EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3187 - Instructions

All Instructions for the 3187
46 - 60 of 356

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
The oven igniter lit up but the valve wouldn't release the gas to ignite.
4 of 4 people found this instruction helpful.
  • John from Wisconsin Rapids, WI
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
I would have never guessed that the problem would have been with the igniter since it was glowing. After reading some of the entries in your trouble shooting area it was clear that this is common and that it likely was the igniter so I simply took off the two screws that hold it in place, inplugged the old, plugged in the new, secured wi th the screws and it worked. The only problem I encountered was that when I unplugged the old igniter the plug fell down into the bowels of the oven and I had to fish out with a twisted up hanger.
Was this helpful?
Thank you for voting!
Hammered Orifice tubes
4 of 5 people found this instruction helpful.
  • Devin from Santaquin, UT
  • Easy
  • 15 - 30 mins
  • Wrench set
1. Screw the burners counterclockwise 45 degrees to remove each burner. Some gave easily while others were baked on.
2. Remove one philips-head screw per burner.
3. disconnect ignition wire from each burner.
4. remove stovetop.
5. remove the previous hammered orifice and tube assembly by unscrewing 4 nuts.
6. atta ch the new assembly and follow steps 1-4 in reverse order.
Was this helpful?
Thank you for voting!
oven door gasket torn
4 of 5 people found this instruction helpful.
  • Ovide N from Abbeville, LA
  • Really Easy
  • Less than 15 mins
ordered wrong part, called, was sent return number, sent part back, account credited ... easy return policy ... friendly people, good job
Was this helpful?
Thank you for voting!
oven wouldn't light
4 of 5 people found this instruction helpful.
  • peter from marine city, MI
  • Really Easy
  • Less than 15 mins
  • Screw drivers
The gas valve (recently new from partselect) wouldn't open, or sometimes it would open just enough to let some gas escape! I read from others that just because the igniter was glowing, it might not be putting out enough voltage to trip the gas valve. A check of this confirmed that it was sending just over 3V to the valve - not enough to f ully open it. I felt confident that springing for the $60 would solve the problem once and for all. After replacing the igniter, the oven lights in 10 sec or less, and this is a 26-year-old appliance! PartSelect to the rescue again!
Was this helpful?
Thank you for voting!
Panel light burnt out after 10 years
4 of 5 people found this instruction helpful.
  • Pamela from La Junta, CO
  • Really Easy
  • Less than 15 mins
I live in a small town in South East Colorado. We have just a Walmart and Sears and a few smaller hardware stores. I checked all of them to try to find this 25 1/2 inch Fluorescent Light Bulb, and nobody carried one. I would have had to drive 70 miles to find one. The Service of Partselect was wonderful and the bulb showed up in just 4 days. I was lost without this light. I have bought a few other items for my older appliances in the past from Partselect. com and was very happy with the service and how easy the web page is to navigate. .
Was this helpful?
Thank you for voting!
Oven and burners wouldn't light
3 of 3 people found this instruction helpful.
  • Kory from Collingswood, NJ
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Easy repair. I removed the module housing at the back of the stove (two screws) and slipped the wires off the old spark module (I had to use pliers to gently pull one or two wires off--it's an old stove). The existing wires slipped right on the new module. I did have to use the mounting adapter that came with the kit, but that was the fiddliest part of the whole repair. It took me longer to move the stove out and back than it did to do the repair.
Was this helpful?
Thank you for voting!
couldn't see the numbers on the dial anymore
3 of 3 people found this instruction helpful.
  • trudi from pleasant prairie, WI
  • Really Easy
  • Less than 15 mins
  • Screw drivers
First I removed the two screws that held the element in place. I removed the old element and placed the new part in place, then replaced the screws.
Was this helpful?
Thank you for voting!
Oven wouldn't heat.
3 of 3 people found this instruction helpful.
  • Thomas from La Crescenta, CA
  • Easy
  • Less than 15 mins
  • Nutdriver
Slid two latches at rear of bottom oven pan toward door, pulled pan up at rear of oven and removed. Igniter exposed, removed two self-tapping screws with nutdriver, pulled wires surrounded by insulation up out of hole in ovenfloor an unsnapped plastic connector wired to old igniter. screwed new igniter to bracket, reconnected wires, pus hed connectors into hole and shoved new insulation around wires, fitted bottom pan and turned on oven. Works better than new, Thanks PARTSELECT.
Was this helpful?
Thank you for voting!
No spark, bad igniter
3 of 3 people found this instruction helpful.
  • Tom from REDDING, CA
  • Really Easy
  • 15 - 30 mins
1. Grab the old burner and twist counter-clockwise. 2. Unplug the wire from the old igniter, simply pull off. 3. Take new burner/igniter (this new one comes all-in-one) and reattach the wire to the igniter underneath. 4. Place the burner so the 'nubs' line up with the stove top and then twist clockwise a short amount, it should tu rn slightly to lock in place. 5. Test. Mine sparked and started better than it has since i have had the stove
Was this helpful?
Thank you for voting!
The old sealed burner cap had rusted out allowing gas flame around the base of the cap.
3 of 3 people found this instruction helpful.
  • John from Stephentown, NY
  • Really Easy
  • Less than 15 mins
Note the position of the electrode on the side of the old burner cap. Turn the old burner cap one-eighth turn counter-clockwise to loosen and remove it. Raise the burner cap and disconnect the push-on connector wires from the ground and electrode. Clean the surface and connect the electrode and ground connector wires correctly to the n ew burner cap and place the burner cap back in the opening, positioning the electrode at the same orientation as it was with the old burner cap. Turn the cap one-eighth turn clockwise until the burner is snug. Turn on the burner control to test that the burner functions correctly. Make sure there is no smell of propane or gas when the burner is not in use which might indicate that the burner is not properly fitted snugly.
Was this helpful?
Thank you for voting!
Leaking gas from sides of burner
3 of 3 people found this instruction helpful.
  • Homero from SEAGOVILLE, TX
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
Counterclockwise turn old burner to remove. Unplug attachment wires. Replug wires place back in place turn clockwise. Done.
Was this helpful?
Thank you for voting!
Gas range and top oven does not light up
3 of 3 people found this instruction helpful.
  • Albert from Boston, MA
  • Easy
  • 15 - 30 mins
  • Screw drivers
I pulled out the gas range, unplugged the unit from the outlet. Unscrewed about two panels, one is the black cardboard panel located on top, then the aluminum main panel.

