3131 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Gas range would not light
16 of 23 people
found this instruction helpful.
-
Mike from Menlo Park, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
Replaced spark module but same problem persisted. Realized that the insulation on the spark ignitors were all cracked, causing a short.
Lesson learned: check the condition of the spark ignitors first as these have a tendency to crack. Even the smallest crack will cause a short.
Ordered new spark ignitors and plan t ... Read more o complete repair.
Lesson learned: check the condition of the spark ignitors first as these have a tendency to crack. Even the smallest crack will cause a short.
Ordered new spark ignitors and plan t ... Read more o complete repair.
Read less
Was this helpful?
Thank you for voting!
Rubber gasket failed due to age
14 of 18 people
found this instruction helpful.
-
Mary from Woodland, WA
- Really Easy
- Less than 15 mins
-
Screw drivers
I learned that I could clean the window in the oven door. In taking it apart I saw that the gasket had fallen into the oven door. I found the part online, it arrived in three days. I removed the metal part of the door, removed what was left of the old gasket and put in the new one. Put the metal part of the door back on, and it was as g
... Read more
ood as new.
Read less
Was this helpful?
Thank you for voting!
Burners would not light and the flame would come out from the bottom of the burner.
13 of 15 people
found this instruction helpful.
-
juan from aurora, IL
- Easy
- 15 - 30 mins
A quarter turn counter-clockewise and the burner came out. Disconnect the old wires and connect the new wires. Place the burner in its place and a quarter turn clockwise and it was set.
Was this helpful?
Thank you for voting!
oven would not maintain temp
12 of 14 people
found this instruction helpful.
-
doyle from demorest, GA
- Really Easy
- Less than 15 mins
-
Screw drivers
. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) pushed wires back in and secured sensor
Was this helpful?
Thank you for voting!
oven would't go on
12 of 14 people
found this instruction helpful.
-
James from Fords, NJ
- Really Easy
- Less than 15 mins
-
Screw drivers
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I then conected the new element and replaced te two screws. Turned on the oven & works fine.
Very Easy!
Very Easy!
Was this helpful?
Thank you for voting!
burner head was rusted out. ordered 1 to see if part was correct. ordered 4 more to finish job.
13 of 17 people
found this instruction helpful.
-
Robert from Somerville, TN
- Really Easy
- Less than 15 mins
unscrewed old burner head ;disconnected 2 wires; repaced with new burner head and replaced wires. Unfortunately, before we really needed to replace the other burner heads, the cooktop itself developed a gas leak. We decided to replace the whole thing, and therefore would like to return the unboxed, unused 4 remaining burner heads.
Was this helpful?
Thank you for voting!
oven was only turning on occaisionally
14 of 22 people
found this instruction helpful.
-
Shayne from Angoon, AK
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers, Wrench (Adjustable)
I took the oven bottom out and then removed the screws that cover the safety valve, then I pulled the oven out and undid the safety valve in the rear of the oven. This was all accomplished with the electricity off and the propane also turned off. I then reinstalled the safety valve.
Other Parts Used:
Was this helpful?
Thank you for voting!
oven won't stay light
10 of 10 people
found this instruction helpful.
-
Shannon from Lake Park, IA
- Easy
- 15 - 30 mins
-
Screw drivers
removed racks, bottom plate. removed screws with a little bit of help from cooking spray. Unclipped old ignitor clipped in new ignitor, used old screws, and inserted insulation replaced racks, bottom shelf. Turn on oven and worked, been using it for about a week now. PS. ordered on monday morning arrived wednesday afternoon.
Was this helpful?
Thank you for voting!
gas burners and gas oven would not light
14 of 22 people
found this instruction helpful.
-
nicholas from livermore, CA
- Really Easy
- 30 - 60 mins
-
Screw drivers
unplug the oven and pull it away from the wall. looking at the oven from the back, the spark module is at the bottom on the lower left. there is a two piece sheetmetal cover over the area of the spark module. use a phillips head screwdriver to remove five screws and the covers come off. the spark module is the blue cube with four push
... Read more
on wire connectors. all you have to do is hold the new one next to the old one and swap one wire at a time. both were clearly marked with identical numbers and letters. really nothing to it. it took me longer to clean the back of the oven than to replace the module. the old module was eaton part number Y-54052-3. the new one is eaton part number Y-054052-34.
