EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

31-397 Tappan Range - Instructions

All Instructions for the 31-397
46 - 60 of 1008

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Element burnt out
18 of 28 people found this instruction helpful.
  • Larry from Danville, IN
  • Easy
  • 1- 2 hours
  • Nutdriver
The old element burnt a hole in itself and just glowed in an area about the size of a quarter. I unplugged the oven, removed the two screws that held the element and removed it. I plugged the oven back in so we could use the top burners. When I went to install the new element I did not unplug the oven as the controls were off. I did not k now the element was hot from the outlet (by design) so when I tried to attach the new element sparks flew and it welded itself to the wire so I jerked it looose. I then unplugged the oven, replaced a blown fuse, and installed the element.
Was this helpful?
Thank you for voting!
Oven drawer fell out
14 of 16 people found this instruction helpful.
  • Donald from Gainesville, FL
  • Easy
  • 15 - 30 mins
Removed the one remaining drawer guide and stared at it for 10 minutes trying to understand where it came from and how it worked. Looked it up on partselect.com. While there was no part number, the detailed photo on your web site was enought to assure me that you had the correct part. Ordered them in a few moments and three days later I had the parts. The hardest part of the job was trying to understand how to install the widgets. After 20 minutes to crawling around in the stove's inards, I finally got the "aha" and the drawer on this antique stove was finished. Thanks! Couldn't have done it without you.
Was this helpful?
Thank you for voting!
burner wont heat all of the time
14 of 17 people found this instruction helpful.
  • Daivid from North Attleboro, MA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
removed old terminal block . cut wires and spliced new terminal block and insulated with shrink wrap. Very eazy
Was this helpful?
Thank you for voting!
Element caught fire when i preheated my oven
19 of 33 people found this instruction helpful.
  • Michael from Union City, TN
  • Really Easy
  • Less than 15 mins
I first turned the power supply off to my oven. Then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the ends. After that I connected the new element to the wires on my oven and secured the element with the two screws and turned the power back on. I pushed the oven-on button and now I'm back in business.
Was this helpful?
Thank you for voting!
burner wouldnt heat
11 of 13 people found this instruction helpful.
  • Doug from Ashton, IA
  • Really Easy
  • 15 - 30 mins
removed element , cut wires, conected wires,replaced element
Was this helpful?
Thank you for voting!
Replacement bowels didn’t fit
10 of 11 people found this instruction helpful.
  • Russell from ROEBUCK, SC
  • Really Easy
  • Less than 15 mins
Pulled the heating elements out took the bowels out that didn’t fit, threw them away and replaced them with the perfectly fitting bowels from this site and replaced the heating elements.
Was this helpful?
Thank you for voting!
Oven Racks needed to be replaced.
11 of 14 people found this instruction helpful.
  • Peter from Chicago, IL
  • Really Easy
  • Less than 15 mins
Slide out the old; slide in the new!
Was this helpful?
Thank you for voting!
Broiler element burned out
10 of 11 people found this instruction helpful.
  • Merlin from Newport News, VA
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Very important first step: Turn off the circuit breaker for the range or disconnect the power cord.
I removed the oven door to make it easier to access the back of the oven; remove two screws and the door lifts off of the brackets. Removed a screw from the top of the oven that secures one end of a wire that supports the broil eleme nt. Removed two screws that secure the broil element plate to the back of the oven. Pulled the element forward exposing the end terminals and wires. The wires are connected to the element by spade connectors. Used long nosed pliers to remove the connectors from the element. Pushed the connectors on to the new element and stuffed the ends of the element and wires back through the opening and the insulation. Reinstalled the two screws holding the element in place and the screw holding the wire in place across the top of the oven. Reinstalled the door. Took less than 30 minutes.
Was this helpful?
Thank you for voting!
F3 Error
10 of 13 people found this instruction helpful.
  • Jonathan from Lewisburg, PA
  • Really Easy
  • Less than 15 mins
  • Wrench set
I removed the back panel, about 6 screws, then found the probe which was attached by 2 screws. Unscrewed them and unplugged it. Plugged the new one in and replaced all the screws. The oven works like a charm now! No more F3 errors!
Was this helpful?
Thank you for voting!
Bake Element Stopped Working
11 of 16 people found this instruction helpful.
  • Meaghan from HOLLY HILL, FL
  • Very Easy
  • Less than 15 mins
  • Screw drivers
When I found the part I needed there was an instructional video on how to remove broken bake element and install new bake element. This was the best video short and sweet and anyone...I mean ANYONE could do it!

Step 1- cut off the power supply (I flipped by breaker, but you could just unplug the oven)
Step 2- remove bakin g racks
Step 3- unscrew the little metal plates inside the oven where the bake element meets the back of the oven (reserve screws for new element)
Step 4- carefully pull the bake element out until you have the wires through the holes
Step 5- carefully pull the bake element from the wire clips on both sides
Step 6- take broken element out of over and put new one in
Step 7- slide new bake element ends onto wire clips
Step 8- slide new bake element and connected wires back though back of oven
Step 9- used saved screws to screw metal plates on bake element to the back of the oven
Step 10- replace oven racks
Step 11- restore power to range
Step 12- enjoy a working oven and feel like an absolute PRO for fixing it yourself!!!!
Was this helpful?
Thank you for voting!
wiring was burnt off to burner
12 of 19 people found this instruction helpful.
  • Margaret from Portage "BlueKnob", PA
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
The range, (1988 Tappan) was givin to the church by one of our members. While using it, --after a period of time-- the wire burnt off to one of the burners. Since the couple gave us a brand new top for the stove that was still in the box, we decided to fix the stove up.
Now, with new wiring to all four burners, new shiney drip pans and,,,,a new top, we have a very new looking stove for in our church kitchen.
The parts I ordered from PartsSelect, came in just a few days of placing the order,
This is one site that I have wrote down in my address book for any future parts to items we may need.
Was this helpful?
Thank you for voting!
The temperature was irratic the entire time the stove was on. I would set it for 350 and it would go up to 425 then down to 275. It was all over the place.
9 of 10 people found this instruction helpful.
  • Jenifer from St. Marys, WV
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
It was great. We ordered the part, it was shipped the next day and I had it the day after that. It was easy to install and the stove has worked perfect since. Color us happy!
Was this helpful?
Thank you for voting!
Draw Glide Broken Off Bottom Drawer.
9 of 11 people found this instruction helpful.
  • Kathleen from fall river, MA
  • Really Easy
  • Less than 15 mins
New part arrived, opened pkg. , Pulled drawer out. . . Snapped in new parts. . . . Done!! Saved myself $100. 00.
Was this helpful?
Thank you for voting!
f3 alarm
8 of 8 people found this instruction helpful.
  • jeff from portage, MI
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Removed screws. Unplugged temp sensor. Put screws back in. So easy a caveman could do it.
Was this helpful?
Thank you for voting!
Electric burner switch shorted out.
9 of 12 people found this instruction helpful.
  • Armando G from Alice, TX
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Pliers, Screw drivers
First I unpluggd the range and removed the back cover using a nut driver. Then I removed the knob by pulling (using a little force),Not very hard to do. I uscrewed two screws that hold the switch from the front of the range. Then I pulled the switch out about three inches and used pliers to disconnect the wires one at a time and connec t them to the new switch. finally I finished the installation by reversing all the steps. Total time to install the switch took approximately 5(five) minutes.
Was this helpful?
Thank you for voting!
All Instructions for the 31-397
46 - 60 of 1008