EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3187 - Instructions

All Instructions for the 3187
91 - 105 of 356

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Bad Gasket
2 of 3 people found this instruction helpful.
  • javier from Santa Ana, CA
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
I just twist the burner, pulled it out, disconect the two wires. Reconect the wires to the new burner and placed back .
Was this helpful?
Thank you for voting!
I needed a broiler pan
4 of 9 people found this instruction helpful.
  • Rhoda P. from Secaucus, NJ
  • Really Easy
  • Less than 15 mins
I took the broiler pan out of the shipping container and put it in the oven.
Was this helpful?
Thank you for voting!
oven would not heat up fully, smelled of gas.
1 person found this instruction helpful.
  • Brian from Spotswood, NJ
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Took off the top plate at the bottom of the oven, and the flame spreader, removed 2 screws on the igniter, pulled out the broiler tray and unplugged it. Took longer to get off the floor than it did to replace the part.
Was this helpful?
Thank you for voting!
oven would not light reliably.
1 person found this instruction helpful.
  • Joe from West Winfield, NY
  • Easy
  • Less than 15 mins
  • Screw drivers
Just like the example I removed the oven base, removed the two screws holding the igniter. Pulled out the wires opened the connector, plugged in the new igniter put everything back and turned on the oven. The oven now lights better than it did when new. And it holds a steady temp.
Was this helpful?
Thank you for voting!
Igniter for oven not working
1 person found this instruction helpful.
  • RONNIE from SAG HARBOR, NY
  • Easy
  • Less than 15 mins
  • Wrench set
Instead of buying a new range my son said he could replace the part so I looked your company up on internet and had it shipped. Three days later I was cooking with gas again! Thanks!
Was this helpful?
Thank you for voting!
Sealed burner was rusted out. Had a hole in it.
1 person found this instruction helpful.
  • Jeanne from ELMIRA, MI
  • Very Easy
  • Less than 15 mins
Unplugged two connectors and plugged into new burner. Couldn't have been easier! Also, I was so pleased that it matched the other three burners exactly!
Was this helpful?
Thank you for voting!
Stove Would Not Light To Heat Up.
1 person found this instruction helpful.
  • Nola from Enid, OK
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Removed grates and bottom plate two screws holding it. Turn oven light on and unwire the wire. Unscrewed the two screws and replace. This took my husband about ten min. And for him he says that this was a walk in the park. He says if he can do it anyone can. This was one of the easy honey dews. Good luck with yours. Nola & keith
Was this helpful?
Thank you for voting!
no spark on top burners
2 of 4 people found this instruction helpful.
  • eric from winter haven, FL
  • A Bit Difficult
  • 15 - 30 mins
  • Pliers, Screw drivers
part was by the brolier drawer inside under stove removed 2 screws on cover/ part was attached to cover removed module line 1-2 fit/ had to use supplied disconects crimped on 4 burner wire leads/taped around module w/ elec. tape put back 2 screws finished. works now.
Was this helpful?
Thank you for voting!
Burner worn out
1 person found this instruction helpful.
  • Robert from LORENA, TX
  • Very Easy
  • Less than 15 mins
Turned burner about 1/16 turn to left. Lifted burner from stove. Disconnected two wire connectors. Connected same wires to new burner. Set burner in place and turned 1/16 turn to right. Tested burner. Lighter worked on first attempt and burned perfectly. Took about 3 1/2 minutes.
Was this helpful?
Thank you for voting!
igniter failed to ignite
1 person found this instruction helpful.
  • Gino from ARLETA, CA
  • Really Easy
  • Less than 15 mins
  • Socket set
Replaced the igniter by removing 2 screws, pulling on the wires to pull the connector in from the back thru the oval opening, screwing in the the new element, reconnecting the wires, pushing the connector back and that did it.
Was this helpful?
Thank you for voting!
Old seal breaking off oven door. Oven not baking food well, wasting heat and fuel.
1 person found this instruction helpful.
  • Mz from COLUMBIA, ME
  • Very Easy
  • Less than 15 mins
  • Pliers
Used pliers to remove clips and old seal. Snap in new seal. DONE! Less than 5 mins.
Was this helpful?
Thank you for voting!
The oven bottom was warped and could not be positioned properly in the oven.
1 person found this instruction helpful.
  • Tara from ALBANY, NY
  • Easy
  • 15 - 30 mins
Removing the old oven bottom was easy...as it was already outside of its slots. Installing the new one was pretty easy. I placed the oven bottom in the front slots first...then the rear slots...no tools necessary.
Was this helpful?
Thank you for voting!
Simply remove and install new parts
1 person found this instruction helpful.
  • Jacob from LITTLE CANADA, MN
  • Really Easy
  • 15 - 30 mins
Overall, it was painless and easy with zero problems
Was this helpful?
Thank you for voting!
The oven igniter would glow red but gas did not come on to light the burner.
1 person found this instruction helpful.
  • Ernest from CINCINNATI, OH
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers, Wrench (Adjustable)
I watched a repair video, unplugged the electric,turned off the gas valve and disconnected the gas line. removed the shelves and burner tray. removed 2 screws and unplugged the igniter. Replaced the igniter and put tray and racks in.Hooked up gas and plugged in the electrical plug. Job done....
Was this helpful?
Thank you for voting!
No heat in oven
1 person found this instruction helpful.
  • Cynthia from AURORA, MN
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
Checked igniter it glowed but never got hot enough to open gas valve. I switched igniter from broiler to oven and oven burner lit. Switched igniter back to broiler as wires were shorter than the oven igniter. Ordered part from number and picture comparison. It took about 20 minutes to get it installed and all stove parts back together.
Was this helpful?
Thank you for voting!
All Instructions for the 3187
91 - 105 of 356