- Home
- 11020052994
- Instructions
11020052994 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
washer wouldn't drain
3 of 4 people
found this instruction helpful.
-
ed from pittsburgh, PA
- Really Easy
- 30 - 60 mins
-
Pliers
removed water lines from back of washer. tilted washer to get access to the pump/ removed 2 hoses at pump and removed to snap clips attaching the pump. easiest repair i ever did. washer works fine now.
Was this helpful?
Thank you for voting!
grinding noise and would not agitate
3 of 4 people
found this instruction helpful.
-
MARIA from TAMPA, FL
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers, Socket set
I loosened two screws which held the knob panel in place. I undid the two clips holding the cabinet and removed it. The pump has two clips holding it on, I removed those and the pump came free. Taking advice from these forums, I did not remove the hoses attached. I disconnected the wiring harnesses from the motor. The motor has 2 clips al
... Read more
so, these being held on with screws. I removed the screws and the clips. THE MOTOR IS HEAVY.
You will see the coupling on the "spindle" of the motor. In my case, both plastic pieces were cracked in 2 places. I removed the old coupling and cleaned the "spindles" and lightly regreased.
The replacement pieces I ordered were the "improved" ones with the metal insert. They were a tight fit on the motor but I used a socket and hammer. (lightly). Line up the coupling pieces, reattach clips, DONT FORGET THOSE SCREWS HOLDING THE MOTOR CLIPS. Pump goes on next, etc. MAKE SURE ALL WIRING IS RECONNECTED! Cabinet goes back on, large clips holding cabinet to rear of machine go back on. Knob console flipped down and reattached.
Plugged it in and I was good to go! This washer is almost ten years old and this is the second time I have been able to bring it back from the dead, the first time being the agitator "dogs" wearing out. THANKS PARTSELECT!
You will see the coupling on the "spindle" of the motor. In my case, both plastic pieces were cracked in 2 places. I removed the old coupling and cleaned the "spindles" and lightly regreased.
The replacement pieces I ordered were the "improved" ones with the metal insert. They were a tight fit on the motor but I used a socket and hammer. (lightly). Line up the coupling pieces, reattach clips, DONT FORGET THOSE SCREWS HOLDING THE MOTOR CLIPS. Pump goes on next, etc. MAKE SURE ALL WIRING IS RECONNECTED! Cabinet goes back on, large clips holding cabinet to rear of machine go back on. Knob console flipped down and reattached.
Plugged it in and I was good to go! This washer is almost ten years old and this is the second time I have been able to bring it back from the dead, the first time being the agitator "dogs" wearing out. THANKS PARTSELECT!
Read less
Was this helpful?
Thank you for voting!
Weak and broken springs on washing machine
3 of 4 people
found this instruction helpful.
-
Monty from OXON HILL, MD
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Looked at the repair instructions on your web site and it made the repairs simple and easy.
Other Parts Used:
Was this helpful?
Thank you for voting!
Washer tub goes out of balance in spin cycle.
3 of 4 people
found this instruction helpful.
-
Dale from DOTHAN, AL
- Really Easy
- 15 - 30 mins
-
Screw drivers
Found leveling spring loose on bottom of washer, the sheet metal on bottom of cabinet ad rusted through. Drilled new hole in sheet metal and installed new leveling spring. Greased hole with blue marine grease so it will last another 40 years.
Was this helpful?
Thank you for voting!
Water Pump leaked
3 of 4 people
found this instruction helpful.
-
alan from american fork, UT
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
We unscrewed the two screws at the back of the control panel. Holding the control panel on both ends
we pulled it toward the front of the machine, slightly and gently lifting it at the same time, removing it from the metal surround. Holding the control panel up off of the surround we rocked the surround forward and lifted it off t ... Read more he washing machine frame.
