EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

2927 - Instructions

All Instructions for the 2927
46 - 60 of 60

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
WATER WAS NOT SHUTTING OFF
3 of 17 people found this instruction helpful.
  • cathy. from etna, OH
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
I HAD A CHAT WITH LG EXPLAINED THE PROBLEM . SAID IT WAS THE WATER SHUT OFF VALUE. V EVEN SENT THE PAGE WITH PART# TO ORDER ONLINE.

LOVE LG CHAT!!!
Was this helpful?
Thank you for voting!
Washer Would Drain But Not Spin
0 of 31 people found this instruction helpful.
  • Nelson from Middletown, NY
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Wrench (Adjustable)
Removed rear cover (6 screws) unpluged harness from motor control and removed same. Replaced motor control reinstalled harness. Replaced rear cover. Parts used motor control board.
Was this helpful?
Thank you for voting!
Three of the four pivot hangers broke while the washer was spinning.
  • Charles from Millington, TN
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Once i got the parts I removed the top so I could get to the hangers. I removed the broken parts and replaced them with the replacement parts and rehung the tub and replaced the top.
Was this helpful?
Thank you for voting!
Humming, no error code, not spinning
  • Brian from Camden, MO
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
The problem ended up being the pump motor which discharges water from the washer. I figured out this was the problem after trying several things. I determined the motor was fine when it was empty. With the unit turned off, if you can rotate the tube with a quick spin and it lights up, probably this is OK. Then I tried to run it again and it went about 1/2 way through the cycle and stopped and started humming again. So I started emptying out the water, which I noticed was about 5 gallons which is way too much. so once empty, I took the pump off by turning unit on side. There are two hoses with hose clamps, and a few screws. Be careful to mark which wire plugs onto which side of the pump. One is brown and one is black. If you take the pump housing off, with the 3 screws, you should be able to pull the motor apart. Mine had water and scum from the wash in it, which was a dead give away that it was the problem.
Was this helpful?
Thank you for voting!
Replace top oven seal
  • Linda from Oxnard, CA
  • Really Easy
  • Less than 15 mins
This is a simple replacement. The hardest part was that I had to shorten the seal because it comes 15 to 17 inches. So it needed to be shortened to properly fit. I cut the seal to fit, then took the metal hook on the end and super glued it to the cut end. I put a weight on it to make sure
Was this helpful?
Thank you for voting!
Light bulb failure
  • Grant from Alexandria, VA
  • Really Easy
  • Less than 15 mins
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Was this helpful?
Thank you for voting!
Old burner bowls were pitted, rusted, and unattractive.
  • Lynn from Chelmsford, MA
  • Really Easy
  • Less than 15 mins
After too many years of trying to make do with worn out burner bowls, I finally searched on line for Caloric replacement parts. My order arrived THE NEXT DAY(!!!)and make my old range look almost new! They are so shiny and clean, and fit perfectly. I am so pleased, and wish I had ordered from PartSelect years ago! Thank you for your speed y service!
Was this helpful?
Thank you for voting!
All Instructions for the 2927
46 - 60 of 60