3116 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
oven would not heat up fully, smelled of gas.
1 person
found this instruction helpful.
-
Brian from Spotswood, NJ
- Really Easy
- Less than 15 mins
-
Screw drivers
Took off the top plate at the bottom of the oven, and the flame spreader, removed 2 screws on the igniter, pulled out the broiler tray and unplugged it. Took longer to get off the floor than it did to replace the part.
Was this helpful?
Thank you for voting!
Igniter for oven not working
1 person
found this instruction helpful.
-
RONNIE from SAG HARBOR, NY
- Easy
- Less than 15 mins
-
Wrench set
Instead of buying a new range my son said he could replace the part so I looked your company up on internet and had it shipped. Three days later I was cooking with gas again! Thanks!
Was this helpful?
Thank you for voting!
oven would not light reliably.
1 person
found this instruction helpful.
-
Joe from West Winfield, NY
- Easy
- Less than 15 mins
-
Screw drivers
Just like the example I removed the oven base, removed the two screws holding the igniter. Pulled out the wires opened the connector, plugged in the new igniter put everything back and turned on the oven. The oven now lights better than it did when new. And it holds a steady temp.
Was this helpful?
Thank you for voting!
Stove Would Not Light To Heat Up.
1 person
found this instruction helpful.
-
Nola from Enid, OK
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed grates and bottom plate two screws holding it. Turn oven light on and unwire the wire. Unscrewed the two screws and replace. This took my husband about ten min. And for him he says that this was a walk in the park. He says if he can do it anyone can. This was one of the easy honey dews. Good luck with yours. Nola & keith
Was this helpful?
Thank you for voting!
Oven Wouldn't Light. Smell Of Gas Before Lighting
1 of 2 people
found this instruction helpful.
-
Charles from Alexandria, VA
- Really Easy
- Less than 15 mins
-
Nutdriver
First I went online to find out about the availability of the part. In my search, I found what others had experienced and how they repaired it. Second, I ordered the part and followed others stories on their repair efforts. Third, I unplugged the range and removed the racks. Fourth, I removed the bottom of the oven which lifts out bac
... Read more
k first. Fifth, I removed the wing nut securing the flame difusser making it easier to access the element. Sixth, I had read that others had problems saving the original screws and/or threaded holes. I sprayed some wd-40 on both screws. They came out and back in without a hitch. Seventh, I removed and replaced the element, snap out, snap in. Eighth, I turned on the oven. It took about 15 seconds to glow but wow, it lit 5 seconds after that. I am my wife's hero!
Read less
Was this helpful?
Thank you for voting!
Bottom oven burner wouldn't light.
1 of 2 people
found this instruction helpful.
-
James from Lino Lakes, MN
- Easy
- Less than 15 mins
-
Nutdriver
If your igniter glows but the burner doesn't light, your igniter is more than likely bad. It should have at least 3.2V to gas valve when the igniter is glowing in order to open the gas valve. The repair is very easy with only a 5/16" nut driver equired to remove and replace the igniter. It's pretty much a plug and play reair.
Was this helpful?
Thank you for voting!
Stove top burners ignition were not working
1 of 2 people
found this instruction helpful.
-
Jeffrey from Somonauk, IL
- Really Easy
- Less than 15 mins
-
Screw drivers
1st unplug stove opened cover to wireing box with a phillips driver removed old part transfered wires one by one installed new part installed cover & pluged in stove & worked line new.
Was this helpful?
Thank you for voting!
Oven wouldn't heat. Igniter was broken.
1 of 2 people
found this instruction helpful.
-
Thomas from Allison Park, PA
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers, Socket set
I removed the back of the range to disconnect the wires to the igniter. Then I removed the two screws holding the igniter, screwed the new one in and reconnected the wires in back.
I was really pleased how easy it was to find the part on the website and how quickly the part came. The whole job was a snap. Thanks!
I was really pleased how easy it was to find the part on the website and how quickly the part came. The whole job was a snap. Thanks!
Was this helpful?
Thank you for voting!
Oven ignitor would glow but took 30 - 40 mins to heat
1 of 2 people
found this instruction helpful.
-
Catherine from Newton, IL
- Really Easy
- Less than 15 mins
-
Screw drivers
It took me 10 mins to replace the oven igniter and I did it myself. Oven is working fine now. I saved myself a $300.00 repair bill. Thank you for making the part available and saving me dollars!
Was this helpful?
Thank you for voting!
Thermostat bulb was hanging loose
2 of 5 people
found this instruction helpful.
-
Willi from Old Saybrook, CT
- Really Easy
- Less than 15 mins
-
Pliers
Removed what was left of the original clips. Pressed in the new clips and snapped in the themostat blub
Was this helpful?
Thank you for voting!
Drip pans were rusted. I had shopped for replacements at local appliance stores without finding them.
1 of 2 people
found this instruction helpful.
-
Norma J from Philadelphia, PA
- Really Easy
- Less than 15 mins
Removed the rusted drip pans and replaced them with the new pans. Range looks great and ready for many more years of use!
Was this helpful?
Thank you for voting!
Needed to replace two stove valve knobs.
1 of 2 people
found this instruction helpful.
-
Roberta from BROOKLYN, NY
- Really Easy
- Less than 15 mins
Inserting two stove valve knobs took 10 seconds! No tools necessary.
Was this helpful?
Thank you for voting!
Old and corroded drip pans
1 of 2 people
found this instruction helpful.
-
Veronica from Miami Beach, FL
- Really Easy
- Less than 15 mins
Furtunately, it was just a replacement of the drip pans. It changed the entite looks of my range for under $ 25.00 dollars. Very satisfied!
Was this helpful?
Thank you for voting!
Oven did not ignite
1 of 2 people
found this instruction helpful.
-
John from Racine, WI
- Really Easy
- 15 - 30 mins
-
Screw drivers
Remove the door... it just pulls up and out... set the release tabs so you can remove the bottom plate .. pull out broiler drawer... unscrew the 2 screws on the igniter ..let that hang... remove the cover for the termination.. and unplug the old igniter... then reverse everything to put back together..
Was this helpful?
Thank you for voting!
Oven wouldn't light
1 of 2 people
found this instruction helpful.
-
michael from newhall, CA
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Same as the other entries in this section.
The only thing I would add is a hint for removing the broiler igniter. As you can see from the oven igniter, the wires connect with a plug. For the top igniter, the broiler, the plug goes through the insulation and then through a hole in the rear panel of the oven. So, when you pull on it, y ... Read more ou will think it is stuck or the wire is pulled taut. That is because the plug hangs up on the rear panel.
Stick your finger through the square hole that you can see inside the oven, and follow the wire through the insulation. You will feel the small round hole in the back. You have to wiggle the wire up and around a bit to get the plug to fit through the hole. Then you will have the slack you need to change the plugs.
That way, you don't have to pull the whole oven out and break all the caulking seals.
The only thing I would add is a hint for removing the broiler igniter. As you can see from the oven igniter, the wires connect with a plug. For the top igniter, the broiler, the plug goes through the insulation and then through a hole in the rear panel of the oven. So, when you pull on it, y ... Read more ou will think it is stuck or the wire is pulled taut. That is because the plug hangs up on the rear panel.
Stick your finger through the square hole that you can see inside the oven, and follow the wire through the insulation. You will feel the small round hole in the back. You have to wiggle the wire up and around a bit to get the plug to fit through the hole. Then you will have the slack you need to change the plugs.
That way, you don't have to pull the whole oven out and break all the caulking seals.
Read less
Was this helpful?
Thank you for voting!