1456 - Instructions

Slide oven door off slides and put oven door on table. Removed 2 torx-20 screws from top of oven door on the inside. Remove 4 sheet medal screws from the bottom of door 1/4' socket heads. The inside of the door will now separate from the front of door.Now you can see 2 screws on each side of the door handle end caps on 1/4 " socket heads. ... Read more Remove the 2 screws on which ever side is broken and remove old end cap and side new one on an install 2 screw. When you put door back together there are 2 spring steel spacers that fall off the top 2 screws that hold the inside and outside at the proper space! Parts Select service is EXCELLENT!!!!!

Required removing the door, by sliding it off the hinges (open 1/4 then lift up), removing the outer frame which releases the inner glass door section exposing the door end screws. Removed the phillips head screw on each door end releasing the old handle. Inserted the new handle in the ends, screws replaced, reversing the above. Thank ... Read more s for the correct part. Byron C.

I removed the burner element, then the drip pan. I took off the old block. Then I had to strip the old wires. Then I put on the heat sleeve, then attached the new wires to the old wires with nuts. Put heat sleeve over this and heated with lighter. Then put everything back together.

I removed the entire burner assembly to avoid having to turn things off at the breaker - the whole assembly can be removed completely from the stove I had. Once it was out and disassembled, the toughest part was putting the new wires into the new block correctly. Once that was done, I had to select the right mounting bracket - there were ... Read more 2 in the kit. Easy, just attention to detail. The rest of the instructions were easy to follow, re-doing the wires. The re-assembly was trivial, and it worked first time!

After carefully inspecting existing burner receptacles, I unscrewed them, raised and propped stove top. Determined which bracket to use from new kit and proceeded to cut and strip wires, twist ends together with supplied ceramic caps and heated shrink wrap on that junction. Works great. BTW got parts in 2 days in great shape and good dir ... Read more ections.

unscrewed broken end cap, removed from handle and replaced the new end cap

I shut off the breaker checked for power then cut old plugs making sure to allow a little slack. Tightened down wire nuts put on a couple wraps of electrical tape and that was it. Burners work great now I would reccomend this product to anyone with a similar problem.

Removed door from oven. Removed all side screws and pulled front assembly from door. Discarded old screws and broken plastic pieces. Put old handle in new end caps and lined them up with screw entry holes. It took 2 people to hold the door up while pressing in the screws to enter the new plastic receivers on the end caps. A pretty eas ... Read more y fix.

Pull door from oven and place on flat work surface. Remove bottom screws then the top screws and separate the two halves of the door . Remove broken door handles and replace reassemble door and place back on oven. The hardest thing was to clean the grease out of the inside of the door and get the glass clean to reassemble the door.

I noticed that one of the burner blocks was completely burned and the others were corroded. I ordered blocks for all four burners. Installation was easy except for one block. The screw holding the bracket to the range top was completely corroded in place. I used a correct size easy-out, which is a left hand tap and drill, to remove th ... Read more e screw. That took about five minutes, including tracking the easy-out down in one of my many toolboxes. The entire replacement of four blocks took about one and a half hours. Stove top cooks like new on all burners! The part kit had all the right parts and they fit like a glove!

After turning off circuit breaker to the stove, I removed all surface units , removed the 4 screws holding the top and lifted up. The plug in was burned out (the wire was burned). Look at the old plug-in so as to be able to match the new one and insert the pre- crimped end of wires into the block and the block into the metal holder that ... Read more matches your old one. (The kit comes with 2 different metal holders)After this, cut out the old wires and wire nut the new wires with the stove wires. Put shrink wrap protector on the wire nuts and heat to shrink it tight.attach the block to the stove top and wa la its done. Very easy.

I took a picture of the setup and damage . I then disconnected the burnt wires and replaced the wires . Then I installed the new terminal block and connected the wires to the proper positions. The reason for the failure was that the delivery people didn't tighten the cord when they installed the stove . I would check the connections per ... Read more iodically as to avoid another situation like this .

First, the order was shipped and delivered immediately. The model number had a wider range to select from and I had to guess which was the better fit. Other then that the new handle installation was a snap. Thank you and we would surely order from your company again.

The reason the brackets didn't go on to the handle far enough was there was a molding defect inside one of the brackets. After alot of scraping at the inside of the bracket and lightly tapping with a soft hammer I was able to get the defective bracket on so that the holes lined up to the mounting plate. As for the extra nipples I had ... Read more two options. Either cut the nipples off or drill some holes in the metal plate that the brackets attach to. I chose the latter. I had to attach the brackets to the plate with extra long screws, reach in under the bracket with a scribe and mark the nipple location on the plate. Then I removed the handle and drilled two holes for each bracket. After some minor adjustments to the holes I was able to attach both brackets and reassemble the oven door.

Very detailed repair instructions on internet made installation of new end caps a job not needing a professioal.