3131 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Could not turn the oven on or off.
7 of 7 people
found this instruction helpful.
-
Christine from Indio, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
Lifted the top up, only a few inches as the possibality of kinking the gas line was a issue. Took two screws out and replaced the unit, threaded the thermostat down through the oven. It was a breeze. I am 68 year old woman and did I myself.
Most importantly, the process of getting the part was amazing, ordered it in the AM and receiv ... Read more ed it the next day (no extra charge)and by miday the range was good as new. Great service!
Most importantly, the process of getting the part was amazing, ordered it in the AM and receiv ... Read more ed it the next day (no extra charge)and by miday the range was good as new. Great service!
Read less
Was this helpful?
Thank you for voting!
Seal was fallinig off
7 of 8 people
found this instruction helpful.
-
Marilyn from Fresno, CA
- Really Easy
- Less than 15 mins
My husband did it. I was not there to see it. He said it took less than one minute, just snapped in and worked beautifully.
Was this helpful?
Thank you for voting!
Oven floor panel was warped.
8 of 11 people
found this instruction helpful.
-
Cindy from Colton, CA
- Really Easy
- Less than 15 mins
It was so easy, I pushed the panel towards the back and lifted the front up then lifted it right out. I am so glad that you had the part. I ordered it and when it got here, I just sliped it right in, perfect fit! Thank you so much! Cindy Brison
Was this helpful?
Thank you for voting!
oven temperature not reaching setting/temp. up and down
7 of 8 people
found this instruction helpful.
-
Ellen from Schenectady, NY
- Easy
- 15 - 30 mins
-
Screw drivers
Removed back of stove, removed screws from sensor inside oven, unplugged connector from back of stove, pulled sensor out through oven; installed new sensor, replaced back of stove. Set the oven to bake, waited for it to pre-heat; the oven thermometer showed that the same problem was occurring, the sensor replacement didn't work.
Was this helpful?
Thank you for voting!
thermostat went out
9 of 14 people
found this instruction helpful.
-
brenda from redding, CA
- Easy
- 15 - 30 mins
-
Screw drivers
Had to take off burners and lift off top. Then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and removed old element. Then I did all steps in reverse to install new thermostat.
Was this helpful?
Thank you for voting!
Oven temperature lower then setpoint.
7 of 8 people
found this instruction helpful.
-
Robert from Massapequa, NY
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
After shutting the main valve behind stove. Removed all shelves and rear cover from stove. Unplugged the plug to the sensor. Removed the two mounting screws and pulled the old sensor out. Installed new sensor and plugged it in again. After reinstalling the rear cover and shelves, replugged in power, openned the gas valve behind the stove
... Read more
and tested with soapy water to make sure there wasn't ant developed leaks. Turned on oven with a test thermometer in it. Monitored operation and now oven temperature is roughly 10 to 20 degrees to the setpoint.
Read less
Was this helpful?
Thank you for voting!
Oven wouldn't ignite
8 of 11 people
found this instruction helpful.
-
John from Caliente, CA
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Removed oven door (easy it lifted right off) and remove oven bottom (also easy, no tools). removed two screws holding igniter and unplug old igniter from power. Re-attached new igniter and re-assembled oven.
Parts came very quickly from PartSelect. Good service.
Parts came very quickly from PartSelect. Good service.
Was this helpful?
Thank you for voting!
The range burners would not catch a spark and ignite. They would just keep clicking with no ignition.
8 of 11 people
found this instruction helpful.
-
Adrienne from Lake Havasu City, AZ
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
I had an appliance repair rep do the replacement. He made it look relatively easy.
The repair man first turned off the breaker to the range and confirmed there was no power to the range.
After lifting off the range top cover exposing the burner igniters, he unhooked and removed the igniters. He opened the lower oven door exp ... Read more osing the screws which hold the front knob plate in position. He took those out. After loosening the knob plate he was able to unscrew and raise the inside cover which exposes the wires and the spark module.
My spark module was located in the front left corner area tucked a little under the knob plate. That is another reason why he had to loosen the plate. The replacement part was a universal part so he had to do a little work on the wire connectors but it only took a couple of minutes. Once he configured the wire ends, he was able to plug in the new spark module and put the top back together again.
The repair man knew exactly what to do and made it look relatively easy. I did not want to tackle this problem because I did not know exactly where the spark module was since some models have them in the back of the oven and the oven has to come out from the wall. Also, the wire connections had to be worked with a little and he knew exactly how to do that.
The repair man took about 45 minutes from beginning to end with most of that time spent getting to the part and putting it back together. The replacement itself took only about 10 minutes.
The repair man first turned off the breaker to the range and confirmed there was no power to the range.
