EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3448 Range - Instructions

All Instructions for the 3448
61 - 75 of 690

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
When the oven was turned on, F2 and F4 came on. Oven wouldn't heat.
9 of 11 people found this instruction helpful.
  • Crystal from Scott City, MO
  • Really Easy
  • Less than 15 mins
  • Screw drivers
After reading some of the repair stories, I was hesitant about doing this task. It was really very simple, I just removed the screws from the back of the stove, and removed the old element. I then replaced it with the new one and replaced the back cover. This whole task from start to finish took 10 minutes. The oven heats perfectly now ju st like a new oven.
Was this helpful?
Thank you for voting!
Oven wouldn't ignite
8 of 8 people found this instruction helpful.
  • Treasure from High Point, NC
  • Really Easy
  • Less than 15 mins
  • Screw drivers
First I unpuged the Range. Then I removed all racks and bottom tray of oven.
The Ignitor is located at back of oven, paralelle to the gas bar. I removed the 2 screws holding the ignitor and unpluged the wires. Then I put on the new ignitor, perfect fit, replaced the 2 screws and pluged in the wires , then pluged in the range. I tur ned the oven on and it lit in about 10 seconds.
Thank you PartSelect for having such a wide range of range & oven parts . no one should have to pay a service tech. to fix most problems, as long as we have a GREAT SITE LIKE THIS ONE.
p.s. You guy also had one of the lowest prices , my part arrived ahead of schedule .
THANKS A LOT !
Was this helpful?
Thank you for voting!
Oven would not preheat and gave 'F1' error
9 of 11 people found this instruction helpful.
  • Joshua from Reno, NV
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Had to unplug unit, remove back of unit (6 screws), then unscrew oven sensor (2 screws), then unplugged old sensor, replaced it and put back of oven on...Moving the oven out and working in the tight space avaialble was the most difficult. Other than that, super easy job that probably saved me a lot of $$$...
Was this helpful?
Thank you for voting!
Oven would not heat but Broiler would
8 of 9 people found this instruction helpful.
  • Robert from Hudson, OH
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
Turn off the gas supply and unplug the power cord. Remove the screw on the back plate for the metal tab that covers the valve. Bend the tab up to expose the valve. Remove the gas line that feeds the broiler with an adjustable wrench. Remove the mounting screw for the valve. Loosen the valve inlet gas line fitting with an adjustable wr ench. Lift the valve out. Reverse the steps to install the new valve.
Was this helpful?
Thank you for voting!
oven would not light -igniter was on
9 of 12 people found this instruction helpful.
  • Tom from South Amboy, NJ
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers, Socket set
removed shelves and base, removed 2 screws that held igniter on, disconnected wires from gas valve removed protective cover in corner {1 screw}
disconnected plug, removed igniter. This igniter was easier to remove from front of stove on this model
Was this helpful?
Thank you for voting!
Original oven light lens had cracked and broken in two.
17 of 36 people found this instruction helpful.
  • Pat from Bucklin, KS
  • Really Easy
  • Less than 15 mins
I screwed the light lens into the socket and went beautifully. Better than the original. (I am a retired, 75 yr. old woman).
Was this helpful?
Thank you for voting!
Oven would not light
8 of 9 people found this instruction helpful.
  • Ronald from LONG BRANCH, NJ
  • Easy
  • More than 2 hours
  • Nutdriver, Screw drivers, Socket set
Working on an old oven is difficult. Please expect the unexpected. The years of heating and cooling play havoc with oven parts. The screws holding the Flat Style Oven Ignitor become stripped. It took extra time to remove them. I had to go to the hardware store to buy replacement screws. Once I removed the old parts and had replacement screws the job was very easy.
Was this helpful?
Thank you for voting!
burners rusted out on one side since the stove is 19 years old
8 of 10 people found this instruction helpful.
  • Elizabeth from Johnstown, PA
  • Really Easy
  • Less than 15 mins
Bought two to try out to see if they fit and worked-popped out the old ones and the new ones fit and worked like a new stove. Came back to this web site and bought the other two so all burners are now brand new without having to replace the stove.
Was this helpful?
Thank you for voting!
The oven would take forever to heat up, and sometimes not at all. Othertimes it would heat up, but not stay hot for the entire baking time.
7 of 7 people found this instruction helpful.
  • Jason from Los Angeles, CA
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
First, I unplugged the oven from the wall. I opened the bottom drawer of the oven to see where the igniter was mounted, which was directly under the bottom pan of the oven itself. I opened the main oven door and unscrewed the 2 screws that were holding the pan to the bottom of the oven. Then, I slid the pan back towards the the back of t he oven and it popped right out.

