EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3187 - Instructions

All Instructions for the 3187
31 - 45 of 356

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Over wouldn't light.
8 of 12 people found this instruction helpful.
  • Bob from South Beloit, IL
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Wrench (Adjustable)
Saw that the igniter came on, but no gas flow.
Unpluge stove. Remover bottom of oven to have access to flow valve. Remored sheet metal cover.
Removed burner. Unpluged flow valve and removed it.
Was this helpful?
Thank you for voting!
spark ignition in stove failed to turn on burnes.
7 of 10 people found this instruction helpful.
  • David from Upland, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers
Remove burnes and top oven glass, , identified cables for each burner. Unpluged cables, remove old ignition module, drill a hole to install new module. Place module in location. I had to figure out what cables were for the right burner as after placing in the same location as old ignition Module it turned out that they were not identical. I did have to cut old plugs to be able to install cables to new ignition module. If the new part came with and adapter to old cables, as old plugs have small connectors, the new one comes with larger plugs. That would have made it esier.
Was this helpful?
Thank you for voting!
Burners would not ignite
6 of 7 people found this instruction helpful.
  • Charles from Kalamazoo, MI
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Removed cover from igniter, took off wires, replaced wires on new one, secured in place, put cover back on.
Was this helpful?
Thank you for voting!
Igniters were flaky on 2 burners and almost dead on 2
7 of 10 people found this instruction helpful.
  • Matt from Craig, CO
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
The part didn't come with installation instructions specific to any stove/oven so I went by a previous testimony on this website and pulled out the stove, and started to remove the side panel to get access. Well turns out I could have done the whole repair in place because on my Maytag the igniter source is accessible by removing the uti lity drawer and it's mounted on a small galvanized steel panel at the left side which hides the part directly. The existing spade connectors were the right size for me but I did have to crimp them tighter (which was perhaps part of the initial problem). After installation, the spark is much more powerful and all burners lit first couple "clicks".
Was this helpful?
Thank you for voting!
Burners would not ignite flame...Had to start with match.
6 of 7 people found this instruction helpful.
  • Richard from Los Angeles, CA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
Removed the old burners with a Plumbing Pipe Wrench by turning 1/4 turn counter clockwise. Disconnected (2) wires and replaced with new Sealed Burners. The simmer burner wires were slightly diffrent from the original but they do fit by opening the connector with screwdriver and then clamping once wire inserted.
Was this helpful?
Thank you for voting!
My range is 13+ yrs old and the knobs and bezels were looking very sad and worn.
6 of 7 people found this instruction helpful.
  • Susan from Aiken, SC
  • Really Easy
  • Less than 15 mins
I simply popped off the old ones, cleaned around opening and popped in the new ones.
And what a difference. The old ones were an off white color and I replaced them with white ones. Such an easy way to spruce up the stove!!
Was this helpful?
Thank you for voting!
Bad Door Gasket.
6 of 8 people found this instruction helpful.
  • Donald from Schuylkill Haven, PA
  • Really Easy
  • Less than 15 mins
  • Pliers
First I took the new gasket out of the plastic bag to make sure it was the right size. Then I proceded to take the old gasket out by pulling it with a long noise pliers. Then I took the new gasket and went around the door putting the pins in the holes that, the old gasket was in. That,s about it.
Was this helpful?
Thank you for voting!
One element of number display did not light
7 of 11 people found this instruction helpful.
  • Lawrence J from BENTON, AR
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
clock is in top of double oven. Dis-assembly and access to the clock was a puzzle. Four screws in the top of the oven were the solution. The clock panel then folded out and access to three plug-ins and four screws allowed access to the clock. remounted the clock with four screws and replaced plugs. (watch carefully order of wiring) Re-p ower on the oven and set clock. NOTE: Cover said Magic Chef but Label said MayTag
Was this helpful?
Thank you for voting!
Electronic spark ignition would not ignite intermittently.
5 of 5 people found this instruction helpful.
  • Charles from Old Bridge, NJ
  • Easy
  • 15 - 30 mins
  • Screw drivers
The spark moule was accessed by removing the bottom storage draw and removing the 2 phillips screws that held the spark module bracket to the frame of the stove located on the rear right side of the draw opening. The new module did come with new spade connectors that reqires cutting the existing connectors off and splicing and crimping th e new connectors to the wires for each of the four burners depending on the model stove. Also I had to use zip ties to secure the new module to the original mounting hardware since the replacement module is not a direct fit. Each of the four burners now instantaneoulsly ignite when turned on. I will buy from Partselect.com in the future. Thank you.
Was this helpful?
Thank you for voting!
the lines were broken
7 of 11 people found this instruction helpful.
  • RONALD from DELAVAN, WI
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
1) removed 2 lines 2) removed 4 screws 3)pulled out old element4) relaced new part 5)installed screws 6) install lines &tighten
Was this helpful?
Thank you for voting!
Faulty bulb receptacle
10 of 20 people found this instruction helpful.
  • Kenneth from Lynchburg, VA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Unplugged the stove and removed the back panel, disconnected the wires from the old receptacle, removed it, inserted the new receptacle, connected the wires, put the back panel of the stove on, plugged in the stove and then checked to see if the bulb was now burning. Success!
Was this helpful?
Thank you for voting!
light bulb in water ice freezer door went bad
8 of 14 people found this instruction helpful.
  • Carl from RIVERSIDE, CA
  • Very Difficult
  • More than 2 hours
  • Screw drivers
I didn't. Don't know how to get to light bulb to change it for this specific model
Was this helpful?
Thank you for voting!
Stove seal fell apart
5 of 6 people found this instruction helpful.
  • Teresa from Washougal, WA
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Removed old seal parts and had to cut new part to put into space but it went in without difficulty and has sealed the stove door tight again.
Was this helpful?
Thank you for voting!
oven would not turn on flame
6 of 10 people found this instruction helpful.
  • Michael from Secaucus, NJ
  • Easy
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
first I removed the 6 screws that hold the oven in place in the oak cabinet. I slid a kitchen chair in place in front of the oven,then I slid the oven out of the cabinet cut out. Although the gas flex was still connected, I unpluged the electrical connection. I removed the old igniter, unpluged the igniter harness in the rear compartment. Then I installed the igniter in reverse.When the oven was pushed back in and secured with the 6 screws,I turned on and tested. Igniter glowed orange and the flame came on. Job was complete in 20 minutes.
Was this helpful?
Thank you for voting!
Timer know would no longer set the time...
5 of 7 people found this instruction helpful.
  • Rachael from Adams, MA
  • Very Difficult
  • More than 2 hours
  • Screw drivers
I removed the screws holding the bezel, removed the control panel frame, unhooked the four wires from the timer, and removed the timer. I cut the glue holding the circuit board into the frame and removed the circuit board. I unsoldered the faulty encoder switch, dissassembled the switch, determined the correct specifications for the swit ch, and ordered the nearest equivalent from an electronics supplier. I modified the new encoder to accept the shaft from the old encoder and I re-drilled the circuit board to fit the new encoder. I then soldered and wired the encoder, reversing the wires to correct the direction of rotation. I then reinstalled everything and added the knob purchased from partselect.com. Now it works. Tough repair - not for the faint of heart or those of average skill. But for the record, installing the knob was of course child's play and took only a moment.
Was this helpful?
Thank you for voting!
All Instructions for the 3187
31 - 45 of 356