3448 Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Very old burner grates & drip pans, need replacement.
15 of 23 people
found this instruction helpful.
-
Mariano from Torrance, CA
- Really Easy
- Less than 15 mins
Took out the old & easily replace it with the new set. No tools required.
Other Parts Used:
Was this helpful?
Thank you for voting!
oven would not maintain temp
12 of 14 people
found this instruction helpful.
-
doyle from demorest, GA
- Really Easy
- Less than 15 mins
-
Screw drivers
. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) pushed wires back in and secured sensor
Was this helpful?
Thank you for voting!
burner head was rusted out. ordered 1 to see if part was correct. ordered 4 more to finish job.
13 of 17 people
found this instruction helpful.
-
Robert from Somerville, TN
- Really Easy
- Less than 15 mins
unscrewed old burner head ;disconnected 2 wires; repaced with new burner head and replaced wires. Unfortunately, before we really needed to replace the other burner heads, the cooktop itself developed a gas leak. We decided to replace the whole thing, and therefore would like to return the unboxed, unused 4 remaining burner heads.
Was this helpful?
Thank you for voting!
Oven door wouldn't close or open all the way
14 of 20 people
found this instruction helpful.
-
Michael from St. Cloud, MN
- Easy
- 30 - 60 mins
-
Screw drivers
1st removed the sealed burners
2nd removed stove top
3rd removed oven door
4th removed left and right side pannels to access door hinges
5th removed left and right hinges
6th installed new left and right hinges
then re-installed other components in reverse order.
The oven door now opens and closes proper ... Read more ly, the heat stays in the oven!!
2nd removed stove top
3rd removed oven door
4th removed left and right side pannels to access door hinges
5th removed left and right hinges
6th installed new left and right hinges
then re-installed other components in reverse order.
The oven door now opens and closes proper ... Read more ly, the heat stays in the oven!!
Read less
Was this helpful?
Thank you for voting!
Oven wouldn't heat up / ignitor was bad
11 of 12 people
found this instruction helpful.
-
Timothy from Sandusky, OH
- Easy
- 15 - 30 mins
-
Nutdriver
Our original oven ignitor went bad. The gas supply won't even open, unless the oven senses the proper voltage / resistance across the ignitor, so that gas won't be flowing without ignition.
PartSelect was very good about providing me with the proper part, after I got the part number from their schematics and wiring diagrams, ... Read more on the website. The first replacement part actually arrived, broken, from shipping, but when I called them, they immediately reprocessed the order, and sent me a new ignitor, to arrive the following day. I was very satisfied with their professionalism, as I've been in the past with them, as well.
On to the actual repair:
I removed the broiler drawer from the drawer slides, reached under the main oven chamber, unscrewed the two screws holding the ignitor in place, and cut / disconnected the two wires supplying the power to it.
I then put the new ignitor in place and screwed it back to the mount, used the wire nuts that came with the new ignitor to reconnect / splice the wires, and put the broiler drawer back in place.
Oven fired right up!
Entire process took less than 35 minutes. (Likely would've taken a bit longer, but this is the second replacement for the ignitor, since we've owned this oven, so I already had a good idea how to do it. (The first replacement for this particular part was NOT from PartSelect, so we're hopeful this one lasts a while longer than the previous one.)
Thanks, PartSelect!
PartSelect was very good about providing me with the proper part, after I got the part number from their schematics and wiring diagrams, ... Read more on the website. The first replacement part actually arrived, broken, from shipping, but when I called them, they immediately reprocessed the order, and sent me a new ignitor, to arrive the following day. I was very satisfied with their professionalism, as I've been in the past with them, as well.
On to the actual repair:
I removed the broiler drawer from the drawer slides, reached under the main oven chamber, unscrewed the two screws holding the ignitor in place, and cut / disconnected the two wires supplying the power to it.
I then put the new ignitor in place and screwed it back to the mount, used the wire nuts that came with the new ignitor to reconnect / splice the wires, and put the broiler drawer back in place.
Oven fired right up!
Entire process took less than 35 minutes. (Likely would've taken a bit longer, but this is the second replacement for the ignitor, since we've owned this oven, so I already had a good idea how to do it. (The first replacement for this particular part was NOT from PartSelect, so we're hopeful this one lasts a while longer than the previous one.)
Thanks, PartSelect!
Read less
Was this helpful?
Thank you for voting!
Spring on hinge broke. Door wont close totally
12 of 15 people
found this instruction helpful.
-
Thomas from Baton Rouge, LA
- Very Difficult
- More than 2 hours
-
Pliers, Screw drivers, Socket set
Using the description on the first DIY, I did as told. All went well until the part about removing the panel to access the hinge. There isn't a "panel" on the side of this particular model of Magic Chef stove. You have to remove the entire side of the stove, and then, there's another panel inside of this one. That too has to come off. On
... Read more
ce off, you're into the insulation surrounding the oven. Ain't pretty, I'll assure you. Then, the replacement hinge has holes in it for the mounting screws. The holes aren't threaded, and you have to replace the screws that come with the hinge with self-tapping screws. Either that, or thread the holes with a tap. Thank goodness my wife loves the stove, or it may have just gone out the door. This is not one of Magic Chefs better ideas. Either that, or they didn't plan on having to replace the hinge before the stove wore out.
Read less
Was this helpful?
