3131 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
oven door gasket torn
4 of 5 people
found this instruction helpful.
-
Ovide N from Abbeville, LA
- Really Easy
- Less than 15 mins
ordered wrong part, called, was sent return number, sent part back, account credited ... easy return policy ... friendly people, good job
Was this helpful?
Thank you for voting!
oven wouldn't light
4 of 5 people
found this instruction helpful.
-
peter from marine city, MI
- Really Easy
- Less than 15 mins
-
Screw drivers
The gas valve (recently new from partselect) wouldn't open, or sometimes it would open just enough to let some gas escape! I read from others that just because the igniter was glowing, it might not be putting out enough voltage to trip the gas valve. A check of this confirmed that it was sending just over 3V to the valve - not enough to f
... Read more
ully open it. I felt confident that springing for the $60 would solve the problem once and for all. After replacing the igniter, the oven lights in 10 sec or less, and this is a 26-year-old appliance! PartSelect to the rescue again!
Read less
Was this helpful?
Thank you for voting!
Broken levelling leg
5 of 8 people
found this instruction helpful.
-
Linda from Oneida, NY
- Really Easy
- Less than 15 mins
Took the old levelling leg out and screw the new one in.
Was this helpful?
Thank you for voting!
One of four burners did not start (no sparks)
5 of 8 people
found this instruction helpful.
-
Nataly from Brooklyn, NY
- Really Easy
- Less than 15 mins
Turned burner about a quarter of a turn, lifted, disconnected wires, connected them to a new burner and replaced it.
Was this helpful?
Thank you for voting!
the burner cap on my maytag gas range was rusty on the inside and didn't allow the cap to sit flush-causing gas and flames to leak from under the cap
4 of 5 people
found this instruction helpful.
-
julie from harrodsburg, KY
- Really Easy
- Less than 15 mins
installation was very simple and took less than 5 minutes. first unscrew the burner cap and then remove the 2 wires. to replace reconnect the 2 wires to the new cap and twist cap into place-simple.
Was this helpful?
Thank you for voting!
Just unscred the 2 screw on the Thermometer
4 of 5 people
found this instruction helpful.
-
WILLIAM J from JERSEY CITY, NJ
- Really Easy
- Less than 15 mins
-
Screw drivers
Unplugged the stove and unscrew the 2 screws on the thermometer inside the stove and unplugged the white plastic in the back of the stove and I had to put the new extra piece that came with the sensor kit as it was needed because the socket were different.
Was this helpful?
Thank you for voting!
The old sealed burner cap had rusted out allowing gas flame around the base of the cap.
3 of 3 people
found this instruction helpful.
-
John from Stephentown, NY
- Really Easy
- Less than 15 mins
Note the position of the electrode on the side of the old burner cap. Turn the old burner cap one-eighth turn counter-clockwise to loosen and remove it. Raise the burner cap and disconnect the push-on connector wires from the ground and electrode. Clean the surface and connect the electrode and ground connector wires correctly to the n
... Read more
ew burner cap and place the burner cap back in the opening, positioning the electrode at the same orientation as it was with the old burner cap. Turn the cap one-eighth turn clockwise until the burner is snug. Turn on the burner control to test that the burner functions correctly. Make sure there is no smell of propane or gas when the burner is not in use which might indicate that the burner is not properly fitted snugly.
Read less
Was this helpful?
Thank you for voting!
Oven wouldn't heat.
3 of 3 people
found this instruction helpful.
-
Thomas from La Crescenta, CA
- Easy
- Less than 15 mins
-
Nutdriver
Slid two latches at rear of bottom oven pan toward door, pulled pan up at rear of oven and removed. Igniter exposed, removed two self-tapping screws with nutdriver, pulled wires surrounded by insulation up out of hole in ovenfloor an unsnapped plastic connector wired to old igniter. screwed new igniter to bracket, reconnected wires, pus
... Read more
hed connectors into hole and shoved new insulation around wires, fitted bottom pan and turned on oven. Works better than new, Thanks PARTSELECT.
Read less
Was this helpful?