We could see where the leak was coming from. We took the hose clamps from the two ports, then
using a pair of pliers pulled the two clips that are holding the pump onto the shaft protruding from the
electric motor. We matched up the part on the web sight. Ordered the part then when it came in we just reversed the order putting the machine back together. The hardest and most time consuming
thing about this repair was the clean up of the washing machine. (Dirt and soap residue does
build up on the inside of the wash tubs.)
we pulled it toward the front of the machine, slightly and gently lifting it at the same time, removing it from the metal surround. Holding the control panel up off of the surround we rocked the surround forward and lifted it off t ... Read more he washing machine frame.
We could see where the leak was coming from. We took the hose clamps from the two ports, then
using a pair of pliers pulled the two clips that are holding the pump onto the shaft protruding from the
electric motor. We matched up the part on the web sight. Ordered the part then when it came in we just reversed the order putting the machine back together. The hardest and most time consuming
thing about this repair was the clean up of the washing machine. (Dirt and soap residue does
build up on the inside of the wash tubs.)
Read less
Was this helpful?
Thank you for voting!
rubber seal broke aprt
3 of 4 people
found this instruction helpful.
-
Lisa from North Attleboro, MA
- Really Easy
- Less than 15 mins
slid the old seal off the lid and the new one popped on so easily
I do so many self- repairs at home now this was not even an issue.
I do so many self- repairs at home now this was not even an issue.
Was this helpful?
Thank you for voting!
Agitator spun freely
4 of 7 people
found this instruction helpful.
-
Johnny from seminole, FL
- Easy
- Less than 15 mins
-
Socket set
I followed the online instructions and found it remarkably easy. I saved a lot of money and will certainly use PartSelect in the future! Washer works like new again!
Was this helpful?
Thank you for voting!
Water Pump Replacement
3 of 4 people
found this instruction helpful.
-
Jim from Hamburg, NY
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers
Yes, I agree that the actual replacement of the pump was an easy task on this whirlpool washing machine, however, unlike other posters, I had no access through the bottom of the machine. My machine has a solid pan on the bottom. It has a large hole in the center - I think to access the transmission, but no access where the pump is.
... Read more />So, I had to dismantle the entire enclosure, first the back (about 6 screws, a couple of electrical connections, etc.), then remove the rest of the enclosure to reveal the guts of the machine. I also had to disconnect a small vacuum tube attached to the tub, and remove the control console on top along with the back. It was pretty straight forward, took about two hours to dismantle. Then, the actual removal of the pump was as easy as others have described here - two spring clips and a hose clamp and I had it in my hand. I ordered the new part, which came very quickly - 2 days I think. Then I took another two hours to re-assemble the machine. It works - yeah!
Symptoms - water leak on the floor, it was actually intermittent for a time, so I procrastinated. Then when I actually did the work, I could see the rust trail and follow it to the leaky pump. The pump was actually leaking through the center, where the drive shaft from the motor goes. There is probably a seal between the impeller and the central drive slot that gives out after a while.
New pump in - machine back together - no leaks.
... Read more />So, I had to dismantle the entire enclosure, first the back (about 6 screws, a couple of electrical connections, etc.), then remove the rest of the enclosure to reveal the guts of the machine. I also had to disconnect a small vacuum tube attached to the tub, and remove the control console on top along with the back. It was pretty straight forward, took about two hours to dismantle. Then, the actual removal of the pump was as easy as others have described here - two spring clips and a hose clamp and I had it in my hand. I ordered the new part, which came very quickly - 2 days I think. Then I took another two hours to re-assemble the machine. It works - yeah!
Symptoms - water leak on the floor, it was actually intermittent for a time, so I procrastinated. Then when I actually did the work, I could see the rust trail and follow it to the leaky pump. The pump was actually leaking through the center, where the drive shaft from the motor goes. There is probably a seal between the impeller and the central drive slot that gives out after a while.
New pump in - machine back together - no leaks.
Read less
Was this helpful?
Thank you for voting!
Wash Stil Wet After Cycle Complete( Spin Cycle Not Working) Funny Noise When Should Be Spinning
4 of 7 people
found this instruction helpful.
