3187 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The problem was exactly what was described on your site.
2 of 2 people
found this instruction helpful.
-
William from FREELAND, MI
- Very Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I pretty much did the repair the same way the video described it. I first turned off the gas valve and disconnected the power. Then removed the two screws holding in the burner tube and removed it. Then I unplugged the old igniter. The screws were a bit corroded so I gave them a little spray of liquid wrench. They came right out them. Aft
... Read more
er removing them I replaced the igniter plugged it in. Then I put the wire through the hole in the wall of the oven. Replaced the insulation that was included in the kit. Replaced the burner tube on the venture. And reinstalled the screws. It was pretty cut and dry. The glow plug had the burner fired up in 15 seconds.
Read less
Was this helpful?
Thank you for voting!
Oven wouldn't heat
2 of 2 people
found this instruction helpful.
-
Tom from Greenville, NC
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
I researched the stories on Partsselect, and it looked like this would be a simple repair. Fortunately, it was more simple than I'd thought. We bought the house (and stove) used, and the ignitor apparently had been replaced before, because the part was an EXACT replacement for the old one. I simply unscrewed the two screws holding the ol
... Read more
d ignitor onto the bracket/burner, pulled the wiring from the back of the oven through the insulation, disconnected the snap connector, reattached the new one. Then I pushed the wiring back through the insulation and added some additional insulation (provided with the part), making sure all extra length was pushed into the insulation. Reattached with two screws using a nut driver, replaced the bottom pan in the oven, slid the door back on its two hinges and started it up. Works perfectly. Thanks Partselect. You guys are great and I had the replacement my mail in about 5 working days!
Read less
Was this helpful?
Thank you for voting!
oven wouldn't heat
2 of 2 people
found this instruction helpful.
-
Dana from Windchester, IN
- Really Easy
- 15 - 30 mins
-
Nutdriver
removed 2 screws and unpluged ingiter plug ed new igniter in replaced screws and worked fine
Was this helpful?
Thank you for voting!
oven would take a very long time to warm
2 of 2 people
found this instruction helpful.
-
Barry from East Islip, NY
- Really Easy
- 15 - 30 mins
-
Nutdriver
took out both racks and under tray at bottom of stove no tools required.
used a nut driver to remove both screws holding ignighter in place ,pulled wires up gentily and remove from standard clip by pushing ends in.
clip new ignighter in place push wires down again and install 2 screws . put all back together and it works like ... Read more new .
used a nut driver to remove both screws holding ignighter in place ,pulled wires up gentily and remove from standard clip by pushing ends in.
clip new ignighter in place push wires down again and install 2 screws . put all back together and it works like ... Read more new .
Read less
Was this helpful?
Thank you for voting!
igniter burned out
2 of 2 people
found this instruction helpful.
-
David from Milton, MA
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers, Wrench set
Removed bottom tray of oven, unscrewed gas pipe, removed old igniter and replaced it. Spent some extra time digging around for leads, etc. before discovering that my new igniter was identical to the old one and all I had to do was plug it in.
Was this helpful?
Thank you for voting!
oven would not light
2 of 2 people
found this instruction helpful.
-
gary from covington, LA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
New parts matched up perfectly. Undid screws holding old igniter, hardest part of procedure because one screw was frozen and broke off. Pulled stove out and new igniter"s connector was identical. Pushed stove back into place and it lighted on the first try.
Was this helpful?
Thank you for voting!
gas burners would not light with electric ignighters
3 of 5 people
found this instruction helpful.
-
Leo from Temple, TX
- Easy
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
using the diagram shown on line Looked up the ignition module and ordered it by phone. Received it the next day and installed it within the hour. Previously I had called the repairman and he said it would be a couple of weeks before he could look at it and a service call was $75 plus parts..I fixed it for the cost of the module $34. I
... Read more
am very satisfied.
Read less
Was this helpful?
Thank you for voting!
oven would not turn on
2 of 3 people
found this instruction helpful.
-
Robert from Clymer, NY
- Easy
- 15 - 30 mins
-
Screw drivers
I first removed oven racks.then I removed bottom of oven by sliding locks,then lifting out bottom.Next I removed screw holding e. control cove,then removed cover.Igniter plug was exposed,I then unpluged egniter. I next removed 2 screws holding burner and igniter .I removed igniter and burner as a unit. removed 1 screw from igniter,and rep
... Read more
laced igniter on burner.Then assembled every thing in reverse order,and tested Oven worked perfectly.
Read less
Was this helpful?
Thank you for voting!
igniter glowed but oven would not light
2 of 3 people
found this instruction helpful.
