EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3116 - Instructions

All Instructions for the 3116
76 - 90 of 290

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
The oven igniter would glow red but gas did not come on to light the burner.
1 person found this instruction helpful.
  • Ernest from CINCINNATI, OH
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers, Wrench (Adjustable)
I watched a repair video, unplugged the electric,turned off the gas valve and disconnected the gas line. removed the shelves and burner tray. removed 2 screws and unplugged the igniter. Replaced the igniter and put tray and racks in.Hooked up gas and plugged in the electrical plug. Job done....
Was this helpful?
Thank you for voting!
no spark on top burners
2 of 4 people found this instruction helpful.
  • eric from winter haven, FL
  • A Bit Difficult
  • 15 - 30 mins
  • Pliers, Screw drivers
part was by the brolier drawer inside under stove removed 2 screws on cover/ part was attached to cover removed module line 1-2 fit/ had to use supplied disconects crimped on 4 burner wire leads/taped around module w/ elec. tape put back 2 screws finished. works now.
Was this helpful?
Thank you for voting!
No heat in oven
1 person found this instruction helpful.
  • Cynthia from AURORA, MN
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
Checked igniter it glowed but never got hot enough to open gas valve. I switched igniter from broiler to oven and oven burner lit. Switched igniter back to broiler as wires were shorter than the oven igniter. Ordered part from number and picture comparison. It took about 20 minutes to get it installed and all stove parts back together.
Was this helpful?
Thank you for voting!
The oven bottom was warped and could not be positioned properly in the oven.
1 person found this instruction helpful.
  • Tara from ALBANY, NY
  • Easy
  • 15 - 30 mins
Removing the old oven bottom was easy...as it was already outside of its slots. Installing the new one was pretty easy. I placed the oven bottom in the front slots first...then the rear slots...no tools necessary.
Was this helpful?
Thank you for voting!
Oven was not working at all
1 person found this instruction helpful.
  • Glynne from Dedham, MA
  • Easy
  • 1- 2 hours
  • Pliers, Screw drivers, Wrench (Adjustable)
My brother is a handyman. The part was delivered very quickly. The instructions were very easy to read and after an hour, voila the oven works perfectly!
Was this helpful?
Thank you for voting!
Oven was slow to get to temp and not holding temp
1 person found this instruction helpful.
  • Matt from Arlington, AL
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Thanks to previous posters, this seemed to be an igniter issue, and I found the idea of swapping the broiler igniter for the bottom one particularly good - I knew exactly what part was broken and how easy/hard the job would be prior to ordering. The part used snap in electric components, so the only work was in removing and re-installing the parts. Working in the oven was by FAR the most difficult part of the entire process.
Was this helpful?
Thank you for voting!
gas oven would not light
1 person found this instruction helpful.
  • carmine from ABINGTON, PA
  • Very Easy
  • 30 - 60 mins
  • Screw drivers
Remove oven door, remove burner bar, replace ignitor, splice wires together because the old electrical connectors had melted together. Shipping was fast and extra wire, insulation and ceramic wire nuts were included.
Was this helpful?
Thank you for voting!
Burners would not lite
2 of 4 people found this instruction helpful.
  • Lloyd from Cocoa, FL
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
I removed the old module ,replaced new bracket,crimped new wire lugs on wires. being an electrician for 50 plus years helped.      Thanks   Lloyd
Was this helpful?
Thank you for voting!
Gas would come on, would not ignite. Oven not heating.
1 person found this instruction helpful.
  • Karen from DAYTON, OH
  • Very Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Super easy. Turn off gas and unplug. Lift door off hinges, just pull up on it. Take racks out. Lift floor of oven out. You may need to release clips in the back of the oven, but mine were not engaged. Remove wing nut from shield plate and lift plate off. Using nutcracker, or Phillips screwdriver, remove screws holding the igniter to the brace plate. Carefully pull wires from the back of the oven wall. Carefully unplug the old part. Carefully plug in the new part. Feed wires back into the oven wall and install fiberglass padding. Replace screws, shield plate, wing nut, oven floor, oven racks and door. Door just slides back onto hinges. Watch the video on parts elect. Couldn't have been easier. Saved $500 on replacing my oven. $40 for DIY repair. Awesome!!!
Was this helpful?
Thank you for voting!
My oven door seal had dried rotted
1 person found this instruction helpful.
  • Anita from ELKTON, VA
  • Really Easy
  • 15 - 30 mins
  • Pliers
I took pliers to get the old one off, and popped the new one back in its place, and it fit perfect.
Was this helpful?
Thank you for voting!
igniter failed to ignite
1 person found this instruction helpful.
  • Gino from ARLETA, CA
  • Really Easy
  • Less than 15 mins
  • Socket set
Replaced the igniter by removing 2 screws, pulling on the wires to pull the connector in from the back thru the oval opening, screwing in the the new element, reconnecting the wires, pushing the connector back and that did it.
Was this helpful?
Thank you for voting!
Old seal breaking off oven door. Oven not baking food well, wasting heat and fuel.
1 person found this instruction helpful.
  • Mz from COLUMBIA, ME
  • Very Easy
  • Less than 15 mins
  • Pliers
Used pliers to remove clips and old seal. Snap in new seal. DONE! Less than 5 mins.
Was this helpful?
Thank you for voting!
35 year old range. grates too dirty to clean. Parts Select had exact replacement grates. Perfect fit.
1 person found this instruction helpful.
  • FRANCES from AFFTON, MO
  • Very Easy
  • Less than 15 mins
Easy, removed from box, put in place on range. Happy customer. Good company to find exact replacement parts.
Was this helpful?
Thank you for voting!
my knobs were broken on 30 year old range
1 person found this instruction helpful.
  • Larry from LAWTON, MI
  • Very Easy
  • Less than 15 mins
  • Pliers
I took a pair of channel locks pulled the old one off pushed the new one on they look really nice and was glad they had the parts for such an old stove. thank you,now my hubby is glad so he doesn't have to buy a new stove.
Was this helpful?
Thank you for voting!
Simply remove and install new parts
1 person found this instruction helpful.
  • Jacob from LITTLE CANADA, MN
  • Really Easy
  • 15 - 30 mins
Overall, it was painless and easy with zero problems
Was this helpful?
Thank you for voting!
All Instructions for the 3116
76 - 90 of 290