Thank you for voting!
oven won't stay light
10 of 10 people
found this instruction helpful.
-
Shannon from Lake Park, IA
- Easy
- 15 - 30 mins
-
Screw drivers
removed racks, bottom plate. removed screws with a little bit of help from cooking spray. Unclipped old ignitor clipped in new ignitor, used old screws, and inserted insulation replaced racks, bottom shelf. Turn on oven and worked, been using it for about a week now. PS. ordered on monday morning arrived wednesday afternoon.
Was this helpful?
Thank you for voting!
Oven Racks needed to be replaced.
11 of 14 people
found this instruction helpful.
-
Peter from Chicago, IL
- Really Easy
- Less than 15 mins
Slide out the old; slide in the new!
Was this helpful?
Thank you for voting!
Oven would not light
9 of 10 people
found this instruction helpful.
-
Matt from Verona, WI
- Easy
- 15 - 30 mins
-
Screw drivers
Make sure you unplug the oven before you begin. I removed the old igniter. The top wire on the igniter goes to the back of the oven and plugs into a flat blade type connector. Instead of using the twist wire nut I used a flat connector because it was easier to put on and is foolproof. Make sure you cut the plastic insulation off the c
... Read more
onnector so it does not melt when the oven is in use. I used a wire nut on the other wire and that was it. Very simple and the oven works great again.
Read less
Was this helpful?
Thank you for voting!
tHE ORIGINAL MODULE DIED AFTER 21 YEARS OF SERVICE
11 of 16 people
found this instruction helpful.
-
Jose from El Paso, TX
- Really Easy
- 15 - 30 mins
-
Screw drivers
First had to move the stove out of its "nest", take the side cover off, remove 1 screw and loosen the other , take the old module out and reverse the operation. That simple.
Part was supplied 1 day before promised date, awesome. Part fitted exactly as the OEM part, works like a charm, everyone happy.
Part was supplied 1 day before promised date, awesome. Part fitted exactly as the OEM part, works like a charm, everyone happy.
Was this helpful?
Thank you for voting!
The oven would not fire up.
12 of 19 people
found this instruction helpful.
-
edward from smithtown, NY
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
I searched the item I needed and followed a link to PartSelect.com. I paid a little extra for shipping and literally recieved the part in two days. The part was an absolute perfect fit and my wife and myself have never been happier. Home cooked meals again thanks to the folks at PartSelect.com. It couldn't have been an easier.
Was this helpful?
Thank you for voting!
Cracked gas feed tubes
9 of 11 people
found this instruction helpful.
-
Jeff from Union City, CA
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
CAUTION: DO NOT LIFT RANGE TOP AS IT WILL CRIMP YOUR GAS FEED TUBES!!!
Remove grates and drip covers. Twist each burner counter clockwise and lift off. Remove ground wire and ignitor wire from each burner. Remove screws that holds the Orifice/Tube assy to the range top (one where each burner was) You might have to remove the or ... Read more ange rubber flanges if they didn't stay on the burners to see the screws.
Now lift (or remove) your range top to get access to the tube assy. Take a wrench and remove each gas tube nut (2 for each assy) and remove the old assy.
Drop each new Tube assy in and reverse the procedure.
Remove grates and drip covers. Twist each burner counter clockwise and lift off. Remove ground wire and ignitor wire from each burner. Remove screws that holds the Orifice/Tube assy to the range top (one where each burner was) You might have to remove the or ... Read more ange rubber flanges if they didn't stay on the burners to see the screws.
Now lift (or remove) your range top to get access to the tube assy. Take a wrench and remove each gas tube nut (2 for each assy) and remove the old assy.
Drop each new Tube assy in and reverse the procedure.
Read less
Was this helpful?
Thank you for voting!
F-3 error code
8 of 8 people
found this instruction helpful.
-
Mark from Lake Orion, MI
- Easy
- 15 - 30 mins
-
Screw drivers
I removed the two screws that attach the sensor to the oven wall. Then removed to more screws in the back of the oven and took off the rear cover, diconnected the sensor connector and installed the new sensor.
Was this helpful?
Thank you for voting!
inner glass busted
9 of 11 people
found this instruction helpful.
-
robert from orange, CA
- Easy
- 15 - 30 mins
-
Screw drivers
I removed door by opening it to first stop and lifted it up off the hinge's. I removed all screws that held the inner panel to the outer panel and handle. Removed inner panel from outer panel, then glass and insulation, replaced glass and insulation and panel.
Replaced screws and handle,pulled hinge's out to first stop and sli ... Read more d door down on hinge's. This took about 20min. to do, most anybody handy with a screwdriver can do it.
PS: shipping was fast and price was great.
Thanks Bob G.
Replaced screws and handle,pulled hinge's out to first stop and sli ... Read more d door down on hinge's. This took about 20min. to do, most anybody handy with a screwdriver can do it.
PS: shipping was fast and price was great.
Thanks Bob G.
Read less
Was this helpful?
Thank you for voting!
original drip pans were rusting on the undersides
9 of 11 people
found this instruction helpful.
-
Sandra from Okeene, OK
- Really Easy
- Less than 15 mins
Just to point out the pans were delivered within a few days which was very quick. I just dropped them in. They fit perfect. Thank You for no stress.
Was this helpful?
Thank you for voting!