EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3448 Range - Instructions

All Instructions for the 3448
16 - 30 of 690

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
No spark at top burners, first one then eventually all 4.
35 of 41 people found this instruction helpful.
  • jonathan from Bryson City, NC
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Most of the repair time was spent researching the problem online, locating the spark module inside the range, and selecting the part online. Installation was easy. Key troubleshooting info for me was, if there is no clicking, the spark unit is probably worn-out. I traced the ignition wires from the burners down to the spark module, locate d inside a 2x3" metal housing next to the bottom drawer. I removed 2 screws and out it came. The replacement unit pictured on the PartSelect site was not identical to the original but had the same number of contacts. I ordered the part and it arrived a few days later. The old connectors slipped easily onto the new pins, and I screwed the new unit into the range using the new metal housing. All 4 burners now spark up quickly, and we saved at least $100 on a service call. It was well worth the time and effort -- thanks!
Was this helpful?
Thank you for voting!
The oven took too long to ignite (3-5 minutes), or didn't ignite at all. Same description as others on this site.
33 of 35 people found this instruction helpful.
  • Glenn from Jenison, MI
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Turned off the breaker to the oven. Took out the racks and oven floor. Took out the steel deflector that sits on top of the oven burner itself (one bolt/washer). Removed the two bolts holding the igniter. Pulled the old igniter around the other side of the burner to be able to better access the wires. There was a woven sleeve around the e nds of the wires, pulled those down the wire to expose the connection. There was an inline connector about 2-3 inches from the igniter, and normal wire after that. I cut the wires where that connection was made and stripped 3/8 inch off the cut wires. Then I cut the wires of the new igniter to the same length as what remained on the old igniter, stripped 3/8 inch off of those, paired them up and used the ceramic wire nuts that came with the new part to make the new connections. Put it all back together, and fired it up. It works wonderfully!
Was this helpful?
Thank you for voting!
Oven would not light
29 of 30 people found this instruction helpful.
  • Richard from Austin, TX
  • Easy
  • 1- 2 hours
  • Pliers, Screw drivers
This oven was located in a rental house I own.

I first removed the metal plate that covers the burners at the bottom of the oven. No tools required for this step.

Next I turned the oven to 300 degrees, waited 30 seconds and noticed that the igniter was glowing brightly, but the burners did not light.

I nex t turned the oven controls off, pulled the plug, and set to work removing the 2 screws holding a plate to the back oven wall and the 2 screws holding the igniter to the burner. These last 2 screws had corrosion on them and I needed to use vise-grips to get a firm hold on them. During reassembly these screws no longer held firmly because the hole they threaded into was enlarged during disassembly.

With the screws loose I pulled the igniter and fished the wires connected to it through the opening until I saw the connector. I then pulled the stove out of its opening and saw that there was a easily removable metal cover over the wires, and I took it off.

The new igniter came with an incompatible plug, so I cut off the connector on the stove wiring and on the new igniter and used wire nuts to make the new connections. I kept the orientation of the old and new plugs the same way in case the wiring mattered, but that was just being safe. I don't know if the igniter cares which of its wires go to which wire on the stove.

I reinstalled the screws holding the igniter, and shoved short sections of the supplied wiring into the screw holes so that the screws would hold more tightly. I shoved the supplied insulation into the opening that the wires passed through, and reattached the cover at the back of the stove.

I shoved the stove back into its opening, turned the oven on and it lit within 15 seconds.

I was very happy with the result, and the product I ordered arrived on time, well packaged and I'm a very happy customer.
Was this helpful?
Thank you for voting!
Burner wouldn't start
35 of 48 people found this instruction helpful.
  • Yury from Brooklyn, NY
  • Really Easy
  • Less than 15 mins
Make a quarter turn counterclockwise, disengage a burner head, disconnect 2 wires, connect to a new head, install turn clockwise.

That's it!
Was this helpful?
Thank you for voting!
Oven would not heat- Beeped nonstop and flashed F3
29 of 33 people found this instruction helpful.
  • Erin from Greenwich, CT
  • Really Easy
  • Less than 15 mins
  • Screw drivers
First I removed two screws that hold the oven sensor in place. I then removed the screws that held the panel on the back of the oven. I simply unclipped the plastic adaptor and replaced the old sensor with the new one. I screwed the sensor back in and put the back panel on. turned the power back on to the oven and hit the bake button. Voi la!! The oven turned on and now it works like new!!!
Was this helpful?
Thank you for voting!
Oven wouldn't heat up : (
28 of 32 people found this instruction helpful.
  • Janet from Hampton, VA
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
It was amazingly easy! I am a woman who was a little afraid to deal with wires. But it was just so super easy! And, I saved a bundle by doing it myself! Here's how I did it:
(1) UNPLUGGED OVEN FROM WALL!!!
(2) Remove floor of oven (1 screw)
(3) Remove large metal strip underneath oven floor (2 screws)
(4) R emoved oven igniter (2 screws)
(5) Marked top wire of old igniter before cutting
(6) Cut both wires close to old igniter
(7) Removed a little of the covering of the old wires to expose bare wire
(8) Matched up old top wire with new top wire & twisted both old wires to the new wires
(9) Replaced all screws and oven parts
Was this helpful?
Thank you for voting!
oven takes a long time to reach temp set point
23 of 25 people found this instruction helpful.
  • Scott from Brooklyn Park, MN
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
i need to replace the lower oven igniter about 2-3 years
unplug the oven
open the oven door half way then slide the door up
take out both racks
push the bottom pan away from you and lift up
one screw holds the igniter on
pull the wire out until you get to the electrical plug
disconnect
Was this helpful?
Thank you for voting!
Oven would not ignite
24 of 31 people found this instruction helpful.
  • Bob from Crystal Lake, IL
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Step one - Diagnose. Used a clamp-on ammeter around the igniter lead to check if 3.6 amps or greater were present during ignition. Only about 2.5 amps were measured, indicating that the igniter was bad.

