31-397 Tappan Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Burners on 53 year old range kept going out
34 of 45 people
found this instruction helpful.
-
Matthew from Columbus, IN
- Easy
- 1- 2 hours
-
Screw drivers
When we bought our home less than a year ago, we had three functional burners on our 40" wide 50's classic Kelvinator (not close to standard size these-a-days). After a few months of use, two more burners went out for good and we were stuck using the back left burner for all of our cooking. I opted for the premium burners and made sure to
... Read more
compare my terminals with the ones online to be sure they mounted the same. I removed the burners and terminals, clipped the wires going into the terminals, and removed the top of the stove. I followed the directions that came with the new terminals, pushed in the new burners and viola! All four burners now work. I gave the stove a general cleaning and now my 1954 Kelvinator looks and cooks like it is brand new. It was easily the best $109 I've spent on my home.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Broiler element burned out
27 of 34 people
found this instruction helpful.
-
louis from cuba, NY
- Easy
- 15 - 30 mins
-
Socket set
Remove old element by removing two screws on back wall of oven, pull attached wires out about 6" and disconnect. Reverse to install, very easy. Of course the oven door makes it harder to get at things, but it all worked out. Partselect was the only place I could find the element since the stove is 18 years old. I love keeping appliances g
... Read more
oing as long as possible.
Read less
Was this helpful?
Thank you for voting!
Oven wouldn't heat up-panel kept showing F-3
25 of 30 people
found this instruction helpful.
-
Marilyn from Richmond, MO
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Pulled out the stove, removed the screws that held on the back panel, took out the 2 screws that held in the element and disconnected the wires and put the new one in. I put the screw back in and was finished!
Was this helpful?
Thank you for voting!
My bake element (lower element) just about caught fire and needed replacing
23 of 26 people
found this instruction helpful.
-
Ryan from Greenfield, MA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
The repair was straight forward and the video was a big help. I removed the oven racks and then used a 1/4" socket with a nut driver to unscrew the bolts at the back. Since this is a really old oven, the connecting wires were a bit difficult to remove from the bake element connectors. They seems kind of stuck, so I took a small, thin
... Read more
screw driver and pried up one of the metal clamps of the connecting wire just enough to let me budge the connector to detach the bake element. Had to do that for both sides. Then I just put the new bake element in, attached the wire connectors, made sure the wires and the ends of the bake element were all the way back in their holes, screwed the screws back in, and then put the racks back in. It was really easy, except for the bit of a challenge getting the wire connectors detached from the old bake element connectors. Works now without catching fire. :-D
Read less
Was this helpful?
Thank you for voting!
Right front burner would over-heat
23 of 27 people
found this instruction helpful.
-
Melvin from Attica, MI
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
First of all I removed the top panel then removed the switch. I then took pictures of the switch & drew a sketch with all the info. Then I went to your web site, matched up the switch & ordered.
When the switch arrived I went thru the above replacing the bad switch.
When the switch arrived I went thru the above replacing the bad switch.
Was this helpful?
Thank you for voting!
corroded terminals
22 of 25 people
found this instruction helpful.
-
Gary from hollywood, FL
- Easy
- 15 - 30 mins
was more of a job of splicing wires together than anything else. Loved the heat shrink electrical tubing
to put over the wires for insulation. used a hair
dryer. must buy more of that amazing stuff
to put over the wires for insulation. used a hair
dryer. must buy more of that amazing stuff
Was this helpful?
Thank you for voting!
Broken bake element
20 of 25 people
found this instruction helpful.
-
Chris from DeRidder, LA
- Really Easy
- Less than 15 mins
-
Nutdriver
From learning the hard way on a previous repair, I opened the circuit breaker for the oven at the circuit box (arc welders use 220 volts also). Then using a nut driver, I removed the two retaining screws and pulled the bake element from the oven (about 3"). Then I removed the spade connectors on both ends of the element and reconnected th
... Read more
em to the new element. Then I gently pushed the element back into the rear wall of the oven and replaced the retaining screws. This procedure is extreamly easy and very straight forward, anyone could accomplish this task.
Read less
Was this helpful?
Thank you for voting!
missing oven racks
20 of 25 people
found this instruction helpful.
-
ALLAN from APACHE JUNCTION, AZ
- Really Easy
- Less than 15 mins
order pcs fit perfect.
Was this helpful?
Thank you for voting!
Element shorted out
19 of 23 people
found this instruction helpful.