Read less
Was this helpful?
Thank you for voting!
Door Seal on oven was old, hard and breaking apart.
10 of 11 people
found this instruction helpful.
-
Kenneth from Friend, NE
- Really Easy
- Less than 15 mins
-
Pliers
It was very simple, pull off the old one, then I took some pliers and pulled out the fasteners. Took new gasket from bag and it just snapped into place.
Was this helpful?
Thank you for voting!
burner didn't self ignite or control flame
9 of 10 people
found this instruction helpful.
-
Geoffrey from Columbus, GA
- Really Easy
- 15 - 30 mins
-
Pliers
The burners turn and lift. I replaced two. One turned very easily, the other was stuck so I used liquid wrench and plumbers pliers. I did get it off. Once off, the old wires slipped right off and onto the new burners. Those twisted on very easily. Good as new easy breezy.
Was this helpful?
Thank you for voting!
Oven would not preheat and gave 'F1' error
9 of 11 people
found this instruction helpful.
-
Joshua from Reno, NV
- Really Easy
- 15 - 30 mins
-
Screw drivers
Had to unplug unit, remove back of unit (6 screws), then unscrew oven sensor (2 screws), then unplugged old sensor, replaced it and put back of oven on...Moving the oven out and working in the tight space avaialble was the most difficult. Other than that, super easy job that probably saved me a lot of $$$...
Was this helpful?
Thank you for voting!
F-3 error code
8 of 8 people
found this instruction helpful.
-
Mark from Lake Orion, MI
- Easy
- 15 - 30 mins
-
Screw drivers
I removed the two screws that attach the sensor to the oven wall. Then removed to more screws in the back of the oven and took off the rear cover, diconnected the sensor connector and installed the new sensor.
Was this helpful?
Thank you for voting!
Oven wouldn't ignite
8 of 8 people
found this instruction helpful.
-
Treasure from High Point, NC
- Really Easy
- Less than 15 mins
-
Screw drivers
First I unpuged the Range. Then I removed all racks and bottom tray of oven.
The Ignitor is located at back of oven, paralelle to the gas bar. I removed the 2 screws holding the ignitor and unpluged the wires. Then I put on the new ignitor, perfect fit, replaced the 2 screws and pluged in the wires , then pluged in the range. I tur ... Read more ned the oven on and it lit in about 10 seconds.
Thank you PartSelect for having such a wide range of range & oven parts . no one should have to pay a service tech. to fix most problems, as long as we have a GREAT SITE LIKE THIS ONE.
p.s. You guy also had one of the lowest prices , my part arrived ahead of schedule .
THANKS A LOT !
The Ignitor is located at back of oven, paralelle to the gas bar. I removed the 2 screws holding the ignitor and unpluged the wires. Then I put on the new ignitor, perfect fit, replaced the 2 screws and pluged in the wires , then pluged in the range. I tur ... Read more ned the oven on and it lit in about 10 seconds.
Thank you PartSelect for having such a wide range of range & oven parts . no one should have to pay a service tech. to fix most problems, as long as we have a GREAT SITE LIKE THIS ONE.
p.s. You guy also had one of the lowest prices , my part arrived ahead of schedule .
THANKS A LOT !
Read less
Was this helpful?
Thank you for voting!
When the oven was turned on, F2 and F4 came on. Oven wouldn't heat.
9 of 11 people
found this instruction helpful.
-
Crystal from Scott City, MO
- Really Easy
- Less than 15 mins
-
Screw drivers
After reading some of the repair stories, I was hesitant about doing this task. It was really very simple, I just removed the screws from the back of the stove, and removed the old element. I then replaced it with the new one and replaced the back cover. This whole task from start to finish took 10 minutes. The oven heats perfectly now ju
... Read more
st like a new oven.
Read less
Was this helpful?
Thank you for voting!