Step two - Ordered the part.

Installation - Removed the racks and bottom oven compartment cover plates, exposing the igniter/burner assembly. Removed the bottom drawer, cut the wires of the existing igniter (leaving plenty of wire left for the new one). Removed the igniter/burner assembly through the oven compartment. Removed the old igniter from the burner, installed the new one. Re-seated the igniter/burner assembly, routing the wires appropriately. Stripped the existing leads (cut in previous step), spliced the new leads in, soldered the connection (soldering is optional). Taped up the splices with electrician's tape. Turned on the oven to verify that the new igniter glowed and the burner lit. Turned off the oven and waited for the burner to cool. Replaced the bottom cover plates and rack.

Final step - Baked some bread.
Was this helpful?
Thank you for voting!
Kept getting F3 errors
21 of 23 people found this instruction helpful.
  • Daniel from Long Beach, CA
  • Easy
  • 15 - 30 mins
  • Screw drivers
My oven stopped working and the display read F3 error. I looked up the code and found that it was probably the thermostat sensor. I ordered the part from partselect.com and when it arrived I went to install it but I ran into a somewhat scary issue. I found that I had to pull my oven out of the wall in order to replace the sensor.

After a minor nervous breakdown, I decided to go for it and found that it was much easier than I had imagined. Changing the sensor involves taking out the two screws that hold the sensor in place (inside of the oven), pulling it out to the point you can reach the connector, plugging in the new sensor and screwing it back in place. However, if you have an oven like my model, you have to pull out the whole oven from the wall in order to reach the plug on the sensor. This sounds like a lot of trouble but for me it was very easy. The oven is held in place with screws around the front side. Most are easily accessed and you don't have to take out any critical/complicated pieces of the oven. My screw gun made short issue of the problem and I found that the oven was out of the wall within minutes. I could then easily unscrew a small back cover, change the sensor and then screw the oven back into the wall. Being very careful, the whole operation took about 20 minutes. I recommend that you get help from a friend just because the oven is bulky. It is not heavy, an average sized male can handle the weight but it’s easier with a friend. Also, be careful that the gas hose which feeds the oven is long enough (and not tangled) for you to move the oven out of its space. Obviously, be careful about gas leaks.
Was this helpful?
Thank you for voting!
oven burner would not come on.
20 of 20 people found this instruction helpful.
  • Theodore C. from Winsted, CT
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
I am a retired lp Gas service person so this was quite
simple for me. Replaced the oven Igniter. What amazed me I placed my order and had the Igniter less than 24 hours. thank you so much for the quick service.
Was this helpful?
Thank you for voting!
Oven would not light -- gas smell
22 of 27 people found this instruction helpful.
  • Mark from Rockwall, TX
  • A Bit Difficult
  • 1- 2 hours
  • Screw drivers, Socket set, Wrench (Adjustable)
Remove racks and pull out stove from wall. Remove back cover from stove. Unscrew and unplug sensor. Rethread new sensor wire through hole and plug in new sensor and rescrew plate that holds in place.

We had complications because of how the stove was installed, which delayed the "fix" time considerably.

Also instal led ignitor. It was determined that both were bad. Gas would come on but not light. When oven would light, it would not re-light periodically to keep the temperature up, causing gas smell. This added time to repair of an additional 1 hour, and required removal of bottom drawer.
Was this helpful?
Thank you for voting!
Long time to light, strong gas smell
18 of 18 people found this instruction helpful.
  • Kevin from DeRuyter, NY
  • Easy
  • 15 - 30 mins
  • Nutdriver
Unplug power, remove draw, marked and cut wires, unscrewed and removed old igniter, replaced and screwed new igniter into position, reconnected wires with supplied porcelin wire nuts, replace draw, plug in and tried...working great.
Was this helpful?
Thank you for voting!
igniter would light----gas valve would NOT open
21 of 28 people found this instruction helpful.
  • Robert from SALEM, IL
  • Easy
  • 30 - 60 mins
  • Screw drivers, Wrench (Adjustable)
SHUT OFF GAS
disconnect FLEX LINE from gas PIPE
remove GAS pipe from rear of stove
remove rear panel
remove pre-shaped gas lines to burners and oven / broiler
separate dual control valve from pressure regulator
disconnect wiring from dual control valve
REASSEMBLE in OPPOSITE order
turn on gas ... Read more />CHECK ALL FITTINGS FOR POSSIBLE LEAKS
Turn on each BURNER - making sure EACH one lites
turn on oven - making sure that the OVEN igniter lites the OVEN
set control on BROIL
turn on broiler - making sure that the BROILER
igniter lites the BROILER
Was this helpful?
Thank you for voting!
missing oven racks
20 of 25 people found this instruction helpful.
  • ALLAN from APACHE JUNCTION, AZ
  • Really Easy
  • Less than 15 mins
order pcs fit perfect.
Was this helpful?
Thank you for voting!
Burners would not ignite
19 of 23 people found this instruction helpful.
  • Craig from Sequim, WA
  • Easy
  • 15 - 30 mins
  • Screw drivers
Pulled the stove out from the wall. Removed the left side of the stove. Removed the wires from the old igniter. Modified four of the wire ends with the proper size spade connectors (supplied with the new part). Reinstalled the wires onto the new part. Tested the burners. Reinstalled the stove side. Moved the stove back into position.
Was this helpful?
Thank you for voting!
All Instructions for the 3448
16 - 30 of 690