After lifting off the range top cover exposing the burner igniters, he unhooked and removed the igniters. He opened the lower oven door exp ... Read more osing the screws which hold the front knob plate in position. He took those out. After loosening the knob plate he was able to unscrew and raise the inside cover which exposes the wires and the spark module.
My spark module was located in the front left corner area tucked a little under the knob plate. That is another reason why he had to loosen the plate. The replacement part was a universal part so he had to do a little work on the wire connectors but it only took a couple of minutes. Once he configured the wire ends, he was able to plug in the new spark module and put the top back together again.
The repair man knew exactly what to do and made it look relatively easy. I did not want to tackle this problem because I did not know exactly where the spark module was since some models have them in the back of the oven and the oven has to come out from the wall. Also, the wire connections had to be worked with a little and he knew exactly how to do that.
The repair man took about 45 minutes from beginning to end with most of that time spent getting to the part and putting it back together. The replacement itself took only about 10 minutes.
Read less
Was this helpful?
Thank you for voting!
The F3 error code displayed and beeped during use of the oven and oven shut down.
7 of 9 people
found this instruction helpful.
-
Debra from Colts Neck, NJ
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers
My husband and I began to pull the oven out and I realized that it was too heavy for me to hold. Luckily we were able to get another man to help. Other than that it was easy. Also, it took us awhile to figure out which screws secured the oven into the cabinet. We saved over $1000.00 on a new oven and installation. Kudos to everyone who
... Read more
added their comments! They gave us courage to give it a try.
Read less
Was this helpful?
Thank you for voting!
F3 code, oven wouldn't heat.
8 of 12 people
found this instruction helpful.
-
Shaun from Kimball, NE
- Really Easy
- Less than 15 mins
-
Screw drivers
First pulled the oven out and noticed how dirty the floor was underneath. Bachelors are BAD housekeepers. Next I removed the oven door (just slides off the hinges) to make it easier to reach in and unscrew the two screws holding the sensor in place in the upper left back of oven. Screws came out easily. Then I removed the back panel by re
... Read more
moving the six screws holding it in place. I unsnapped the temp sensor wiring connection, then pulled the probe out from the front (inside the oven). Installed the new probe by feeding the wires and connector through from the front (inside the oven) and attached it with the two screws. Then went to the back again, snapped the wiring connectors together, and replaced the back panel. Then I scrubbed the floor, pushed the range back in place, reinstalled the door, and gave it a test run. PERFECTION! Heated to within five degrees of setting. EASIEST REPAIR JOB I'VE EVER DONE!
Read less
Was this helpful?
Thank you for voting!
black dirty burner grates
14 of 31 people
found this instruction helpful.
-
Carolyn from St. George, UT
- Really Easy
- Less than 15 mins
replaced grates
Was this helpful?
Thank you for voting!
Igniters were flaky on 2 burners and almost dead on 2
7 of 10 people
found this instruction helpful.
-
Matt from Craig, CO
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
The part didn't come with installation instructions specific to any stove/oven so I went by a previous testimony on this website and pulled out the stove, and started to remove the side panel to get access. Well turns out I could have done the whole repair in place because on my Maytag the igniter source is accessible by removing the uti
... Read more
lity drawer and it's mounted on a small galvanized steel panel at the left side which hides the part directly. The existing spade connectors were the right size for me but I did have to crimp them tighter (which was perhaps part of the initial problem). After installation, the spark is much more powerful and all burners lit first couple "clicks".
Read less
Was this helpful?
Thank you for voting!
Burners would not ignite
6 of 7 people
found this instruction helpful.
-
Charles from Kalamazoo, MI
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Removed cover from igniter, took off wires, replaced wires on new one, secured in place, put cover back on.
Was this helpful?
Thank you for voting!
Burners would not ignite flame...Had to start with match.
6 of 7 people
found this instruction helpful.
-
Richard from Los Angeles, CA
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
Removed the old burners with a Plumbing Pipe Wrench by turning 1/4 turn counter clockwise. Disconnected (2) wires and replaced with new Sealed Burners. The simmer burner wires were slightly diffrent from the original but they do fit by opening the connector with screwdriver and then clamping once wire inserted.
Was this helpful?
Thank you for voting!
spark ignition in stove failed to turn on burnes.
7 of 10 people
found this instruction helpful.
-
David from Upland, CA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
Remove burnes and top oven glass, , identified cables for each burner. Unpluged cables, remove old ignition module, drill a hole to install new module. Place module in location. I had to figure out what cables were for the right burner as after placing in the same location as old ignition Module it turned out that they were not identical.
... Read more
I did have to cut old plugs to be able to install cables to new ignition module. If the new part came with and adapter to old cables, as old plugs have small connectors, the new one comes with larger plugs. That would have made it esier.
Read less
Was this helpful?
Thank you for voting!