-
Scott from Miami, FL
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Screw drivers
Started taking machine apart, would of been easier if I had looked at the online diagrams first, but dismantled enough to find a few broken parts, I could not tell the coupling was broke till I actually removed the water pump and motor. Total cost for 3 plastic parts was less than $25 including shipping. Received parts in 3 days on st
... Read more
andard lowest cost shipping. Put machine back together, with just a few extra screws and wire clips, but machine works like new now. Much better than the cost of new or used washer.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Washer would run, but not spin.
2 of 2 people
found this instruction helpful.
-
Justin from Ontonagon, MI
- Really Easy
- 15 - 30 mins
-
Pliers, Socket set
Unpluged washer. Turned washer on its side, unpluged wire harness to motor. Removed hoses to pump on motor, removed screws and nuts holding motor, then pulled out motor. Popped off old couplings,intalled new, reassembled. Piece of cake!
Was this helpful?
Thank you for voting!
Agitator would not work, pump works.
2 of 2 people
found this instruction helpful.
-
James from Gray, KY
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Unplug washer. Place large old towel in floor at rear of washer. Turn off and disconnect water supply lines and allow to drip dry. Place towel in floor in front of washer. Tip washer forward onto face of washer. Unplug wiring clip connector from drive motor. Remove 2 1/4 inch head screws from spring clips on bottom of motor housing. Slowl
... Read more
y rotate clips out of the was to drop motor. Knoch top coupling piece off agitator shaft with screwdriver and light hammer. replace coupling with 5/8 deep well socket as a driver which will fit the metal insert in the coupling and not interfere with the shaft. then drive the other coupling onto the motor shaft using light hammer and drive socket(5/8) deep well. place the rubber shock connector onto the agitator drive piece then slide the motor back into the mount position. rotate the clips vback into place. tighten 1/4 head screws in clips re-attach the wiring harness tip the washer back up onto "feet" re-attach water supply lines tighten appropriately. Plug unit into receptacle and enjoy....
Read less
Was this helpful?
Thank you for voting!
Hole in the water pump
2 of 2 people
found this instruction helpful.
-
Richard from Alexander, AR
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Just changed out the old pump with the new one. It went very quick and smooth!
Was this helpful?
Thank you for voting!
washer drum not turning
2 of 2 people
found this instruction helpful.
-
Jonathan from Glen Cove, NY
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Screw drivers
Turn off the power,remove the washer cabinet top and side panels. unsnap the water pump clips, unscrew and unclip the motor mounting clips.Remove the old drive coupling and triangular drive shaft adaptors.Clean area and install the three new parts, reattach the motor and pump, close the cabinet,turn the power back on and test.Done! The on
... Read more
ly hard part is working down on the floor and you need a good flashlight.
Read less
Was this helpful?
Thank you for voting!
Direct Drive Motor Coupling
2 of 2 people
found this instruction helpful.
-
derrick from paterson, NJ
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers, Socket set
Hello the installation was real simple I first uplug machine from wall I turn off all water leading to in to the machine I then tip machine on it side I then took loose all wiring leading to the motor then motor is held up with 3 screws and 2 bands that hold it in place I reinstall the new motor coupling insert the wires and turn back on
... Read more
the water leading to machine then plug machine back in, every thing was good to go. . . . Save a lot of money doing it my self so simple to do. . . .
Read less
Was this helpful?
Thank you for voting!
One of the plastic sprocket? of the coupler broke
2 of 2 people
found this instruction helpful.
-
john from larksville, PA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
Second time I did this. Same repair about 4 years ago. Pretty easy. Take the cabinet enclosure off, take pump off, remove motor and replace the coupling. Since the coupling is now reinforced with metal, a little more difficult to get on the drive shafts of the motor and the clutch drive?. $20.00 saved me $500.00 for now with a relat
... Read more
ively easy repair and hopefully with reinforced part, it will last a little longer.
Read less
Was this helpful?
Thank you for voting!