic tube which is sold individually. It is rated as "Easy" to install. This part connects to the purge assembly and delivers fuel to the carburetor or is used as a return line to the tank. A broken hose will leak, and should be replaced. Refer to your make, model and diagrams to check if this part is right for you.

The air cleaner knob, just over 1 inch in diameter, is black in color and made of plastic. It is sold individually, and its function is to tighten the air cleaner cover down on various lawn and garden equipment. This knob can become worn over time, which will cause the air filter cover not to stay in place. Most of our customers find this to be an easy repair. It does not require any special tools.

Used to seal the fuel tank to prevent leaks and allow the fuel line to enter through it, this Fuel Tank Bushing is sourced directly from the manufacturer. It is made of black rubber, is not part of a kit or assembly, and is sold individually. This part will wear through regular use and should be replaced if you notice signs of damage or...Read more wear. When it malfunctions, you will see fuel leaking from the bushing. You will need a screwdriver and pliers to complete this repair. Customers rate this repair as Easy.

This chute base, also known as a discharge chute base, is sourced from the original manufacturer for use with snowblowers. It is found at the end of the discharge chute which is responsible for directing the discharge of snow, or other materials that are being thrown by the equipment. The chute base is found at the end of the discharge ch...Read moreute where it acts as a connection point between the chute and the auger housing. The chute base aids in directing the discharge to a specific place, as well as controlling how far the discharge is thrown. If the chute base becomes damaged, cracked, or worn out, it will need to be replaced. A faulty chute base will result in snow being thrown haphazardly, not being thrown far enough or not thrown at all. It can also create blockages in the equipment, leading to potentially expensive repairs. Remove the fasteners that secure the base to the equipment and pull off the old chute base. Align the new chute with the mounting bracket and secure it with the fasteners.

Compatible with over 150 models of lawn equipment, this Spark Plug has been sourced directly from the original manufacturer. It is sold individually, made of metal and ceramic components, and is not part of a kit or assembly. The spark plug is used to ignite the air-fuel mixture inside the combustion chamber. You may need to replace the...Read more Spark Plug if your 1 cylinder engine won't start, or if your more-than-1 cylinder engine runs rough. Spark Plugs will wear over time and should be inspected regularly. Customers rate this repair as Easy.

This fuel tank bushing grommet creates a tight seal where the fuel line enters the tank, helping prevent leaks and keep air and debris out of the fuel system. Made from durable, fuel-resistant rubber, it supports reliable engine performance and consistent fuel flow. Replacing a worn or damaged grommet can help eliminate leaks and restore proper operation.

This O-ring is a genuine OEM replacement part designed for use in a variety of power tools. It is a rubber seal used to prevent pressure loss, as well as oil, fuel, and air leakage from the fuel hose. It can be found on either end of the hose. You will need to replace this ring if it has lost elasticity, or if it is cracked or deformed. T...Read morehe O-ring can fail due to age, exposure to heat and chemicals, pressure buildup, or poor installation. A faulty ring will result in leakages, pressure loss, and decreased equipment performance. Carefully pry the old O-ring off the hose. Remove any dirt or debris in the area and lubricate the new ring before placing it in position. Apply light pressure to the ring until it is secure and sitting snugly. Note that your equipment may have several O-rings, therefore, inspect all of them as each ring is sold individually.

This 25mm blade nut is a fastener that secures the blade to the spindle or shaft of your lawn equipment. It is located at the center of the blade. Signs of a broken blade nut include looseness, stripping, cracks, or excessive wear. Failing to replace a broken blade nut can result in a loose or dislodged blade during operation. To unthread...Read more the blade nut on your machine, use a wrench or socket to loosen it. This OEM component is sold individually. To ensure you have the correct number of blade nuts for your machine, refer to the user guide as your equipment may require multiple blade nuts. Consider replacing all of the nuts in one go as they wear out at similar rates.

This manufacturer approved replacement part is designed for snow blowers/throwers. Skid shoe/plate allows you to avoid damage and keep smooth control over cracks, gravel, and other uneven surfaces. It is made out of metal and it is sold individually. Please note the right skid plate is sold separately. It is advised to replace both skid ...Read moreplates at the same time. To complete this repair you will need a wrench. • First remove bolts holding old skid plate • Remove old plate and insert new skid plate • Level snow blower and adjust skid plates to desired height • Tighten skid plate bolts

The deflector spring is made of metal and attaches to the deflector assembly. This spring is available as an individual replacement part. It will need replacement if it becomes stretched or broken. It is used in Husqvarna, Poulan, and Jonsered snowblowers and is an OEM from the manufacturer.

This shear bolt secures the snowblower auger to the drive shaft while acting as a built-in safety feature. Designed to break under excessive force, it helps protect the gearbox and engine from damage if the auger hits a hard object. Replacing a broken or missing bolt restores proper auger operation and ensures reliable, safe performance.