3116 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven and burners wouldn't light
3 of 3 people
found this instruction helpful.
-
Kory from Collingswood, NJ
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Easy repair. I removed the module housing at the back of the stove (two screws) and slipped the wires off the old spark module (I had to use pliers to gently pull one or two wires off--it's an old stove). The existing wires slipped right on the new module. I did have to use the mounting adapter that came with the kit, but that was the
... Read more
fiddliest part of the whole repair. It took me longer to move the stove out and back than it did to do the repair.
Read less
Was this helpful?
Thank you for voting!
Oven wouldn't heat/ turn on
3 of 3 people
found this instruction helpful.
-
Diane from NEW HAVEN, MO
- Really Easy
- 15 - 30 mins
-
Screw drivers
If you watched the video on installing the part it IS that easy. The connector piece matched exactly with what my oven already had so it was as simple as disconnecting the old piece and plugging in the new piece. There was no hidden challenges or obstacles to overcome. The oven works perfectly fine there was a slight smell when I first
... Read more
turned on the oven but I am attributing that to a new part. The smell did go away. I am 24 years old and a female who has limited knowledge in electrical/oven work.
Read less
Was this helpful?
Thank you for voting!
Leaking gas from sides of burner
3 of 3 people
found this instruction helpful.
-
Homero from SEAGOVILLE, TX
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
Counterclockwise turn old burner to remove. Unplug attachment wires. Replug wires place back in place turn clockwise. Done.
Was this helpful?
Thank you for voting!
Oven taking to long to preheat.
3 of 4 people
found this instruction helpful.
-
Isaac from LATHRUP VLG, MI
- Very Easy
- 30 - 60 mins
-
Screw drivers
Accessed igniter removed 2screws holding it.unpluged igniter installed new one.
Was this helpful?
Thank you for voting!
Oven burner would periodically go out and re-light
3 of 4 people
found this instruction helpful.
-
Richard from Merrimac, MA
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
The ignitor is held on by two screws which were rusted in place. When I tried to remove them, the screws became stripped and had to be cut off.
Once the part was free, the rest of the repair went quickly . At that point:
- Pull the element leads enough to get to the plastic connector
- Disconnect the old part
- ... Read more Connect the new part
- Re-attach to the bracket with new screws.
Once the part was free, the rest of the repair went quickly . At that point:
- Pull the element leads enough to get to the plastic connector
- Disconnect the old part
- ... Read more Connect the new part
- Re-attach to the bracket with new screws.
Read less
Was this helpful?
Thank you for voting!
oven would not light
2 of 2 people
found this instruction helpful.
-
gary from covington, LA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
New parts matched up perfectly. Undid screws holding old igniter, hardest part of procedure because one screw was frozen and broke off. Pulled stove out and new igniter"s connector was identical. Pushed stove back into place and it lighted on the first try.
Was this helpful?
Thank you for voting!
igniter burned out
2 of 2 people
found this instruction helpful.
-
David from Milton, MA
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers, Wrench set
Removed bottom tray of oven, unscrewed gas pipe, removed old igniter and replaced it. Spent some extra time digging around for leads, etc. before discovering that my new igniter was identical to the old one and all I had to do was plug it in.
Was this helpful?
Thank you for voting!
gas burners would not light with electric ignighters
3 of 5 people
found this instruction helpful.
-
Leo from Temple, TX
- Easy
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
using the diagram shown on line Looked up the ignition module and ordered it by phone. Received it the next day and installed it within the hour. Previously I had called the repairman and he said it would be a couple of weeks before he could look at it and a service call was $75 plus parts..I fixed it for the cost of the module $34. I
... Read more
am very satisfied.
Read less
Was this helpful?
Thank you for voting!
Oven would not ignite
2 of 2 people
found this instruction helpful.
-
Dominick from CLARKS SUMMIT, PA
- Very Easy
- Less than 15 mins
-
Screw drivers, Wrench set
Very easy, video helped tremendously
Was this helpful?
Thank you for voting!
The oven igniter came on but the gas valve never turned on.
2 of 2 people
found this instruction helpful.
-
James from PEORIA, IL
- Very Easy
- Less than 15 mins
-
Screw drivers
1. remove oven door 2. remove racks and oven floor 3. remove oven burner 4. unhook igniter 5. install new igniter 6. tuck wiring back in as reinstalling burner 7. put in the insulation supplied in kit 8. install floor and racks. 9. install door. 10. test system 11. oven came on. SUCCESS
Was this helpful?
Thank you for voting!
1960's oven door gasket fell apart, actual gasket not available any more
2 of 2 people
found this instruction helpful.
-
Mary from WINCHESTER, MA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Chose rubber flexible gasket with metal tabs. cut to size. unscrewed metal bracket on inside oven edge on 3 sides, slipped metal tabs between oven and metal and screwed back in. Done! Not a perfect fit but pretty good - better than no gasket.
Was this helpful?
Thank you for voting!
The problem was exactly what was described on your site.
2 of 2 people
found this instruction helpful.
-
William from FREELAND, MI
- Very Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I pretty much did the repair the same way the video described it. I first turned off the gas valve and disconnected the power. Then removed the two screws holding in the burner tube and removed it. Then I unplugged the old igniter. The screws were a bit corroded so I gave them a little spray of liquid wrench. They came right out them. Aft
... Read more
er removing them I replaced the igniter plugged it in. Then I put the wire through the hole in the wall of the oven. Replaced the insulation that was included in the kit. Replaced the burner tube on the venture. And reinstalled the screws. It was pretty cut and dry. The glow plug had the burner fired up in 15 seconds.
Read less
Was this helpful?
Thank you for voting!
Broken burner - easy fix
2 of 2 people
found this instruction helpful.
-
Don from NEW YORK, NY
- Really Easy
- 15 - 30 mins
-
Pliers
The burner was leaking a rust colored dirt and shooting flames all over the place. The top came off and I needed channel-locks to get the bottom half out. The wires were hard to get off and I broke one connector off so I soldered the wire on to the new part which fit the stove top perfectly. It still took less than a half hour to repla
... Read more
ce. Without problems it should take about 5 minutes.
Read less
Was this helpful?
Thank you for voting!
Burner igniter problem.
2 of 2 people
found this instruction helpful.
-
Dhirajlal from SKOKIE, IL
- Really Easy
- 15 - 30 mins
-
Pliers
Replaced with a new one.
Was this helpful?
Thank you for voting!
oven would take a very long time to warm
2 of 2 people
found this instruction helpful.
-
Barry from East Islip, NY
- Really Easy
- 15 - 30 mins
-
Nutdriver
took out both racks and under tray at bottom of stove no tools required.
used a nut driver to remove both screws holding ignighter in place ,pulled wires up gentily and remove from standard clip by pushing ends in.
clip new ignighter in place push wires down again and install 2 screws . put all back together and it works like ... Read more new .
used a nut driver to remove both screws holding ignighter in place ,pulled wires up gentily and remove from standard clip by pushing ends in.
clip new ignighter in place push wires down again and install 2 screws . put all back together and it works like ... Read more new .
Read less
Was this helpful?
Thank you for voting!