-
Patrick from Louisville, KY
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
I removed the screws holding the element in place, pulled the element out, and one of the leads came off and dropped into the oven. I had to take the back of the stove off and feed the lead back through the hole into the oven. If I had been careful to keep the leads from dropping out of the hole, the whole repair would have taken only a f
... Read more
ew minutes. But even so, it was quite easy.
REMEMBER TO UNPLUG YOUR APPLIANCE FIRST!
REMEMBER TO UNPLUG YOUR APPLIANCE FIRST!
Read less
Was this helpful?
Thank you for voting!
Old discolored drip pans that would not clean up.
17 of 20 people
found this instruction helpful.
-
Elizabeth from Smyrna, TN
- Really Easy
- Less than 15 mins
I simply removed the old drip pans and inserted the new ones which matched and fit perfectly.
I'm glad I found you on line. Your service was fast and the whole transaction was easy!! Thanks.
I'm glad I found you on line. Your service was fast and the whole transaction was easy!! Thanks.
Other Parts Used:
Was this helpful?
Thank you for voting!
Large burner would turn on high and not cycle off
17 of 20 people
found this instruction helpful.
-
Kevin from Nashville, TN
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers, Screw drivers
TURN BREAKER TO RANGE OFF! Move range out to access rear of the unit. Remove 6 screws to gain access to rear of controls panel. Pull knob off switch. Remove 2 pan head Phillips screws to take switch out. Lugs not in matching pattern but are clearly labled, swap wires one at a time. Reverse the disassembly steps and push the range bac
... Read more
k in place. DONE
Read less
Was this helpful?
Thank you for voting!
Block terminal burnt out, hot plate not working, needed to replace the terminal block
17 of 22 people
found this instruction helpful.
-
Shaun from Whitehall, MD
- Difficult
- More than 2 hours
-
Pliers, Screw drivers
This should take approx 15-30 mins. It took me 1.5 hours as I pushed the terminals into the wrong end of the block. It's very difficult to get them out when you do that... However, there are no easy instructions on the block or in the instructions to tell you which end to push the terminals into!!! So, with a 50:50 chance of getting
... Read more
it right, I got it wrong. I think most people would need to buy a new part if they do this. It would be very much easier if the block, had an arrow that simply said IN here so that this type of simple mistake is less easy to do... If you get that right, the fix is quite and straight forward. Good luck.
Read less
Was this helpful?
Thank you for voting!
The left front burner would not turn off, and the switch was sparking
15 of 17 people
found this instruction helpful.
-
Dan from Mulvane, KS
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
First I unplugged the stove, and removed the upper-back panel. Then I pulled off the control knob. Then I removed the two screws holding the switch to the stove. Then one-by-one I removed the wires from the old switch and connected them to the corresponding tabs on the new switch. Then, using the knob adapter supplied with the new swi
... Read more
tch, I figured out how much of the knob shaft I had to remove from the new switch to position the knob the correct distance from the face of the stove. Then I tested the switch with a voltmeter as instructed, and then I hooked up the last wire.
Partselect.com is an awsome website!!! I was able to review comments form other do-it-yourselfers that had similar problems. Then I looked up the Partselect schematic drawings of my stove and was easily able to find and order the part I needed. The part arrived at my house within a couple of days and I had the stove fixed in no time.
Partselect.com is an awsome website!!! I was able to review comments form other do-it-yourselfers that had similar problems. Then I looked up the Partselect schematic drawings of my stove and was easily able to find and order the part I needed. The part arrived at my house within a couple of days and I had the stove fixed in no time.
Read less
Was this helpful?
Thank you for voting!
Went to use the stove and the main baking element had a melt down.
17 of 23 people
found this instruction helpful.
-
Tracey from DEVILLE, LA
- Really Easy
- 15 - 30 mins
-
Screw drivers
shut off power to stove. Opened the oven door, removed the racks. removed 2 screws holding the element in place. gently pulled element out to expose connections. removed connections. discard old element. reattach connections to new element and reinstall. very simple.
Was this helpful?
Thank you for voting!
new switch was not wired like old one
20 of 33 people
found this instruction helpful.
-
PERRY from LECANTO, FL
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
i first replaced element after old smoked & quit. replaced switch but i noticed when i started to replace the wires one at a time something didn't seem right. after checking the #s on the old one, they didn't match up with the new one.luckily i had the stove diagram from a packet on the back of the stove. i traced each wire according to
... Read more
the diagram and everything worked out fine. i'm just glad i didn't replace each wire to wire.the #'s were on the switch where each wire went which was different than the org. even though they looked the same.
Read less
Was this helpful?
Thank you for voting!