Thank you for voting!
Crazy codes and not heating the oven properly at desired temp settings
3 of 3 people
found this instruction helpful.
-
Stan from CHICAGO RIDGE, IL
- Really Easy
- Less than 15 mins
-
Screw drivers
1. Turn power off and loosen and remove screws. Pull out sensor from mounting hole and expose wire connector. Remove old sensor. Select appropriate wire adaptor and reconnect the sensor. Carefully push connector through hole and secure with screws removed previously. Turn power back on and cycle oven to make sure oven operates properly. I
... Read more
f you have an oven thermometer it can be used to compare set point of oven to thermometer to make sure readings are the same. All done! Happy wife can now bake cookies again and now I can go back to man cave for other projects!
Read less
Was this helpful?
Thank you for voting!
Burners were rusted and rotten from the bottom, flames were coming from around the bottom
3 of 3 people
found this instruction helpful.
-
Alberto from Houston, TX
- Really Easy
- Less than 15 mins
all i did was twist the burner counter-clockwise unplug 2 wires and installed the new ones, real easy, it took me about 7-8 minutes for the 4 burners, that was all, our stove is working like new now, albert
Was this helpful?
Thank you for voting!
Oven and burners wouldn't light
3 of 3 people
found this instruction helpful.
-
Kory from Collingswood, NJ
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Easy repair. I removed the module housing at the back of the stove (two screws) and slipped the wires off the old spark module (I had to use pliers to gently pull one or two wires off--it's an old stove). The existing wires slipped right on the new module. I did have to use the mounting adapter that came with the kit, but that was the
... Read more
fiddliest part of the whole repair. It took me longer to move the stove out and back than it did to do the repair.
Read less
Was this helpful?
Thank you for voting!
rusted out burner on stove top
4 of 6 people
found this instruction helpful.
-
Roger from Mission, TX
- Really Easy
- Less than 15 mins
-
Pliers
turned burner counterclockwise and removed it reversed procedure and installed new one..
Was this helpful?
Thank you for voting!
Leaking gas from sides of burner
3 of 3 people
found this instruction helpful.
-
Homero from SEAGOVILLE, TX
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
Counterclockwise turn old burner to remove. Unplug attachment wires. Replug wires place back in place turn clockwise. Done.
Was this helpful?
Thank you for voting!
Gas range and top oven does not light up
3 of 3 people
found this instruction helpful.
-
Albert from Boston, MA
- Easy
- 15 - 30 mins
-
Screw drivers
I pulled out the gas range, unplugged the unit from the outlet. Unscrewed about two panels, one is the black cardboard panel located on top, then the aluminum main panel.
Located the spark module, unscrewed the unit from resting plate. Did not change the plate, although the new unit came with a new one, but it doesn't fit. S ... Read more o I just rested the new one on the old plate.
Pulled each wire slowly out and inserted it onto the new spark module.
Screwed in all the panels back and returned the stove to its proper place.
The range now works as well as the oven, but my broiler still does not light up.
Located the spark module, unscrewed the unit from resting plate. Did not change the plate, although the new unit came with a new one, but it doesn't fit. S ... Read more o I just rested the new one on the old plate.
Pulled each wire slowly out and inserted it onto the new spark module.
Screwed in all the panels back and returned the stove to its proper place.
The range now works as well as the oven, but my broiler still does not light up.
Read less
Was this helpful?
Thank you for voting!
Oven wouldn't heat/ turn on
3 of 3 people
found this instruction helpful.
-
Diane from NEW HAVEN, MO
- Really Easy
- 15 - 30 mins
-
Screw drivers
If you watched the video on installing the part it IS that easy. The connector piece matched exactly with what my oven already had so it was as simple as disconnecting the old piece and plugging in the new piece. There was no hidden challenges or obstacles to overcome. The oven works perfectly fine there was a slight smell when I first
... Read more
turned on the oven but I am attributing that to a new part. The smell did go away. I am 24 years old and a female who has limited knowledge in electrical/oven work.
Read less
Was this helpful?
Thank you for voting!