There were 2 hex screws that were holding the old igniter on, so I unscrewed them with my socket set. I made sure to pay attention to which wire was the top one and which one was the bottom one coming out the back of the igniter. I pulled off the wire nuts connecting the igniter wires to the wires of the oven. I striped the wires on the new igniter and re-attached them to the proper wires of the oven, using the included replacement ceramic wire nuts. I re-screwed the hex nuts in, mounting the new igniter to its proper place. I put the pan back and screwed the 2 screws back in to hold it in place.

Plugged it back in, turned it on, fired up within 20 seconds. Good as new.
Was this helpful?
Thank you for voting!
Inner Galls on door was craked
8 of 11 people found this instruction helpful.
  • Randall from Katy, TX
  • Easy
  • 15 - 30 mins
  • Screw drivers
Remove outer panel first, outer glass and handle come off as one piece. Be carefull to secure as last screws are removed. Remove inner silver panel. Remove broken glass and replace with new. Reaassemble. Around 10 Phillips head screws altogether. Much easier than I thought
Was this helpful?
Thank you for voting!
oven temperature not reaching setting/temp. up and down
7 of 8 people found this instruction helpful.
  • Ellen from Schenectady, NY
  • Easy
  • 15 - 30 mins
  • Screw drivers
Removed back of stove, removed screws from sensor inside oven, unplugged connector from back of stove, pulled sensor out through oven; installed new sensor, replaced back of stove. Set the oven to bake, waited for it to pre-heat; the oven thermometer showed that the same problem was occurring, the sensor replacement didn't work.
Was this helpful?
Thank you for voting!
Oven temperature lower then setpoint.
7 of 8 people found this instruction helpful.
  • Robert from Massapequa, NY
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
After shutting the main valve behind stove. Removed all shelves and rear cover from stove. Unplugged the plug to the sensor. Removed the two mounting screws and pulled the old sensor out. Installed new sensor and plugged it in again. After reinstalling the rear cover and shelves, replugged in power, openned the gas valve behind the stove and tested with soapy water to make sure there wasn't ant developed leaks. Turned on oven with a test thermometer in it. Monitored operation and now oven temperature is roughly 10 to 20 degrees to the setpoint.
Was this helpful?
Thank you for voting!
Oven floor panel was warped.
8 of 11 people found this instruction helpful.
  • Cindy from Colton, CA
  • Really Easy
  • Less than 15 mins
It was so easy, I pushed the panel towards the back and lifted the front up then lifted it right out. I am so glad that you had the part. I ordered it and when it got here, I just sliped it right in, perfect fit! Thank you so much! Cindy Brison
Was this helpful?
Thank you for voting!
the burner knobs broke off
10 of 17 people found this instruction helpful.
  • Belinda from Downey, CA
  • Really Easy
  • Less than 15 mins
I put the 2 burner knobs on and now I have 4 working burners....Thanks for the quick delivery....
Was this helpful?
Thank you for voting!
Oven light bulb went dark; it needed replacing
10 of 17 people found this instruction helpful.
  • Lise from CEDAR GROVE, NJ
  • Very Easy
  • Less than 15 mins
Twisted replacement bulb into place easily. Let there be light!
Was this helpful?
Thank you for voting!
All Instructions for the 3448
61 - 75 of 690