Located the spark module, unscrewed the unit from resting plate. Did not change the plate, although the new unit came with a new one, but it doesn't fit. S o I just rested the new one on the old plate.

Pulled each wire slowly out and inserted it onto the new spark module.

Screwed in all the panels back and returned the stove to its proper place.

The range now works as well as the oven, but my broiler still does not light up.
Was this helpful?
Thank you for voting!
Oven wouldn't heat/ turn on
3 of 3 people found this instruction helpful.
  • Diane from NEW HAVEN, MO
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
If you watched the video on installing the part it IS that easy. The connector piece matched exactly with what my oven already had so it was as simple as disconnecting the old piece and plugging in the new piece. There was no hidden challenges or obstacles to overcome. The oven works perfectly fine there was a slight smell when I first turned on the oven but I am attributing that to a new part. The smell did go away. I am 24 years old and a female who has limited knowledge in electrical/oven work.
Was this helpful?
Thank you for voting!
Self tapping screws stripped out, one broke in mounting hole
3 of 3 people found this instruction helpful.
  • Scott from FORT WORTH, TX
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Punched out broken screw. Drilled out damaged threads to same size as igniter mounting holes. I used nuts, bolts and lock washers to mount igniter. Would have been very easy if mounting screws had come out. Video very helpful.
Was this helpful?
Thank you for voting!
OVEN WOULD NOT HEAT
3 of 3 people found this instruction helpful.
  • Mary from MEADVILLE, PA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
TOOK OVEN BOTTOM APART AND LOSSENED OLD IGNITERTHEN WENT TO BACK OF OVEN TOOK BACK OFF DISCONETED OLD IGNITER PULLED THE NEW THUR AND CONNECTED PUT BACK ON THEN ATTACHED FROM THE FRONT PUT OVEN BACK TOGATHER THEN TURNED OVEN ON IT WORKED I DID IT MYSELF I AM 64 YEAR OLD WOMEN
Was this helpful?
Thank you for voting!
All Instructions for the 3187
46 - 60 of 356