-
edward from euclid, OH
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers
It looked like an easy fix. the igniter had a plastic clip. A simple R&R. Removed old igniter from its mount, removed plate to get access to wires, removed insulation. Tried to pull the old wires out of its location. It was hung up and I spent 1/2 hr. trying to free it. No go. I thought I'd have to remove oven from its cabinet. I removed
... Read more
six screws and it would not come forward. I felt the under side of the oven thru lower door of cabinet and found out that was where gas was connected. No way was I disconnecting the gas. Pushed oven back in, reinstalled screws and decided to cut old wires and splice in the new igniter. WENT BACK AND READ THE INSTRUCTIONS! Supplied were 4 ceramic wire nuts. Then the light bulb went on! OKAY! I got a marker and marked the top wire on the old igniter to identify it after I cut the wires as close to the back of the old igniter as I could with a pair of side cutters. I then cut the wires as close as I could to the plastic clip on the new igniter. Striped off 3/8 in. from all wire ends and spliced the wires together using the wire nuts. I stuffed the wires as far as possible back into the hole they came from, replaced all old and some new insulation into the hole. The supplied cover would not work, screw holes would not line up and would have fit poorly. I reused the old hole cover. Screwed new igniter to its mount. Turned on the oven and thought I screwed up. I waited about 30 seconds before I saw it start to glow. WHEW! I got it right! After a few more seconds, the gas came on and the oven burner ignited. The really hard part was putting the oven door back on its mount. That door was heavy and wouldn't line up on the first try.......
Maybe if I read the instructions thoroughly the first time before I started, I could have cut my time in half and saved a lot of cussin'. CUTTING THE WIRES WAS AN "OPTION"! That's why they supplied the ceramic wire nuts!....... Dinner is in the oven right now. Smells good!
Maybe if I read the instructions thoroughly the first time before I started, I could have cut my time in half and saved a lot of cussin'. CUTTING THE WIRES WAS AN "OPTION"! That's why they supplied the ceramic wire nuts!....... Dinner is in the oven right now. Smells good!
Read less
Was this helpful?
Thank you for voting!
Replace clock-adjust knob
2 of 3 people
found this instruction helpful.
-
OSCAR from BRISTOL, CT
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers
Although normally a push fit, we drilled and tapped a #6-32 cross hole and used a set-screw to attach the small knob.
The original knob is still hiding somewhere but, thanks to PartSelect we are back in business !
The original knob is still hiding somewhere but, thanks to PartSelect we are back in business !
Was this helpful?
Thank you for voting!
The back of the knob was broken and looked bad
2 of 3 people
found this instruction helpful.
-
VONDA L from BAILEY, CO
- Really Easy
- 15 - 30 mins
-
Screw drivers
I got on-line, found your website, put in the required information (model #, brand, part, etc.) and ordered. Before ordering however, I measured, looked at the picture on-line, and compared to the part I needed. It looked right. I ordered, and the parts came in a timely manner. Got an e-mail saying they were ordered, then another e-mail s
... Read more
aying they were shipped. Got the parts, installed, they look so good. I'm very pleased. Thanks!
Read less
Was this helpful?
Thank you for voting!
corroded burners
2 of 3 people
found this instruction helpful.
-
Daniel from Can Francisco, CA
- Really Easy
- Less than 15 mins
-
Wrench (Adjustable)
Unscrew the burners an install new ones! Anyone could do this.
Was this helpful?
Thank you for voting!
Couldn't Read the oven Temp on knob.
2 of 3 people
found this instruction helpful.
-
David from Winfield, IL
- Really Easy
- Less than 15 mins
-
Screw drivers
Called Magic Chef for part and they said the oven was to old. Looked up Partselect.com and found part I needed. Shipped fed ex and pull off knob, unscrewed old skirt, clean area, screwed on new part and replace knob. Looks like a new stove.
Unbelievable that Magic Chef didn't know about this site. I will always check here first for ... Read more what I need.
Dave
Illinois
Unbelievable that Magic Chef didn't know about this site. I will always check here first for ... Read more what I need.
Dave
Illinois
Read less
Was this helpful?
Thank you for voting!
Replaced burner
2 of 3 people
found this instruction helpful.
-
Ramiro from Bernalillo, NM
- Easy
- Less than 15 mins
-
Wrench set
Went well
Was this helpful?
Thank you for voting!
Original burner was eroded on the bottom and flame was coming from undernealth the burner
2 of 3 people
found this instruction helpful.
-
Joe from Staten Island, NY
- Really Easy
- Less than 15 mins
Very easy. I disconnected the original burner with one turn as well as the two wire connections for the electronic igniter. I then connected the wires to the same positions on the new burner and placed the new burner in place with one half turn to match the indented openings to secure the burner tightly in place.
Was this helpful?
Thank you for voting!