All Installation Instructions for Kenmore Dishwasher 19385

rear rollers on bottom rack broke off

real easy to install. i took off all 4 sets of rollers. i installed the first set improperly and the 2nd,3rd and 4th properly. i then went back and refasten the first one. no tools needed. 15 min.

Parts Used:

Tandem Rack Rollers - Set of 4

MARK from W.BARNSTABLE, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

broken roller wheels

Loading and unloading the dishwasher can be a pain if the rollers are not aligned or falling off. This part was easy to install even though it didn't exactly match the original (very old) dishwasher parts.

Parts Used:

Tandem Rack Rollers - Set of 4

Whitney from Menlo Park, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Both outside door handles turned very beige

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Parts Used:

Spray Paint - 12 oz. - White

Howard from Boynton Beach, FL
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

23 of 70 people found this instruction helpful.

Was this instruction helpful to you?

melted waste water guard

removed what was left of old guard and replaced it with new.

Parts Used:

GUARD

Gary from Erving, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

We needed a new bottom dishrack the old one was very rusty

I ordered a new rack, snapped the stuff together, and slid the old one out and the new one in. Fit beautifully. Piece of cake and much cheaper than a new dishwasher.

Parts Used:

Lower Dishrack Kit

Katherine from Coos Bay, OR
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

1 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Latch had broken on detergent dispenser cover

Remove retainer that holds door color slide in front of door & then remove the slide. Remove cardboard backing, remove electric latch release, remove latch & replace with new one. Open door & slide out the cup dispenser cover pin & spring & replace with new ones. This was all straight-forward & simple.

Parts Used:

Detergent Dispenser Cover Kit

Phillip D from Auburn, AL
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

8 of 26 people found this instruction helpful.

Was this instruction helpful to you?

Installed wheel assemblies to rack

Assemblies snap on, no tools needed

Parts Used:

Lower Dishrack Kit

Philip from Greene, ME
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

6 wheels missing

easy - removed old wheel holders & pushed new

ones in place. parts came in two days !!!!

Parts Used:

Tandem Rack Rollers - Set of 4

Tom from Wappingers Falls, NY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

soap door hinge broke

I took the pin and i slide it through the first hole attached the spring then sldie it through the second hole and snap the cover on

Parts Used:

Detergent Dispenser Cover Kit

Michael from Las Vegas, NY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

4 of 16 people found this instruction helpful.

Was this instruction helpful to you?

The previous rod holding the cup in place broke

Remove completely the old one and installed the new entire kit.

Parts Used:

Detergent Dispenser Cover Kit

Nicole from Newnan, GA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 12 people found this instruction helpful.

Was this instruction helpful to you?

was just missing the door and spring

You slide the pin that holds the door in the first hole. then you slide the spring in next. The you slide the pin through the last hole. After that you gently push the door onto the pin till it snaps into place. And your done.

Parts Used:

Detergent Dispenser Cover Kit

craig from Columbia, TN
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins

4 of 21 people found this instruction helpful.

Was this instruction helpful to you?

Super Fast Shipping

The part arrived the next day with regular postage, outstanding service.

Parts Used:

Upper Spray Arm Tower

Karolyn from Wellington, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

7 of 64 people found this instruction helpful.

Was this instruction helpful to you?

missing part

screw it in then hook up the hose.

Parts Used:

Drain Check Valve with O-Ring

Ruby from Saint Marys, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Unfortunately, a mouse had made its home on top of our surround insulation. For hygienic reasons, I replaced the surround.

1. Turn off the electrical switch that powers the dishwasher. 2. Open the door of the dishwasher and find the two phillips head screws that secure the top of the dishwasher to the kitchen counter. 3. Remove the screws. 4. Gently move the machine side-by-side a bit while pulling it out onto the kitchen tile (be careful, the water-supply hose, electric cord, and dishwasher drain hose may not be long enough to allow you to pull it out very far - don't break or kink the hoses). 5. Remove (pull off) the black plastic fastener located on the bottom/rear of each side of the dishwasher. 6. Remove the old surround. 7. Lay the new wrap in place and secure with the two plastic fasteners. 8. Push back into place, secure the two screws, check your hoses.

Parts Used: